Home › Engine / Hybrid System › N04C-VL (ENGINE MECHANICAL) › ENGINE UNIT › from 2019.08
RM2850E _51 Engine / Hybrid System _073160 N04C-VL ENGINE MECHANICAL _0356005 ENGINE UNIT A

N04C-VL ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL CAMSHAFT BEARING

a.
A151662E02
0.588,0.212 0.77,0.365 0.182,0.153 10 *1 0.395,0.94 0.56,0.322 false 1.54,0.802 1.684,0.266 false 2.608,0.112 2.988,0.264 0.38,0.153 10 No. 3 2.813,1.294 2.986,1.446 0.174,0.153 10 *2 0.683,1.698 1.064,1.851 0.38,0.153 10 No. 1 2.46,0.658 2.58,0.202 false 0.549,1.356 0.66,1.773 false 2.608,1.081 2.861,1.279 2.861,1.279 2.56,0.732 false 1.756,1.505 2.137,1.658 0.38,0.153 10 No. 2 1.638,1.225 1.733,1.58 false 1.718,0.175 1.9,0.328 0.182,0.153 10 *1

Be sure to face the notches of the No. 1 and No. 2 bearings and oil holes of the No. 3 bearing in the correct direction.

Text in Illustration
*1 Notch
*2 Oil Hole


b.
A151661E02
0.325,0.41 0.68,0.55 0.355,0.14 10 No. 1 1.329,0.41 1.684,0.55 0.355,0.14 10 No. 2 2.339,0.41 2.695,0.55 0.355,0.14 10 No. 3 2.673,1.58 2.97,1.727 0.297,0.147 10 SST 2.846,1.31 2.846,1.568 false

Using SST, install new camshaft bearings in the direction indicated by the arrow marks in the illustration.

SST
09215-00101  (09215-00130, 09215-00141, 09215-00150, 09215-00161)
09215-00013  (09215-00021, 09215-00461)

Journal Bearing Diameter:
Journal No. Inside Diameter Outside Diameter
No. 1 57.0 mm (2.2441 in.) 60.0 mm (2.3622 in.)
No. 2 56.8 mm (2.2362 in.) 59.8 mm (2.3543 in.)
No. 3 56.6 mm (2.2283 in.) 59.6 mm (2.3465 in.)


Text in Illustration
V100135

Front

NOTICE:

Install the bearings No. 2, No. 1 and No. 3 in order.



Hide 13201A 2.INSTALL CONNECTING ROD SMALL END BUSH

a.
A153825

Uniformly chamfer one edge of the bush hole at the small end of the connecting rod sub-assembly.

HINT:
·

Incorrect chamfering can cause the connecting rod small end bush to become out-of-round, which may result in jamming during insertion.

·

Remove dust from the inner surface of the connecting rod hole.




b.
A457681C02
1.167,0.219 1.292,0.219 1.292,0.219 1.854,0.573 true 1.031,1.104 1.24,1.104 1.24,1.104 1.771,1.417 true 1.104,1.573 1.354,1.573 1.354,1.573 1.792,1.74 true 2,1.698 2.51,1.698 true 2,0.938 2.51,0.938 true 1.396,2.01 1.906,2.01 true 0.969,0.115 1.198,0.313 0.229,0.198 10 false *a 0.906,1.49 1.094,1.656 0.188,0.167 10 false *c 1.177,1.927 1.417,2.104 0.24,0.177 10 false *d 0.833,1.01 1.031,1.198 0.198,0.188 10 false *b 2.552,0.854 2.771,1.031 0.219,0.177 10 false *e 2.552,1.615 2.75,1.844 0.198,0.229 10 false *e
*a SST (Spindle)
*b Bush
*c SST (Guide)
*d SST (Bolt)
*e Groove


Install the new connecting rod small end bush to SST and tighten the bolt.

SST
09222-E7020  09222-E7030  S9191-08252  

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

HINT:

Align the groove of SST (spindle) with the groove of SST (press sub-assembly) to install SST.


i.

Apply fresh engine oil to the connecting rod small end bush and guide.



c.
A153799C05
1.01,0.542 1.135,0.542 1.135,0.542 1.427,1.292 true 0.417,1.458 0.542,0.906 0.542,0.906 0.677,0.906 true 2.604,1.375 2.813,0.656 2.813,0.656 2.938,0.656 true 0.802,0.458 1.083,0.688 0.281,0.229 10 false *a 0.75,0.833 1,1.031 0.25,0.198 10 false *b 3.021,0.583 3.26,0.771 0.24,0.188 10 false *c
*a SST (Guide)
*b SST (Wing Nut)
*c SST (Press Sub-assembly)


Prepare SST.

SST
09222-E7010  S0948-11130  S9233-10360  

i.

Install the press sub-assembly to the guide by inserting the pin of the press sub-assembly into the guide, and then secure them together by installing the wing nut.

HINT:

Orient the guide so that the letter W, which is stamped on the guide, is above the pin.



ii.
A457679C03
2.573,0.688 2.885,0.688 true 2.396,0.594 2.604,0.781 0.208,0.188 10 false *a
*a Groove


With the connecting rod bearing removed, install the connecting rod bearing cap and place the connecting rod on SST with its chamfered side facing upward.

HINT:

Place SST so that the groove of SST (press sub-assembly) is at the center of the connecting rod.




d.
A457682C01
1.729,0.802 2.313,1.083 2.313,1.083 1.729,1.292 true 1.729,1.771 2.323,1.771 true 2.354,1.021 2.594,1.198 0.24,0.177 10 false *a 2.365,1.698 2.573,1.885 0.208,0.188 10 false *a
*a Groove


Align the groove of SST (guide) with the groove of SST (press sub-assembly) to install the connecting rod small end bush using a press.

HINT:

Align the groove of the SST (guide) with the groove of the SST (guide) with the groove of the SST (press sub-assembly) and install.



e.
A153798

Inspect the connecting rod small end bush position after installation.

i.

Make sure that the oil hole of the connecting rod small end bush and the oil path of the connecting rod are properly aligned, allowing a 6 mm (0.236 in.) diameter rod to pass through.

HINT:

Misalignment can lead to insufficient lubrication, which may result in piston seizure.



ii.

With a new piston pin inserted in the piston, make sure that the pin can be rotated by hand and is not loose.



Hide 13101A 3.INSTALL PISTON PIN HOLE SNAP RING

a.
A151668

Using snap ring pliers, install a new snap ring into one side of the piston hole.


Hide 4.INSTALL PISTON

HINT:

Before assembling the piston with the connecting rod, check whether the piston is specified for this engine. The check should be performed using the engine compatible identification code on the top of the piston.


Engine compatible identification:

95


a.

Assemble the piston and connecting rod.

i.
A151669

Gradually heat the piston to approximately 50°C (122°F).

CAUTION:

Do not touch the piston while it is hot.



ii.

Coat the piston pin with engine oil.


iii.
A269363E02
0.51,0.635 0.385,0.365 false 2.625,1.917 2.792,1.698 false 1.354,1.104 1.677,0.75 1.677,0.75 1.969,1.125 false 0.271,0.198 0.469,0.406 0.198,0.208 10 false *1 2.469,1.875 2.667,2.083 0.198,0.208 10 false *a 1.604,0.563 1.802,0.771 0.198,0.208 10 false *b

Install the piston onto the connecting rod with the notch on the piston facing in the same direction as the alignment mark on the rod.

Text in Illustration
*1 Notch
*a Alignment Mark
*b Matchmark


iv.

Match the matchmarks on the piston and piston pin, and then insert the piston pin.


v.
A151671

Check that the piston and piston pin fit securely.

HINT:

Try to move the piston back and forth.



vi.
A151672

Using snap ring pliers, install a new snap ring into the other side of the piston pin hole.



Hide 13011 5.INSTALL PISTON RING SET

a.
A151673

Using a piston ring expander, install them in the following order of the oil ring, 2nd ring and 1st ring.

HINT:
·

Attach the second ring so that the stamp mark is on the upper side.

·

Never change the combination of the coil and oil ring.

