Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM C

N04C-VJ ENGINE CONTROL  ECD SYSTEM  P0087  Fuel Rail / System Pressure - Too Low  P0190  Fuel Rail Pressure Sensor Circuit  P0191  Fuel Rail Pressure Sensor Circuit Range / Performance  P0192  Fuel Rail Pressure Sensor Circuit Low Input  P0193  Fuel Rail Pressure Sensor Circuit High Input  


DESCRIPTION

The fuel pressure sensor, mounted on the common rail assembly, converts the fuel pressure into an electric signal and outputs the signal to the ECM. Based on the signal from the fuel pressure sensor, the ECM controls the injection or supply pump assembly (suction control valve) and keeps the internal fuel pressure of the common rail assembly at the target fuel pressure.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0087 Fuel Rail / System Pressure - Too Low Engine speed of 600 rpm or higher, 8 V or more, injection volume of 28 mm3/st or more, fuel pressure change is lower than malfunction judgment value, the predetermined amount of times(0.1 seconds or more in real time).
(1 trip detection logic):
·

Harness or connector

·

Fuel pressure sensor (built into common rail assembly)

·

ECM

·

ECM Power Source


Comes on DTC stored
P0190 Fuel Rail Pressure Sensor Circuit With ignition switch to ON, common rail assembly (fuel pressure sensor) output is 0.55 V or less or 4.9 V or more for 1 second or more.
(1 trip detection logic):
·

Harness or connector

·

Fuel pressure sensor (built into common rail assembly)

·

ECM


Comes on DTC stored
P0191 Fuel Rail Pressure Sensor Circuit Range / Performance Condition: The potential difference between circuit 1 and circuit 2 of the common rail assembly (fuel pressure sensor) exceeds the specified range continuously for 1 second.
(1 trip detection logic):
·

Harness or connector

·

Fuel pressure sensor (built into common rail assembly)

·

ECM


Comes on DTC stored
P0192 Fuel Rail Pressure Sensor Circuit Low Input Condition: Fuel pressure sensor output voltage is below 0.55 V continuously for 1 second or more.
(1 trip detection logic):
·

Harness or connector

·

Fuel pressure sensor (built into common rail assembly)

·

ECM


Comes on DTC stored
P0193 Fuel Rail Pressure Sensor Circuit High Input Condition Fuel pressure sensor output voltage is 4.9 V or high continues for 1 seconds or more
(1 trip detection logic):
·

Harness or connector

·

Fuel pressure sensor (built into common rail assembly)

·

ECM


Comes on DTC stored

HINT:
·

If the vehicle runs out of fuel, and the ECM determines that the fuel pressure has decreased, DTC P0190 or P0192 may be output.

·

When DTC P0087, P0190, P0191, P0192 and/or P0193 are stored, check the internal fuel pressure of the common rail assembly by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Fuel Press.


Fuel Pressure Malfunction
Approximately 0 kPa (0 kgf/cm2, 0 psi)
·

Short in PCR1 and E2 termina

·

Short in PCR2 and E21 terminal

·

Open in VC circuit

·

Open in VC2 circuit


Approximately 190000 kPa (1937 kgf/cm2, 27557 psi) or more
·

Short in PCR1 and VC circuit

·

Short in PCR2 and VC2 circuit

·

Open in PCR1 circuit

·

Open in PCR2 circuit

·

Open in E2 circuit

·

Open in E21 circuit




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0087 After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds
P0190
P0192
P0193
Ignition switch ON for 1 seconds or more
P0191 Idling for 1 second or more

WIRING DIAGRAM

A261579E03
1.708,0.917 2.042,1.083 0.333,0.167 10 false VC2 1.708,3.719 2.104,3.906 0.396,0.188 10 false VC1 1.635,1.49 2.073,1.646 0.438,0.156 10 false PCR2 1.625,3.167 2.063,3.344 0.438,0.177 10 false PCR1 1.813,2.042 2.177,2.198 0.365,0.156 10 false E2 1.813,2.604 2.094,2.76 0.281,0.156 10 false E1 5.927,0.927 6.281,1.146 0.354,0.219 10 false VC2 5.927,3.719 6.208,3.896 0.281,0.177 10 false VC 5.938,1.479 6.448,1.677 0.51,0.198 10 false PCR2 5.938,3.156 6.448,3.365 0.51,0.208 10 false PCR1 5.927,2.031 6.469,2.24 0.542,0.208 10 false E21 5.938,2.594 6.292,2.76 0.354,0.167 10 false E2 2.104,0.813 2.26,0.969 0.156,0.156 10 false 6 2.115,3.594 2.271,3.75 0.156,0.156 10 false 1 2.104,1.344 2.26,1.5 0.156,0.156 10 false 5 2.104,3.042 2.26,3.198 0.156,0.156 10 false 2 2.104,1.927 2.26,2.083 0.156,0.156 10 false 4 2.094,2.479 2.25,2.635 0.156,0.156 10 false 3 5.521,0.927 5.917,1.125 0.396,0.198 10 false B105 5.521,2.594 5.958,2.823 0.438,0.229 10 false B104 6.177,4.167 6.646,4.448 0.469,0.281 10 false ECM 0.677,4.156 1.24,4.344 0.563,0.188 10 false B93 0.667,4.313 4.042,4.563 3.375,0.25 10 false Common Rail Assembly (Fuel Pressure Sensor) 5.573,0.74 5.813,0.896 0.24,0.156 10 false 13 5.583,3.531 5.854,3.719 0.271,0.188 10 false 13 5.583,1.854 5.792,2.01 0.208,0.156 10 false 14 5.563,2.406 5.823,2.563 0.26,0.156 10 false 14 5.573,2.969 5.823,3.167 0.25,0.198 10 false 16 5.635,1.292 5.792,1.448 0.156,0.156 10 false 2 5.51,1.49 5.896,1.667 0.385,0.177 10 false B105 5.5,2.042 5.885,2.219 0.385,0.177 10 false B105 5.521,3.719 5.958,3.948 0.438,0.229 10 false B104 5.51,3.167 5.896,3.344 0.385,0.177 10 false B105

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read Current DTCs.


Result:
Result Proceed to
DTC P0087, P0190, P0191, P0192 or P0193 is output A
DTC P0087 is output B



A

2.INSPECT ECM (OUTPUT VOLTAGE)

B

REPLACE COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)

2.INSPECT ECM (OUTPUT VOLTAGE)
a.
A260250C06
1.302,0.104 1.792,0.396 0.49,0.292 1.844,0.104 2.333,0.396 0.49,0.292 2.24,0.875 2.917,1.729 true 2.177,0.875 2.333,1.74 true 1.75,0.875 1.677,1.719 true 1.677,0.875 1,1.74 true 1.396,0.167 1.813,0.323 0.417,0.156 10 false B105 1.938,0.167 2.417,0.323 0.479,0.156 10 false B104 0.063,0.073 0.25,0.281 0.188,0.208 10 false *a 1.479,1.76 2.115,2.031 0.635,0.271 10 false 13 (VC2) 2.729,1.76 3.427,2 0.698,0.24 10 false 13 (VC) 2.146,1.771 2.844,2.01 0.698,0.24 10 false 14 (E2) 0.771,1.771 1.406,2.042 0.635,0.271 10 false 14 (E21)
*a Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B104-13 (VC) - B104-14 (E2) Ignition switch ON 4.5 to 5.5 V
B105-13 (VC2) - B105-14 (E21) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (PCR VOLTAGE)

NG

3.INSPECT ECM (PCR VOLTAGE)
a.
A260250C07
1.302,0.104 1.792,0.396 0.49,0.292 1.844,0.104 2.333,0.396 0.49,0.292 2.188,0.865 2.917,1.729 true 1.688,0.875 2.271,1.76 true 1.521,0.875 0.49,1.75 true 1.688,0.719 1.302,1.74 true 1.396,0.167 1.813,0.323 0.417,0.156 10 false B105 1.938,0.167 2.417,0.323 0.479,0.156 10 false B104 0.063,0.073 0.25,0.281 0.188,0.208 10 false *a 1.042,1.76 1.677,2.031 0.635,0.271 10 false 2 (PCR2) 0.292,1.76 0.99,2 0.698,0.24 10 false 16 (PCR1) 2.729,1.771 3.427,2.01 0.698,0.24 10 false 14 (E2) 2.125,1.771 2.76,2.042 0.635,0.271 10 false 14 (E21)
*a Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B105-16 (PCR1) - B104-14 (E2) Idling 1.6 to 2.0 V
B105-2 (PCR2) - B105-14 (E21) Idling 1.1 to 1.5 V



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
4.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the fuel pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B105-16 (PCR1) - B93-2 (PCR1) Always Below 1 Ω
B104-13 (VC) - B93-1 (VC1) Always Below 1 Ω
B104-14 (E2) - B93-3 (E1) Always Below 1 Ω
B105-2 (PCR2) - B93-5 (PCR2) Always Below 1 Ω
B105-13 (VC2) - B93-6 (VC2) Always Below 1 Ω
B105-14 (E21) - B93-4 (E2) Always Below 1 Ω
B105-16 (PCR1) or B93-2 (PCR1) - Body ground Always 10 kΩ or higher
B104-13 (VC) or B93-1 (VC1) - Body ground Always 10 kΩ or higher
B105-2 (PCR2) or B93-5 (PCR2) - Body ground Always 10 kΩ or higher
B105-13 (VC2) or B93-6 (VC2) - Body ground Always 10 kΩ or higher
B104-14 (E2) or B93-3 (E1) - Other terminals Always 10 kΩ or higher
B105-14 (E21) or B93-4 (E2) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR