Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM C

N04C-VJ ENGINE CONTROL  ECD SYSTEM  P1674  Solenoid for Exhaust Brake Circuit Malfunction  


DESCRIPTION

The exhaust brake VSV, mounted on the exhaust retarder, opens and closes according to the signals from the ECM. The ECM receives the signals from the clutch switch and exhaust retarder switch. Through the brake VSV, the ECM controls the negative pressure applied to the diaphragm in the retarder.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1674 Solenoid for Exhaust Brake Circuit Malfunction Open or short in exhaust brake solenoid circuit for more than 3 seconds with clutch pedal released
(1 trip detection logic)
·

Open or short in exhaust brake solenoid circuit

·

Exhaust brake with bracket solenoid assembly

·

ECM


Does not come on DTC stored

WIRING DIAGRAM

A402321E07
0.583,2.396 0.896,2.594 0.313,0.198 10 false A4 0.573,2.573 2.344,2.948 1.771,0.375 10 false Exhaust Brake with Bracket Solenoid Assembly 5.938,2.771 6.417,3.01 0.479,0.24 10 false B102 5.948,2.938 6.333,3.125 0.385,0.188 10 false ECM 5.552,1.188 5.938,1.375 0.385,0.188 10 false EXB 5.563,1.906 6.042,2.104 0.479,0.198 10 false E01 5.313,1.073 5.469,1.271 0.156,0.198 10 false 8 5.313,1.771 5.583,1.958 0.271,0.188 10 false 11 2.063,1.083 2.219,1.281 0.156,0.198 10 false 1 2.063,1.781 2.219,1.979 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT EXHAUST BRAKE WITH BRACKET SOLENOID ASSEMBLY
a.

Inspect the exhaust brake with bracket solenoid assembly.

Click hereBrake>EXHAUST BRAKE>EXHAUST BRAKE RETARDER SOLENOID>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ECM - EXHAUST BRAKE WITH BRACKET SOLENOID ASSEMBLY)

NG

REPLACE EXHAUST BRAKE WITH BRACKET SOLENOID ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (ECM - EXHAUST BRAKE WITH BRACKET SOLENOID ASSEMBLY)
a.

Disconnect the exhaust brake with bracket solenoid assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-1 - B102-8 (EXB) Always Below 1 Ω
A4-1 or B102-8 (EXB) - Body ground Always 10 kΩ or higher



d.

Reconnect the exhaust brake with bracket solenoid assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR