Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM C

N04C-VJ ENGINE CONTROL  ECD SYSTEM  P0006  Fuel Shutoff Valve "A" Control Circuit Low  P0007  Fuel Shutoff Valve "A" Control Circuit High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0006 Fuel Shutoff Valve "A" Control Circuit Low Conditions (a) and (b) continue for 2 second or more:
(1 trip detection logic)

(a) Ignition switch to ON

(b) Short in fuel addition cut valve assembly circuit


·

Harness or connector

·

Fuel addition cut valve assembly

·

ECM


Comes on DTC stored
P0007 Fuel Shutoff Valve "A" Control Circuit High Conditions (a) and (b) continue for 2 second or more:
(1 trip detection logic)

(a) Ignition switch to ON

(b) Open in fuel addition cut valve assembly circuit


·

Harness or connector

·

Fuel addition cut valve assembly

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0006 Ignition switch ON for 2 seconds or more
P0007 Ignition switch ON for 2 seconds or more after 20 seconds have elapsed after turning ignition switch OFF

WIRING DIAGRAM

A256054E07
4.469,0.813 4.625,0.969 0.156,0.156 10 false 6 2.021,0.906 2.99,1.104 0.969,0.198 10 false FCV 4.688,0.906 5.042,1.167 0.354,0.26 10 false FCV 4.656,2.063 5.833,2.438 1.177,0.375 10 false ECM 4.656,1.885 5.073,2.042 0.417,0.156 10 false B103 1.188,1.708 3.771,2.042 2.583,0.333 10 false Fuel Addition Cut Valve Assembly 2.427,0.813 2.583,0.969 0.156,0.156 10 false 2 1.188,1.531 1.698,1.719 0.51,0.188 10 false B156

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injection or supply pup assembly, the ECM needs initialization (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injector assembly, the ECM needs registration (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the ECM connector.


b.

Disconnect the fuel addition cut valve assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B103-6 (FCV) - B156-2 (+B) Always Below 1 Ω
B103-6 (FCV) or B156-2 (+B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT FUEL ADDITION CUT VALVE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

2.INSPECT FUEL ADDITION CUT VALVE ASSEMBLY
a.

Inspect the fuel addition cut valve assembly.

Click hereEngine / Hybrid System>N04C-VJ (FUEL)>FUEL ADDITION CUT VALVE ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE ECM

NG

REPLACE FUEL ADDITION CUT VALVE ASSEMBLY