Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › from 2019.08
RM2850E _57 Power Source / Network _073263 CAN COMMUNICATION _0356688 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Urea Pump Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Urea Pump Control ECU Communication Stop Mode "Urea Selective Catalytic Reduction" cannot be normally selected on the system selection screen of the GTS
(Click here)
·

Emission control ECU assembly branch wire or connector

·

Power source circuit of emission control ECU assembly

·

Emission control ECU assembly ground circuit

·

Emission control ECU assembly



WIRING DIAGRAM

C421138E02
6.438,1.438 7.052,1.635 0.615,0.198 10 false IGSW 6.125,1.292 6.406,1.51 0.281,0.219 10 false 26 3.771,1.229 4.844,1.427 1.073,0.198 10 false ECU-IG1 NO. 6 1.917,1.396 3.313,1.635 1.396,0.24 10 false from IG1-NO.1 Relay 6.438,1.844 7.052,2.042 0.615,0.198 10 false BATT 6.135,1.729 6.417,1.948 0.281,0.219 10 false 30 6.448,3.021 7.063,3.219 0.615,0.198 10 false +BU4 6.438,2.646 7.052,2.844 0.615,0.198 10 false +BU5 6.156,2.906 6.438,3.125 0.281,0.219 10 false 33 6.167,2.51 6.448,2.729 0.281,0.219 10 false 51 6.448,2.24 7.063,2.438 0.615,0.198 10 false PB3 6.146,2.125 6.427,2.344 0.281,0.219 10 false 52 6.458,3.417 7.073,3.615 0.615,0.198 10 false RLY2 6.438,3.76 7.052,3.958 0.615,0.198 10 false +BU3 6.135,3.677 6.417,3.896 0.281,0.219 10 false 19 6.448,4.125 7.063,4.323 0.615,0.198 10 false +BU2 6.125,4.01 6.406,4.229 0.281,0.219 10 false 18 6.438,4.51 7.052,4.708 0.615,0.198 10 false +BU1 6.135,4.396 6.417,4.615 0.281,0.219 10 false 17 6.135,4.76 6.417,4.979 0.281,0.219 10 false 16 6.448,4.844 7.063,5.042 0.615,0.198 10 false RLY1 1.99,4.823 3.479,5.094 1.49,0.271 10 false to MTR DCU Relay 2.406,1.792 3.396,1.99 0.99,0.198 10 false from Battery 6.448,5.563 6.729,5.781 0.281,0.219 10 false E01 6.438,5.896 6.719,6.115 0.281,0.219 10 false E02 6.438,6.156 6.719,6.375 0.281,0.219 10 false E03 6.448,5.24 6.729,5.458 0.281,0.219 10 false EC 6.427,6.5 6.885,6.677 0.458,0.177 10 false GND4 6.438,6.833 6.896,7.01 0.458,0.177 10 false GND5 6.438,7.167 6.896,7.344 0.458,0.177 10 false GND6 6.438,7.521 6.896,7.698 0.458,0.177 10 false GND7 6.438,7.854 6.896,8.031 0.458,0.177 10 false GND8 5.604,8.25 7.083,8.625 1.479,0.375 10 false Emission Control ECU Assembly 6.156,5.135 6.438,5.354 0.281,0.219 10 false 42 6.156,5.469 6.438,5.688 0.281,0.219 10 false 38 6.167,5.781 6.448,6 0.281,0.219 10 false 39 6.146,6.083 6.427,6.302 0.281,0.219 10 false 40 6.156,6.385 6.438,6.604 0.281,0.219 10 false 41 6.146,6.698 6.427,6.917 0.281,0.219 10 false 46 6.146,7.042 6.427,7.26 0.281,0.219 10 false 47 6.156,7.396 6.438,7.615 0.281,0.219 10 false 48 6.156,7.75 6.438,7.969 0.281,0.219 10 false 49 3.979,4.354 4.823,4.573 0.844,0.219 10 false DCU NO. 4 3.896,1.677 4.74,1.896 0.844,0.219 10 false DCU NO. 3 5.604,8.073 5.979,8.292 0.375,0.219 10 false P12 1.865,4.479 3.354,4.75 1.49,0.271 10 false from MTR DCU Relay 1.802,3 3.333,3.219 1.531,0.219 10 false from UREA HTR Relay 6.156,3.302 6.438,3.521 0.281,0.219 10 false 27 6.427,0.385 7.042,0.583 0.615,0.198 10 false CAN+ 6.438,0.802 7.052,1 0.615,0.198 10 false CAN- 6.167,0.292 6.448,0.51 0.281,0.219 10 false 9 6.167,0.708 6.448,0.927 0.281,0.219 10 false 8 0.354,1 1.427,1.198 1.073,0.198 10 false P16 0.354,1.146 1.625,1.552 1.271,0.406 10 false No. 9 CAN Junction Connector 1.656,0.26 2.729,0.458 1.073,0.198 10 false 1 1.656,0.656 2.729,0.854 1.073,0.198 10 false 3 1.927,3.375 3.458,3.594 1.531,0.219 10 false to UREA HTR Relay

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (EMISSION CONTROL ECU ASSEMBLY BRANCH WIRE)
SST
09843-E7020  

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C421149C04
1.542,0.375 1.927,0.594 0.385,0.219 2.615,1.115 2.719,0.667 2.719,0.667 2.885,0.667 true 2.396,1.094 2.583,0.448 2.583,0.448 2.75,0.448 true 1.688,0.417 1.844,0.615 0.156,0.198 10 false E 0.104,0.104 0.385,0.302 0.281,0.198 10 false *a 2.927,0.594 3.365,0.813 0.438,0.219 10 false CAN+ 2.813,0.385 3.25,0.604 0.438,0.219 10 false CAN-
*a Signal Check Harness Connector


Connect the signal check harness to the emission control ECU assembly vehicle side harness.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA SELECTIVE CATALYTIC REDUCTION SYSTEM>TERMINALS OF ECM

NOTICE:

Connect the signal check harness to prevent damage to the connector and improve work efficiency when performing the check.


HINT:

Refer to the following table for the ECU connector terminals and their corresponding signal check connector terminals.

ECU Connector Terminal Signal Check Harness Connector Terminal
P12-9 (CAN+) E9 (CAN+)
P12-8 (CAN-) E8 (CAN-)



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E9 (CAN+) - E8 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
SST
09843-E7020  

a.

Measure the resistance according to the value(s) in the table below.

A444319C02
1.958,0.115 2.385,0.333 0.427,0.219 5.125,0.083 5.5,0.313 0.375,0.229 2.094,1.177 1.115,0.177 1.115,0.177 0.948,0.177 true 2.344,1.094 2.667,0.156 2.667,0.156 2.833,0.156 true 2.604,1.115 2.844,0.354 2.844,0.354 3.01,0.354 true 2.875,1.125 3.156,0.521 3.156,0.521 3.323,0.521 true 2.01,1.333 0.917,0.375 0.917,0.375 0.75,0.375 true 2.323,1.333 1.771,0.156 1.771,0.156 1.604,0.156 true 3.156,1.333 3.292,0.802 3.292,0.802 3.458,0.802 true 1.281,1.521 0.719,0.573 0.719,0.573 0.552,0.573 true 2.594,1.573 1.885,2 1.885,2 1.719,2 true 2.875,1.604 2.396,2.083 2.396,2.083 2.229,2.083 true 3.135,1.604 3.021,1.99 3.021,1.99 3.188,1.99 true 4.052,0.885 3.917,0.177 3.917,0.177 3.75,0.177 true 4.26,0.896 4.052,0.198 4.052,0.198 4.219,0.198 true 5.313,0.938 4.833,0.427 4.833,0.427 4.667,0.427 true 5.646,0.896 5.719,0.167 5.719,0.167 5.885,0.167 true 5.885,0.917 5.979,0.365 5.979,0.365 6.146,0.365 true 6.188,0.969 6.313,0.521 6.313,0.521 6.479,0.521 true 4.365,1.24 4.906,2.063 4.906,2.063 5.073,2.063 true 4.031,1.219 4.125,2.083 4.125,2.083 4.292,2.083 true 2.115,0.135 2.271,0.333 0.156,0.198 10 false E 5.24,0.125 5.396,0.323 0.156,0.198 10 false E 0.135,0.094 0.406,0.302 0.271,0.208 10 false *a 0.583,0.094 1,0.292 0.417,0.198 10 false RLY1 2.885,0.083 3.302,0.281 0.417,0.198 10 false +BU1 3.073,0.281 3.49,0.479 0.417,0.198 10 false +BU2 3.365,0.438 3.781,0.635 0.417,0.198 10 false +BU3 0.365,0.302 0.781,0.5 0.417,0.198 10 false IGSW 1.24,0.083 1.656,0.281 0.417,0.198 10 false RLY2 3.51,0.74 3.927,0.938 0.417,0.198 10 false BATT 0.188,0.5 0.604,0.698 0.417,0.198 10 false +BU4 1.427,1.906 1.844,2.104 0.417,0.198 10 false E01 1.969,2 2.385,2.198 0.417,0.198 10 false E02 3.24,1.906 3.656,2.104 0.417,0.198 10 false E03 3.354,0.094 3.771,0.292 0.417,0.198 10 false GND4 4.323,0.094 4.74,0.292 0.417,0.198 10 false EC 4.24,0.344 4.656,0.542 0.417,0.198 10 false GND5 5.948,0.094 6.365,0.292 0.417,0.198 10 false GND6 6.198,0.281 6.615,0.479 0.417,0.198 10 false GND7 6.542,0.448 6.958,0.646 0.417,0.198 10 false GND8 5.135,2 5.552,2.198 0.417,0.198 10 false PB3 4.344,2 4.76,2.198 0.417,0.198 10 false +BU5
*a Signal Check Harness Connector - -


Standard Resistance:
Tester Connection Condition Specified Condition
E42 (EC) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
E38 (E01) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
E39 (E02) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
E40 (E03) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
E41 (GND4) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
E46 (GND5) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
E47 (GND6) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
E48 (GND7) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
E49 (GND8) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω


NOTICE:

Connect the signal check harness to prevent damage to the connector and improve work efficiency when performing the check.


HINT:

Refer to the following table for the ECU connector terminals and their corresponding signal check connector terminals.

ECU Connector Terminal Signal Check Harness Connector Terminal
P12-30 (BATT) E30 (BATT)
P12-26 (IGSW) E26 (IGSW)
P12-52 (PB3) E52 (PB3)
P12-51 (+BU5) E51 (+BU5)
P12-33 (+BU4) E33 (+BU4)
P12-27 (RLY2) E27 (RLY2)
P12-19 (+BU3) E19 (+BU3)
P12-18 (+BU2) E18 (+BU2)
P12-17 (+BU1) E17 (+BU1)
P12-16 (RLY1) E16 (RLY1)
P12-42 (EC) E42 (EC)
P12-38 (E01) E38 (E01)
P12-39 (E02) E39 (E02)
P12-40 (E03) E40 (E03)
P12-41 (GND4) E41 (GND4)
P12-46 (GND5) E46 (GND5)
P12-47 (GND6) E47 (GND6)
P12-48 (GND7) E48 (GND7)
P12-49 (GND8) E49 (GND8)



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E30 (BATT) - Body ground Always 11 to 14 V
E26 (IGSW) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
E52 (PB3) - Body ground Battery positive (+) voltage applied to terminal E27 (RLY2) 11 to 14 V
E51 (+BU5) - Body ground 11 to 14 V
E33 (+BU4) - Body ground 11 to 14 V
E19 (+BU3) - Body ground Battery positive (+) voltage applied to terminal E16 (RLY1) 11 to 14 V
E18 (+BU2) - Body ground
E17 (+BU1) - Body ground



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR