Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM J

N04C-VJ ENGINE CONTROL  ECD SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly uses 5 V from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL is not illuminated even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to the ON position. The MIL goes off when the engine is started.


A224410E03
4.375,1.188 6.198,1.365 1.823,0.177 10 false 5 V Constant Voltage Circuit 5.354,2.052 6.365,2.469 1.01,0.417 10 false Microprocessor 1.26,1.135 2.656,1.333 1.396,0.198 10 false from EFI-MAIN Fuse 1.26,1.49 2.719,1.688 1.458,0.198 10 false from EFI NO. 2 Fuse 2.906,1 3.427,1.219 0.521,0.219 10 false BATT 0.302,2.01 2.594,2.552 2.292,0.542 10 false Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have IC) 0.375,2.948 2.656,3.323 2.281,0.375 10 false Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.073,3.125 4.333,3.333 0.26,0.208 10 false R 2.99,1.344 3.344,1.542 0.354,0.198 10 false +B 3.167,2.292 3.458,2.49 0.292,0.198 10 false VC 4.938,3.375 5.385,3.604 0.448,0.229 10 false ECM

WIRING DIAGRAM

A401960E03
0.708,1.385 1.167,1.583 0.458,0.198 10 false B18 0.708,1.552 3.417,1.906 2.708,0.354 10 false Manifold Absolute Pressure Sensor 2.417,0.406 2.875,0.604 0.458,0.198 10 false VC 2.385,0.75 2.844,0.948 0.458,0.198 10 false PIM 2.51,1.094 2.969,1.292 0.458,0.198 10 false E 2.75,0.313 3.198,0.469 0.448,0.156 10 false 3 2.75,0.667 3.198,0.823 0.448,0.156 10 false 2 2.74,1.01 3.188,1.167 0.448,0.156 10 false 1 5.219,0.74 5.677,0.938 0.458,0.198 10 false B104 5.333,0.563 5.802,1.25 0.469,0.688 10 false 5 5.229,2.635 5.688,2.833 0.458,0.198 10 false B104 5.219,4.292 5.677,4.49 0.458,0.198 10 false B104 5.229,5.01 5.688,5.208 0.458,0.198 10 false B104 0.115,3.271 0.573,3.469 0.458,0.198 10 false B27 0.104,3.479 4.219,4.01 4.115,0.531 10 false Throttle Position Sensor (Built into Diesel Throttle Body Assembly) 2.74,2.188 3.188,2.344 0.448,0.156 10 false 1 2.75,2.563 3.198,2.719 0.448,0.156 10 false 3 2.75,2.885 3.198,3.042 0.448,0.156 10 false 2 2.427,2.302 2.885,2.5 0.458,0.198 10 false VC 2.344,2.656 2.802,2.854 0.458,0.198 10 false VTA 2.448,3 2.906,3.198 0.458,0.198 10 false E2 5.677,2.667 6.323,2.896 0.646,0.229 10 false VTA1 5.667,0.771 6.125,0.969 0.458,0.198 10 false PIM 0.365,6.635 4.427,6.948 4.063,0.313 10 false Fuel Pressure Sensor (Built into Common Rail Assembly) 0.396,6.458 0.854,6.656 0.458,0.198 10 false B93 5.229,4.656 5.688,4.854 0.458,0.198 10 false B105 5.219,5.375 5.677,5.573 0.458,0.198 10 false B105 5.229,5.729 5.688,5.927 0.458,0.198 10 false B105 5.219,6.083 5.677,6.281 0.458,0.198 10 false B105 2.365,4.323 2.823,4.521 0.458,0.198 10 false VC1 2.292,4.688 2.75,4.885 0.458,0.198 10 false PCR1 2.458,5.021 2.917,5.219 0.458,0.198 10 false E1 2.448,5.396 2.906,5.594 0.458,0.198 10 false E2 2.271,5.75 2.729,5.948 0.458,0.198 10 false PCR2 2.354,6.104 2.813,6.302 0.458,0.198 10 false VC2 2.75,4.177 3.198,4.333 0.448,0.156 10 false 1 2.75,4.583 3.198,4.74 0.448,0.156 10 false 2 2.75,4.927 3.198,5.083 0.448,0.156 10 false 3 2.75,5.25 3.198,5.406 0.448,0.156 10 false 4 2.75,5.635 3.198,5.792 0.448,0.156 10 false 5 2.76,5.979 3.208,6.135 0.448,0.156 10 false 6 5.323,2.458 5.771,2.615 0.448,0.156 10 false 3 5.292,4.125 5.74,4.281 0.448,0.156 10 false 13 5.667,4.323 6.125,4.521 0.458,0.198 10 false VC 5.667,4.667 6.125,4.865 0.458,0.198 10 false PCR1 5.302,4.5 5.75,4.656 0.448,0.156 10 false 16 5.313,4.865 5.76,5.021 0.448,0.156 10 false 14 5.313,5.219 5.76,5.375 0.448,0.156 10 false 14 5.302,5.917 5.75,6.073 0.448,0.156 10 false 13 5.333,5.563 5.781,5.719 0.448,0.156 10 false 2 5.667,5.021 6.125,5.219 0.458,0.198 10 false E2 5.677,5.385 6.135,5.583 0.458,0.198 10 false E21 5.667,5.75 6.125,5.948 0.458,0.198 10 false PCR2 5.677,6.094 6.135,6.292 0.458,0.198 10 false VC2 4.156,7.146 4.615,7.344 0.458,0.198 10 false A 4.583,7.135 5.042,7.333 0.458,0.198 10 false B 5.927,7.156 6.563,7.573 0.635,0.417 10 false ECM