·

Connect the joint of the coil expander for the oil ring and install it inside the oil ring. Align the expander joint 180° opposite to the gap of the ring.




Hide 15708 6.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.

Install the No. 1 oil nozzle sub-assembly with the bolt.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)


NOTICE:
·

If the oil nozzle has been dropped or any impact has occurred to the nozzle, replace the nozzle with a new one.

·

Replace a deformed nozzle with a new one.




Hide 15605 7.INSTALL OIL CHECK VALVE SUB-ASSEMBLY

a.

Install a new gasket and the oil check valve sub-assembly.

Torque:
41.5 N*m (423 kgf*cm, 31 ft.*lbf)


Hide 11702 8.INSTALL CRANKSHAFT BEARING SET

a.
A151548E08
1.292,1.156 0.563,1.74 false 1.094,0.865 1.281,0.583 false 0.365,1.698 0.563,1.875 0.198,0.177 10 false *a 1.229,0.406 1.427,0.583 0.198,0.177 10 false *b

Match the upper bearing with an oil groove to the oil hole and concave section, attach it to the cylinder block, and then apply engine oil.

Text in Illustration
*a Oil Hole
*b Oil Groove

NOTICE:
·

Keep the back side of the bearing and the bearing surface free of foreign matter.

·

Do not apply engine oil to the attachment surface and the back surface of the bearing.

·

Check that the oil holes are aligned.

·

Misaligned oil holes can lead to a lack of oil, causing seizure.




b.
A450225

Attach the lower bearing to the convex section on the crankshaft bearing cap and apply engine oil.

NOTICE:
·

Keep the back side of the bearing and the bearing surface free of foreign matter.

·

Do not apply engine oil to the attachment surface and the back surface of the bearing.




c.

Face the oil groove surface of the thrust washer outwards and attach it to the crankshaft bearing cap. And then, apply engine oil.


d.

Install the crankshaft.


e.
A151674E02
1.875,1.845 2.079,1.991 0.205,0.146 10 *1 1.768,1.052 1.94,1.827 1.94,1.827 1.834,1.03 false

Insert the thrust washer into the clearance between the cylinder block and crankshaft with the oil groove facing outward.

Text in Illustration
*1 Groove


f.

Install the main bearing cap onto the cylinder block.

NOTICE:

The bearing caps must be installed so that the pentagonal marks on the bearing caps face the front of the engine, and that they are arranged in sequential order (1-2-3-4-5) from the front side.



g.

Apply a light coat of engine oil to the threads and under the cap bolt.

NOTICE:

Be sure to install the removed thrust washer to its original position.



h.
A151545E01
0.589,0.124 0.762,0.273 0.172,0.149 10 10 0.685,0.797 0.685,0.33 false 1.174,0.124 1.27,0.273 0.096,0.149 10 6 1.222,0.797 1.222,0.33 false 1.723,0.124 1.819,0.273 0.096,0.149 10 2 1.77,0.797 1.77,0.33 false 2.264,0.124 2.36,0.273 0.096,0.149 10 4 2.312,0.797 2.312,0.33 false 2.801,0.124 2.897,0.273 0.096,0.149 10 8 0.638,1.942 0.737,2.091 0.098,0.149 10 9 1.173,1.942 1.269,2.091 0.096,0.149 10 5 1.722,1.942 1.818,2.091 0.096,0.149 10 1 2.263,1.942 2.359,2.091 0.096,0.149 10 3 2.8,1.942 2.896,2.091 0.096,0.149 10 7 2.849,0.797 2.849,0.33 false 0.685,1.442 0.685,1.909 false 1.222,1.442 1.222,1.909 false 1.77,1.442 1.77,1.909 false 2.312,1.442 2.312,1.909 false 2.849,1.442 2.849,1.909 false

Temporarily install the 10 cap bolts in 2 to 3 steps, in the sequence shown in the illustration.


i.

Tighten the cap bolts to the specified torque, in the sequence shown in the illustration.

Torque:

60 N*m (612 kgf*cm, 44 ft.*lbf)



j.
A151546E02
1.802,0.233 2.042,0.383 0.24,0.15 10 60° 1.011,0.736 1.251,0.886 0.24,0.15 10 60° 1.173,1.692 1.36,1.845 0.187,0.153 10 *a 1.562,1.18 1.269,1.675 false

Mark the front of the bearing cap bolts with paint.

Text in Illustration
*a Paint Mark
V100135

Front


k.

Retighten the bolts by 60° and then an additional 60° as shown in the sequence shown in the illustration.

NOTICE:

Do not loosen to return the bolts in position if they have been tightened too much.



l.

Check that all the paint marks face the same direction.


m.

After tightening, use a plastic-faced hammer to lightly tap both the front and rear ends of the crankshaft.


n.

Check that the crankshaft rotates smoothly.


Hide 11462 9.INSTALL CYLINDER LINER

HINT:
·

When assembling the cylinder liner into the cylinder block, the clearance can be set to 3 levels.

·
A448342C02
1.438,1.854 1.042,1.385 false 1.438,1.844 2.292,1.385 false 1.396,4.094 1.719,3.5 false 1.385,1.875 1.698,2.188 0.313,0.313 10 false *a 1.26,4.094 1.573,4.406 0.313,0.313 10 false *a
*a Position of Mark A, B or C


The upper surface and side surface of the cylinder block are stamped A, B or C. When using a new cylinder liner, insert a matching cylinder liner with the same symbol.



a.

Apply engine oil to the cylinder block inside bore.


b.
A151676E02
0.829,0.847 1.016,0.996 0.187,0.148 10 *a 1.294,1.188 1.045,0.939 false

Align the marks of the cylinder liner and cylinder block.

Text in Illustration
*a Mark

HINT:

When reusing the cylinder liner, install it according to the marks made during the removal. When reusing the cylinder liner, misalignment with the cylinder block may concentrate stress on the thin part of the cylinder liner and it may break.



c.

Install the cylinder liner.

NOTICE:

Make sure to install the cylinder liner to its original location.



Hide 10.INSTALL PROTRUSION OF CYLINDER LINER

a.
A151677E01
0.212,0.142 0.51,0.29 0.297,0.148 10 SST 0.795,0.45 0.579,0.233 false

Mount SST onto the cylinder block.

SST
S0942-01460  


b.

Tighten the center bolt to the specified torque below to set SST in the proper installation position.

Torque:

9.8 N*m (100 kgf*cm, 87 in.*lbf)



c.
A448343C02
0.938,0.698 1.302,0.938 0.365,0.24 10 false *a
*a Protrusion


Using a dial indicator, measure the protrusion of the cylinder liner.

Standard Protrusion:

0.01 to 0.08 mm (0.000394 to 0.00315 in.)


Maximum Protrusion:

0.08 mm (0.00315 in.)


If the protrusion is greater than the maximum, replace the cylinder liner.


Hide 13202 11.INSTALL CONNECTING ROD BEARING

NOTICE:
·

When reusing the bearing, reassemble the removed bearing as it was originally installed.

·

Install the bearing with the oil hole onto the connecting rod side and install the bearing without the oil hole onto the cap side.

·
A450223C03
2.052,0.229 2.219,0.229 2.219,0.229 2.5,0.781 true 1.844,0.156 2.104,0.333 0.26,0.177 10 false *a
*a Protrusion


Match the bearing protrusion with the notch of the connecting rod or cap.

·

Keep the back side of the bearing and bearing surface of the bearing cap free of foreign matter.

·

Do not apply engine oil to the attachment surface and the back surface of the bearing.



Hide 12.INSTALL PISTON WITH CONNECTING ROD

HINT:
A151680E02
1.888,0.166 2.237,0.318 0.348,0.152 10 *1 1.019,0.287 1.194,0.458 0.174,0.171 10 *3 1.088,1.836 1.269,2.008 0.182,0.171 10 *4 2.597,1.028 3.178,1.2 0.581,0.171 10 *2 1.6,1.535 1.775,1.682 0.175,0.147 10 95

Position the gaps of the piston rings at an even distance. Be careful not to position the gaps at the same position as the piston mark.

Text in Illustration
*1 Mark
*2 1st Ring
*3 2nd Ring
*4 Oil Ring


a.

Place the crankshaft for the cylinder where the piston with connecting rod is to be attached in the TDC.

NOTICE:

If the crankshaft is in a position other than the TDC, the connecting rod may interfere with the No. 1 oil nozzle.



b.
A151681

Using a piston ring compressor and a hammer handle, insert the piston with connecting rod assembly into the cylinder block.

HINT:
·

Insert the piston and connecting rod to the matching cylinder using the cylinder identification numbers.

·

Check that there are no deformations or damage to the piston ring compressor.

·

Before the installation, apply engine oil to the piston pin, piston ring, cylinder liner and connecting rod bearing.

·

Check the gap of each piston ring.

·

Be careful not to damage the cylinder liner, crankshaft, and No. 1 oil nozzle during the operation.



i.
A151682E05
1.594,1.667 1.427,1.875 1.427,1.875 1.927,1.656 false 2.427,1.521 1.781,1.271 false 2.469,1.458 2.688,1.625 0.219,0.167 10 false *1 1.26,1.833 1.458,2.01 0.198,0.177 10 false *2

Make sure that the mark on the piston is on the tappet chamber side.

Text in Illustration
*1 Mark
*2 Tappet Chamber



c.
A260710E02
1.26,0.74 1.542,1.146 0.281,0.406 1.271,1.229 1.552,1.635 0.281,0.406 1.542,0.948 2.375,0.948 false 1.552,1.448 2.135,1.448 2.135,1.448 2.135,0.948 false 2.427,0.854 2.646,1.094 0.219,0.24 10 false *a

Align the matchmarks and install the bearing cap onto the connecting rod with the front mark facing in the correct direction.

Text in Illustration
*a Matchmark


d.

Apply a light coat of engine oil to the threads of the connecting rod cap bolts.


e.

Uniformly install and tighten the 2 bolts to the specified torque in 2 to 3 steps.

Torque:

30 N*m (306 kgf*cm, 22 ft.*lbf)



f.
A151683E02
1.527,1.726 1.715,1.872 0.188,0.146 10 *a 1.847,0.227 2.083,0.373 0.236,0.146 10 60° 1.068,0.694 1.305,0.84 0.236,0.146 10 60° 1.624,1.179 1.624,1.707 false

Mark the front side of the bolt head with paint.

Text in Illustration
*a Paint Mark
V100135

Front


g.

Retighten the bolts by 60° as shown in the illustration.


h.

Perform step (e) again.


i.

Check that each paint mark is now at a 120° angle to the front.


Hide 11381A 13.INSTALL REAR ENGINE OIL SEAL

a.
A151492E05
1.604,1 2.938,0.49 false 2.938,0.323 3.24,0.479 0.302,0.156 10 true SST 2.573,1.635 2.729,1.792 0.156,0.156 10 false *a

Using SST and a hammer, tap in a new engine rear oil seal until it is 4 mm (0.157 in.) below the upper edge of the flywheel housing.

SST
09223-78010  

Text in Illustration
*a 4 mm (0.157 in.)

NOTICE:
·

Be careful not to tap the oil seal at an angle.

·

Keep the gap between the rear oil seal retainer edge and the oil seal free of foreign matter.




b.

Apply MP grease to the oil seal lip.


Hide 11351 14.INSTALL FLYWHEEL HOUSING

a.
A151493E06
0.979,1.896 1.552,2.948 1.552,2.948 2.063,1.896 false 0.573,0.229 0.969,0.521 false 1.458,2.979 1.635,3.146 0.177,0.167 10 false *1 0.417,0.104 0.594,0.271 0.177,0.167 10 false *1

Remove any old seal packing material from the contact surface.


b.

Apply a continuous bead of seal packing (diameter: 1.5 to 2.5 mm (0.0591 to 0.0984 in)) as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Text in Illustration
*1 Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the flywheel housing within 3 minutes of applying the seal packing.

·

Do not expose the seal packing to engine oil for at least 2 hours after installation.




c.

Install the flywheel housing with the 14 bolts.

Torque:
M14 Bolt:

132 N*m (1346 kgf*cm, 97 ft.*lbf)

M8 Bolt:

29 N*m (291 kgf*cm, 21 ft.*lbf)



Hide 13453 15.INSTALL FLYWHEEL RING GEAR

a.
A452021E01
1.563,0.531 2.063,0.448 false 0.927,0.406 1.438,0.469 false 1.75,1.083 2.25,1 false 0.719,0.333 0.938,0.531 0.219,0.198 10 false *1 2.094,0.375 2.333,0.604 0.24,0.229 10 false *2 2.292,0.938 2.583,1.167 0.292,0.229 10 false *3 1.625,0.167 1.938,0.323 0.313,0.156 10 false *a

Using a torch, heat the ring gear evenly to approximately 200°C (392°F).

Text in Illustration
*1 Chamfer
*2 Ring Gear
*3 Flywheel
*a 0.25 mm (0.00984 in.) or less

NOTICE:

Be careful not to overheat the ring gear.



b.

Using a brass bar, strike the ring gear onto the flywheel with its chamfered gear teeth facing the block.

Standard Clearance:

0.25 mm (0.00984 in.) or less


NOTICE:

After installing, allow the ring gear to cool before handling.



Hide 13450A 16.INSTALL FLYWHEEL SUB-ASSEMBLY

a.

Insert the flywheel slowly until it contacts the collar knock in order to prevent impact with the guide bar. Adjust the position, then insert it completely.

NOTICE:

The flywheel is heavy. When installing, be careful not to drop it.



b.

Apply clean engine oil to the threads of the flywheel bolts and the flywheel bolt seats.


c.
A151470

Insert a screwdriver through the inspection hole of the flywheel housing into the ring gear of the flywheel to keep it from turning together with the crankshaft.


d.
A348668E01
1.646,0.625 1.802,0.823 0.156,0.198 10 false 1 1.896,0.74 2.052,0.938 0.156,0.198 10 false 8 1.979,0.99 2.135,1.188 0.156,0.198 10 false 4 1.896,1.24 2.052,1.438 0.156,0.198 10 false 6 1.656,1.323 1.813,1.521 0.156,0.198 10 false 2 1.396,1.219 1.552,1.417 0.156,0.198 10 false 7 1.396,0.75 1.552,0.948 0.156,0.198 10 false 5 1.302,0.99 1.458,1.188 0.156,0.198 10 false 3

Tighten the flywheel bolts in several steps in the order shown in the illustration.

Torque:

86 N*m (877 kgf*cm, 63 ft.*lbf)



e.
A348672E02
1.094,1.542 1.365,1.25 false 0.938,1.531 1.25,1.729 0.313,0.198 10 false *a 0.76,0.688 1.073,0.885 0.313,0.198 10 false *b

Mark the front of the flywheel bolts with paint.

Text in Illustration
*a Paint Mark
*b 45°


f.

Tighten the flywheel bolts 45° in several steps in the order shown in the illustration.


g.

Check that the paint marks are now at a 45° angle to the front.


h.
A151495

Using a dial indicator, measure the runout of the flywheel sub-assembly.

Maximum Runout:

0.15 mm (0.00591 in.)


If the runout is greater than the maximum, resurface the sliding surface.


i.
A151486

Temporarily install 4 bolts in the positions of the cylinder block shown in the illustration to prevent the wires from sliding toward the center of the block.


j.

Attach 2 wires to the cylinder block.

HINT:

The wires must be attached outside the installed bolts.



k.

Using a chain block and an engine sling device, install the cylinder block onto the engine stand.


l.

Remove the 4 bolts from the cylinder block.


Hide 11311H 17.INSTALL FRONT END PLATE

a.
A151485

Install the front end plate with a new front end plate gasket and 4 bolts.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)



b.
A260709E03
0.635,1.094 1.052,1.094 false 1.802,1.552 2.219,1.552 false 0.99,1.729 1.156,1.729 1.156,1.729 1.458,1.406 false 0.969,0.24 1.135,0.24 1.135,0.24 1.354,0.51 false 1.5,0.531 1.667,0.313 1.667,0.313 1.833,0.313 false 0.802,0.156 1.115,0.354 0.313,0.198 10 false *2 1.875,0.219 2.188,0.417 0.313,0.198 10 false *3 2.042,0.604 2.354,0.802 0.313,0.198 10 false *4 2.24,1.469 2.552,1.667 0.313,0.198 10 false *a 0.479,1 0.792,1.198 0.313,0.198 10 false *1 0.844,1.615 1.156,1.813 0.313,0.198 10 false *b

Using a cutter, cut the gasket so that it is flush with the lower surface of the cylinder block.

Text in Illustration
*1 Timing Gear Case
*2 Front End Plate
*3 Gasket
*4 Cylinder Block
*a Cutter
*b Cut


Hide 15100 18.INSTALL OIL PUMP ASSEMBLY

Hide 19.INSTALL CRANKSHAFT TIMING GEAR OR SPROCKET

a.
A151497E03
0.233,0.176 1.865,0.391 1.632,0.215 10 *a 2.963,1.223 2.733,1.976 2.733,1.976 2.76,1.251 false 2.66,1.987 2.841,2.148 0.181,0.161 10 *b

Turn the crankshaft clockwise, and align the matchmarks of the flywheel sub-assembly and flywheel housing to set the No. 1 cylinder to TDC.

Text in Illustration
*a TDC of No. 1 and No. 4 Cylinders
*b Matchmark


b.

Align the set key on the crankshaft with the key groove of the crankshaft timing gear.


c.

Using a hammer, tap in the crankshaft timing gear.


Hide 13508M 20.INSTALL NO. 1 IDLE GEAR SUB-ASSEMBLY

a.
A151498E02
2.527,1.554 2.709,1.703 0.183,0.149 10 *1 1.944,1.212 2.609,1.537 false

Install the idle gear and idle gear thrust plate onto the idle gear shaft.

Text in Illustration
*1 Oil Hole


b.
A153732E05
2.01,2.604 1.406,2.969 false 1.448,1.094 2.302,1.604 2.302,1.604 2.115,2.479 false 1.417,1.188 2.302,1.604 2.302,1.604 2.01,2.448 false 1.24,1.063 0.802,1.583 0.802,1.583 1.292,1.083 false 0.677,1.563 0.875,1.771 0.198,0.208 10 false *a 2.333,1.51 2.531,1.719 0.198,0.208 10 true *a 1.229,2.906 1.427,3.115 0.198,0.208 10 true *a

With the idle gear shaft oil hole facing down, match the alignment marks for each gear, and insert the shaft into the cylinder block.

Text in Illustration
*a Alignment Mark

NOTICE:

If the oil hole is not facing down, it will cause burning or abnormal wear.



c.

Tighten the bolt.

Torque:

137 N*m (1397 kgf*cm, 101 ft.*lbf)



Hide 13581C 22.INSTALL NO. 2 IDLE GEAR SHAFT

a.

Install a new O-ring onto the No. 2 idle gear shaft.


b.
A151501E02
2.593,1.752 2.753,1.905 0.16,0.153 10 *1 1.966,1.443 2.647,1.726 false

With the idle gear shaft oil hole facing down, install the No. 2 idle gear shaft onto the lock plate with the 3 bolts.

Torque:

55 N*m (561 kgf*cm, 41 ft.*lbf)


Text in Illustration
*1 Oil Hole

NOTICE:

If the oil hole is not facing down, it will cause burning or abnormal wear.



Hide 13508N 23.INSTALL NO. 2 IDLE GEAR SUB-ASSEMBLY

a.
A151502E07
1.781,1.25 1.823,1.292 0.042,0.042 1.917,1.292 1.958,1.333 0.042,0.042 1.896,1.177 1.938,1.219 0.042,0.042 1.927,1.188 2.188,0.635 2.188,0.635 1.938,1.302 false 1.135,1.76 1.802,1.271 false 0.99,1.781 1.177,1.969 0.188,0.188 10 true *a 2.198,0.531 2.427,0.719 0.229,0.188 10 false *a

Match the alignment marks of the No. 1 and No. 2 idle gear sub-assemblies and install the No. 2 idle gear shaft.

Text in Illustration
*a Alignment Mark


Hide 13572C 24.INSTALL NO. 2 IDLE GEAR THRUST PLATE

a.

Install the No. 2 idle gear thrust plate with the 2 bolts.

Torque:

55 N*m (561 kgf*cm, 41 ft.*lbf)



Hide 11301C 25.INSTALL TIMING CHAIN OR BELT COVER OIL SEAL

Hide 11321C 26.INSTALL TIMING GEAR COVER

Hide 13470 27.INSTALL CRANKSHAFT PULLEY ASSEMBLY

Hide 15104 28.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Install a new O-ring onto the cylinder block.


b.

Install the oil strainer sub-assembly with the 2 bolts.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)



Hide 12101 29.INSTALL OIL PAN SUB-ASSEMBLY

Hide 11351H 30.INSTALL FLYWHEEL HOUSING STAY RH

Hide 11351G 31.INSTALL FLYWHEEL HOUSING STAY LH

Hide 13751 32.INSTALL VALVE LIFTER

NOTICE:

Be sure to install the removed valve lifter in its original position.


Hide 11115 33.INSTALL CYLINDER HEAD GASKET

Hide 11101 34.INSTALL CYLINDER HEAD SUB-ASSEMBLY

Hide 13819 35.INSTALL VALVE BRIDGE

NOTICE:

Be sure to install the removed valve bridge to its original location.


Hide 13781 36.INSTALL VALVE PUSH ROD

NOTICE:

Be sure to install the removed valve push rod to its original location.


Hide 13901 37.INSTALL NO. 1 VALVE ROCKER SHAFT SUB-ASSEMBLY

Hide 38.ADJUST VALVE CLEARANCE

a.
A151510E08
0.134,0.081 0.36,0.251 0.227,0.17 10 *a 0.134,2.362 0.473,2.645 0.34,0.283 10 *b 2.713,1.397 2.892,1.569 0.178,0.172 10 *c 2.767,0.797 2.819,1.368 2.819,1.368 2.969,0.77 false 2.753,3.022 2.822,3.583 2.822,3.583 2.972,2.986 false 2.71,3.608 2.889,3.78 0.178,0.172 10 *c

Turn the crankshaft clockwise to align the alignment marks on the flywheel sub-assembly with the line between the 2 numbers on the edge on the flywheel housing.

Text in Illustration
*a TDC of No. 1 and No. 4 Cylinders
*b TDC of No. 2 and No. 3 Cylinders
*c Alignment Marks


b.
A462577C04
2.563,0.854 2.844,1.521 false 1.229,1.01 2.021,0.24 true 1.219,1.073 1.01,1.781 1.01,1.781 0.781,1.781 true 2.063,0.083 2.26,0.25 0.198,0.167 10 false *a 2.813,1.552 3.063,1.771 0.25,0.219 10 false *b 0.615,1.719 0.792,1.865 0.177,0.146 10 true *1
*1 Lock Nut
*a Adjusting Screw
*b Feeler Gauge


With the No. 1 piston positioned at TDC on the compression stroke, adjust each valve clearance using a feeler gauge.

Standard Valve Clearance (Cold):
Item Specified Condition
Intake 0.3 mm (0.0118 in.)
Exhaust 0.45 mm (0.0177 in.)


HINT:

The feeler gauge should move with a very slight pull.



c.

Loosen the lock nut on the valve rocker arm and loosen the adjusting screw.


d.

Insert a 0.30 mm (0.0118 in.) feeler gauge for the intake or a 0.45 mm (0.0177 in.) feeler gauge for the exhaust between the adjusting screw on the valve rocker arm and the valve bridge.


e.

Turn the adjusting screw on the valve rocker arm until the feeler gauge slides with a very slight drag, and lock the adjusting screw with the lock nut.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)



f.

Recheck the clearance.


g.

Adjust the other valves.

i.

Turn the crankshaft 1 revolution (360°) clockwise.


ii.

Adjust the valve clearance for each cylinder in the firing order.

Firing order:

1 - 3 - 4 - 2

(The cylinder number is counted from the timing gear side)