Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM J

N04C-VJ ENGINE CONTROL  ECD SYSTEM  Abnormal Temperature Detection by Exhaust Temperature Sensor (Downstream)  


CAUTION / NOTICE / HINT

HINT:
·

If the exhaust temperature sensor detects an abnormally high temperature, conduct the following inspection.

·

Check the amount of engine oil after troubleshooting is finished.

·

If the amount of engine oil is more than the specified level, replace the engine oil.



PROCEDURE

1.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Inspect the air cleaner filter element sub-assembly.


Result:
Proceed to
OK
NG



OK

2.CHECK INTAKE SYSTEM

NG

REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

2.CHECK INTAKE SYSTEM
a.

Check for air leaks and blockage between the air cleaner and turbocharger sub-assembly.


b.

Check for air leaks and blockage between the turbocharger sub-assembly and intake manifold.


Result:
Proceed to
OK
NG



OK

3.PERFORM ENGINE RPM ACCELERATION

NG

REPAIR OR REPLACE INTAKE SYSTEM

3.PERFORM ENGINE RPM ACCELERATION
HINT:

If the exhaust gas contains excessive black smoke, perform the following operations:


a.

Warm up the engine.


b.

Disconnect the negative battery terminal and wait for at least 1 minute.


c.

Reconnect the negative battery terminal.


d.

Initialize the learning values of the injection or supply pump assembly (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

HINT:

Perform initialization with the engine warmed up (engine coolant temperature is 60°C (140°F) or more and fuel temperature is 20°C (68°F) or more).



e.

Initialize the learning values of the diesel throttle body assembly (Click here Engine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION.


f.

Accelerate the engine speed to the maximum rpm with no load 20 times.


g.

Check for black smoke in the exhaust gas.

OK:

Black smoke is not present.


HINT:

Soot deposits in the exhaust system may cause excessive black smoke.



Result:
Proceed to
OK
NG



OK

4.CHECK FUEL SYSTEM

NG

4.CHECK FUEL SYSTEM
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.


e.

Perform the Active Test with the engine idling.

Standard:
Item Condition Reference Value
Test the Fuel Leak With the engine speed at 2000 rpm in the Active Test, the fuel pressure in the common rail is set to (maintained at) 200000 kPa.
NOTICE:

Engine speed cannot be set by operating the accelerator pedal.


2000 rpm
(Fuel pressure 200000 kPa)
HINT:

If performed when cold, combustion may be unstable, but this is not a malfunction. Only check that the pressure increases to the target and that there is no fuel leak.




HINT:

Repair or replace if there is a malfunction.



f.

Check the fuel filter assembly for dirt or clogging.

HINT:

Repair or replace if there is a malfunction.



g.

After resolving the malfunction, proceed to the next step.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR ENGINE OIL LEAK
5.CHECK FOR ENGINE OIL LEAK
a.

Check that the intake system pipes and hoses are not excessively contaminated with oil.

HINT:
·

If the pipes or hoses are contaminated with oil, clean them.

·

If pipes or hoses are contaminated with a large amount of oil, repair or replace the parts and areas where the engine oil is leaking from.




b.

Check if the engine oil is leaking from the turbocharger subassembly.


Result:
Proceed to
NEXT



NEXT

6.READ VALUE USING GTS (DIFFERENTIAL PRESSURE)
6.READ VALUE USING GTS (DIFFERENTIAL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.




f.

After the forcible regeneration is completed, allow the engine to idle for at least 5 minutes.


g.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.


h.

Check the differential pressure when the exhaust gas temperature sensor indicates 200°C or less.

HINT:
·

If the exhaust gas temperature is high, the differential pressure cannot be measured correctly.

·

If the differential pressure is outside the normal range, the monolithic converter assembly may have deteriorated or the monolithic converter assembly may be clogged with PM.

·

Fully depress the accelerator pedal and when the engine speed becomes stable, promptly read the differential pressure.



Result:
Engine Speed (no engine load) Differential Pressure Proceed to
3500 to 3600 rpm (Exhaust gas temperature (up stream) is 200°C or less) Less than 15 kPa (MIL is not illuminated) A
15 kPa or more (MIL is not illuminated) B
MIL remains ON C




A

END

B

REPLACE CENTER EXHAUST PIPE ASSEMBLY

C