A261597E01
0.573,2.219 1.115,2.417 0.542,0.198 10 false A43 0.542,2.396 3.333,2.74 2.792,0.344 10 false Differential Pressure Sensor Assembly 0.594,4.354 1.24,4.594 0.646,0.24 10 false k2 0.583,4.542 2.469,4.885 1.885,0.344 10 false Camshaft Position Sensor 5.167,1.583 5.719,1.833 0.552,0.25 10 false B104 5.594,1.594 6.365,1.896 0.771,0.302 10 false PEX 5.167,3.031 5.635,3.292 0.469,0.26 10 false B103 5.573,3.052 6.094,3.396 0.521,0.344 10 false VCG 5.583,3.531 6,3.74 0.417,0.208 10 false G+ 5.604,4.021 5.969,4.25 0.365,0.229 10 false G- 0.26,7.74 0.844,7.99 0.583,0.25 10 false F9 0.26,7.896 5.031,8.365 4.771,0.469 10 false Accelerator Pedal Position Sensor (Built into Accelerator Link Assembly) 5.865,8.198 6.375,8.51 0.51,0.313 10 false ECM 2.333,1.25 2.823,1.417 0.49,0.167 10 false VC 2.354,1.958 2.865,2.167 0.51,0.208 10 false E2 2.292,1.604 3.271,1.833 0.979,0.229 10 false PEX 5.292,1.406 5.906,1.813 0.615,0.406 10 false 7 5.26,2.865 5.5,3.021 0.24,0.156 10 false 15 5.25,3.344 5.521,3.51 0.271,0.167 10 false 13 5.24,3.802 5.5,3.958 0.26,0.156 10 false 14 5.208,5.625 5.833,5.969 0.625,0.344 10 false A57 5.198,6.052 5.74,6.333 0.542,0.281 10 false A56 5.292,5.458 5.667,5.667 0.375,0.208 10 false 2 5.281,5.896 5.583,6.167 0.302,0.271 10 false 5 5.302,6.313 5.844,6.563 0.542,0.25 10 false 6 5.292,6.708 5.771,6.917 0.479,0.208 11 false 1 5.281,7.135 5.438,7.292 0.156,0.156 10 false 3 2.688,5.552 2.844,5.708 0.156,0.156 10 false 5 2.688,5.979 2.844,6.135 0.156,0.156 10 false 3 2.688,6.406 2.844,6.563 0.156,0.156 10 false 4 2.688,6.813 2.844,6.969 0.156,0.156 10 false 1 2.688,7.229 2.844,7.385 0.156,0.156 10 false 2 2.26,5.646 2.677,5.813 0.417,0.167 10 false VPA 2.281,6.063 2.823,6.25 0.542,0.188 10 false EPA 2.177,6.479 2.75,6.688 0.573,0.208 10 false VCPA 2.208,6.906 2.938,7.125 0.729,0.219 10 false VPA2 2.208,7.333 2.938,7.563 0.729,0.229 10 false EPA2 5.583,5.635 6.156,5.969 0.573,0.333 10 false VPA 5.594,6.052 6.083,6.271 0.49,0.219 10 false EPA 5.594,6.49 6.177,6.667 0.583,0.177 10 false VCPA 5.594,6.917 6.167,7.167 0.573,0.25 10 false VPA2 5.615,7.333 6.354,7.552 0.74,0.219 10 false EPA2 2.667,2.938 3.073,3.156 0.406,0.219 10 false 3 2.667,3.385 2.833,3.635 0.167,0.25 10 false 1 2.667,3.885 2.99,4.115 0.323,0.229 10 false 2 2.667,1.146 2.76,1.313 0.094,0.167 10 false 3 2.656,1.854 2.75,2.021 0.094,0.167 10 false 1 2.667,1.49 2.76,1.656 0.094,0.167 10 false 2 3.917,0.208 4.25,0.5 0.333,0.292 10 false A 4.365,0.219 4.677,0.5 0.313,0.281 10 false B 2.344,3.042 2.833,3.208 0.49,0.167 10 false VG 2.333,4.01 2.823,4.177 0.49,0.167 10 false G- 2.344,3.5 2.833,3.667 0.49,0.167 10 false G1 5.198,6.469 5.74,6.75 0.542,0.281 10 false A56 5.198,7.302 5.74,7.583 0.542,0.281 10 false A56 5.208,6.885 5.833,7.229 0.625,0.344 10 false A57 5.167,3.521 5.635,3.781 0.469,0.26 10 false B103 5.167,3.99 5.635,4.25 0.469,0.26 10 false B103

