Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM C

N04C-VJ ENGINE CONTROL  ECD SYSTEM  P2032  Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 2)  P2033  Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 2  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2032 Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 2) All of the following conditions are met:
(1 trip detection logic)

(a) Engine has been running for 30 minutes or more.

(b) Engine coolant temperature is 60°C (140°F) or higher.

(c) Injection volume is 40 mm3/st or more.

(d) Sensor 2 output is less than 0.1 V for 8 seconds or more.


·

No. 2 exhaust gas temperature sensor

·

Harness or connector

·

ECM


Comes on DTC stored
P2033 Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 2 All of the following conditions are met:
(1 trip detection logic)

(a) Engine has been running for 30 minutes or more.

(b) Engine coolant temperature is 60°C (140°F) or higher.

(c) Injection volume is 40 mm3/st or more.

(d) Sensor 2 output is more than 4.95 V for 8 seconds or more.


·

No. 2 exhaust gas temperature sensor

·

Harness or connector

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

·

The No. 2 exhaust gas temperature sensor consistently detects exhaust gas temperature.

·

A reading taken by the No. 2 exhaust gas temperature sensor is used to control DPR regeneration.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2032
P2033
Wait 30 minutes or more after starting, then drive the vehicle at an engine speed of 1000 rpm or higher with a coolant temperature of 70°C or more.

WIRING DIAGRAM

A261590E06
1.177,1.646 1.625,1.813 0.448,0.167 10 false A129 1.156,1.823 3.74,2.083 2.583,0.26 10 false No. 2 Exhaust Gas Temperature Sensor 2.458,0.594 2.615,0.75 0.156,0.156 10 false 1 4.344,0.531 4.563,0.708 0.219,0.177 10 false 10 4.333,1.031 4.563,1.188 0.229,0.156 10 false 14 4.26,1.219 4.635,1.406 0.375,0.188 10 false B104 4.26,0.729 4.635,0.938 0.375,0.208 10 false B103 4.667,0.729 5.135,0.906 0.469,0.177 10 false THO2 4.698,1.208 4.979,1.375 0.281,0.167 10 false E2 2.448,1.094 2.625,1.281 0.177,0.188 10 false 2 5.146,1.948 6.01,2.26 0.865,0.313 10 false ECM 2.042,0.719 2.406,0.917 0.365,0.198 10 false THG 2.146,1.219 2.396,1.438 0.25,0.219 10 false E2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (EXHAUST GAS TEMPERATURE B1S2)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S2.


e.

Read the value displayed on the tester.

Standard:

Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up), and varies after an engine speed of 3000 rpm is maintained for 1 minute.


Result:
Result Proceed to
0°C (32°F) (After warming up the engine) A
1000°C (1832°F) B
Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up), and varies after maintaining the engine speed of 3000 rpm for 1 minute after accelerating the engine from idling to 3000 rpm C


HINT:
·

If there is a open circuit, the GTS will indicate 0°C (32°F).

·

If there is an short circuit, the GTS will indicate 1000°C (1832°F).





A

2.READ VALUE USING GTS (OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (SHORT IN WIRE HARNESS)

C

2.READ VALUE USING GTS (OPEN IN WIRE HARNESS)
a.
A178585C13
1.531,3.083 1.969,3.323 0.438,0.24 1.396,4.396 1.583,4 true 1.958,4 2.104,4.406 true 0.677,1.688 0.875,1.865 0.198,0.177 10 false *1 2.625,1.771 2.917,1.948 0.292,0.177 10 false *2 0.667,2.99 0.927,3.219 0.26,0.229 10 false *a 1.615,3.135 2.021,3.302 0.406,0.167 10 false A129 1.292,4.438 1.771,4.635 0.479,0.198 10 false E2 2,4.438 2.344,4.615 0.344,0.177 10 false THG
*1 Exhaust Gas Temperature Sensor (bank 1 sensor 2)
*2 ECM
*a Front view of wire harness connector
(to Exhaust Gas Temperature Sensor (bank 1 sensor 2))


Disconnect the exhaust gas temperature sensor (bank1 sensor 2) connector.


b.

Connect terminals 1 and 2 of the exhaust gas temperature sensor wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S2.


g.

Read the value.

Standard:

1000°C (1832°F)



h.

Reconnect the exhaust gas temperature sensor connector.


Result:
Proceed to
OK
NG



OK

REPLACE EXHAUST GAS TEMPERATURE SENSOR (BANK 1 SENSOR 2)

NG

3.READ VALUE USING GTS (OPEN IN ECM)
3.READ VALUE USING GTS (OPEN IN ECM)
a.
A178586C10
1.844,2.979 2.281,3.24 0.438,0.26 2.365,2.979 2.802,3.24 0.438,0.26 2.177,3.656 2,4.333 true 2.406,3.583 2.719,4.333 true 0.76,1.792 0.948,1.938 0.188,0.146 10 false *1 2.594,1.781 2.844,1.969 0.25,0.188 10 false *2 0.479,2.958 0.656,3.125 0.177,0.167 10 false *a 2.469,4.385 3.094,4.563 0.625,0.177 10 false 10(THO2) 1.823,4.385 2.24,4.563 0.417,0.177 10 false 14(E2) 1.917,3.031 2.375,3.219 0.458,0.188 10 false B104 2.438,3.042 2.885,3.229 0.448,0.188 10 false B103
*1 Exhaust Gas Temperature Sensor (bank 1 sensor 2)
*2 ECM
*a Component with harness connected
(ECM)


Disconnect the exhaust gas temperature sensor (bank1 sensor 2) connector.


b.

Connect terminals THO2 and E2 of the ECM connectors.

HINT:

Before checking, do a visual and contact pressure check on the ECM connector.



c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S2.


g.

Read the value.

Standard:

1000°C (1832°F)



h.

Reconnect the exhaust gas temperature sensor connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - EXHAUST GAS TEMPERATURE SENSOR)

NG

4.READ VALUE USING GTS (SHORT IN WIRE HARNESS)
a.
A302633C58
2.469,1.063 2.917,1.323 0.448,0.26 10 false THO2 2.479,1.51 3,1.708 0.521,0.198 10 false E2 0.771,0.25 1.083,0.448 0.313,0.198 10 false *1 2.583,0.25 2.896,0.448 0.313,0.198 10 false *2
*1 Exhaust Gas Temperature Sensor (bank 1 sensor 2)
*2 ECM


Disconnect the exhaust gas temperature sensor (bank1 sensor 2) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Exhaust Temperature B1S2.


f.

Read the value.

Standard:

0°C (32°F)



g.

Reconnect the exhaust gas temperature sensor connector.


Result:
Proceed to
OK
NG



OK

REPLACE EXHAUST GAS TEMPERATURE SENSOR (BANK 1 SENSOR 2)

NG

5.CHECK HARNESS AND CONNECTOR (ECM - EXHAUST GAS TEMPERATURE SENSOR)
5.CHECK HARNESS AND CONNECTOR (ECM - EXHAUST GAS TEMPERATURE SENSOR)
a.

Disconnect the exhaust gas temperature sensor (bank1 sensor 2) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B103-10 (THO2) - B129-1 (THG) Always Below 1 Ω
B104-14 (E21) - A129-2 (E2) Always Below 1 Ω
B103-10 (THO2) or B129-1 (THG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - EXHAUST GAS TEMPERATURE SENSOR)