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK MIL
a.

Check that Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

OK:

MIL lights up.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK CONNECTION BETWEEN GTS AND ECM
2.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the tester and ECM.


Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

3.CHECK DIESEL THROTTLE BODY ASSEMBLY (CHECK MIL ILLUMINATED)

B

3.CHECK DIESEL THROTTLE BODY ASSEMBLY (CHECK MIL ILLUMINATED)
a.

Disconnect the throttle position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL is not illuminated A
MIL is illuminated B



d.

Reconnect the throttle position sensor connector.



A

4.CHECK ACCELERATOR LINK ASSEMBLY (CHECK MIL ILLUMINATED)

B

4.CHECK ACCELERATOR LINK ASSEMBLY (CHECK MIL ILLUMINATED)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL is not illuminated A
MIL is illuminated B



d.

Reconnect the accelerator pedal position sensor connector.



A

5.CHECK CAMSHAFT POSITION SENSOR (CHECK MIL ILLUMINATED)

B

5.CHECK CAMSHAFT POSITION SENSOR (CHECK MIL ILLUMINATED)
a.

Disconnect the camshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL is not illuminated A
MIL is illuminated B



d.

Reconnect the camshaft position sensor connector.



A

6.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR (CHECK MIL ILLUMINATED)

B

6.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR (CHECK MIL ILLUMINATED)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL is not illuminated A
MIL is illuminated B



d.

Reconnect the manifold absolute pressure sensor connector.



A

7.CHECK DIFFERENTIAL PRESSURE SENSOR (CHECK MIL ILLUMINATED)

B

7.CHECK DIFFERENTIAL PRESSURE SENSOR (CHECK MIL ILLUMINATED)
a.

Disconnect the differential pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL is not illuminated A
MIL is illuminated B



d.

Reconnect the differential pressure sensor connector.



A

8.CHECK COMMON RAIL ASSEMBLY (CHECK MIL ILLUMINATED)

B

8.CHECK COMMON RAIL ASSEMBLY (CHECK MIL ILLUMINATED)
a.

Disconnect the fuel pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL is not illuminated A
MIL is illuminated B



d.

Reconnect the fuel pressure sensor connector.



A

9.CHECK HARNESS AND CONNECTOR (ECM - EACH SENSOR)

B

REPLACE COMMON RAIL ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (ECM - EACH SENSOR)
a.

Disconnect the throttle position sensor connector.


b.

Disconnect the accelerator pedal position sensor connector.


c.

Disconnect the camshaft position sensor connector.


d.

Disconnect the manifold absolute pressure sensor connector.


e.

Disconnect the differential pressure sensor connector.


f.

Disconnect the fuel pressure sensor connector.


g.

Disconnect the ECM connectors.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A56-6 (VCPA) - Body ground Always 10 kΩ or higher
B103-15 (VCG) - Body ground Always 10 kΩ or higher
B104-13 (VC) - Body ground Always 10 kΩ or higher



i.

Reconnect the ECM connectors.


j.

Reconnect the fuel pressure sensor connector.


k.

Reconnect the differential pressure sensor connector.


l.

Reconnect the manifold absolute pressure sensor connector.


m.

Reconnect the camshaft position sensor connector.


n.

Reconnect the accelerator pedal position sensor connector.


o.

Reconnect the throttle position sensor connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR