Home › Engine / Hybrid System › N04C-VJ (ENGINE CONTROL) › ECD SYSTEM › from 2021.01
RM2850E _51 Engine / Hybrid System _096807 N04C-VJ ENGINE CONTROL _0454116 ECD SYSTEM C

N04C-VJ ENGINE CONTROL  ECD SYSTEM  P0130  Oxygen Sensor Circuit (Bank 1 Sensor 1)  P2200  NOx Sensor Circuit Bank 1 Sensor 1  P2205  NOx Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)  


DESCRIPTION

The nitrogen oxides sensor is installed behind the DPR catalytic converter.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0130 Oxygen Sensor Circuit (Bank 1 Sensor 1) Diagnosis Condition:
·

Ignition switch ON


Malfunction Status:
·

A lambda sensor malfunction signal is output in the nitrogen oxides sensor


Malfunction Duration:
·

4.2 seconds or more


·

ECM

·

Harness or connector

·

Nitrogen oxides sensor


Comes on DTC stored
P2200 NOx Sensor Circuit Bank 1 Sensor 1 Diagnosis Condition:
·

Ignition switch ON


Malfunction Status:
·

A NOx sensor malfunction signal is output in the nitrogen oxides sensor


Malfunction Duration:
·

4.2 seconds or more


·

ECM

·

Harness or connector

·

Nitrogen oxides sensor


Comes on DTC stored
P2205 NOx Sensor Heater Circuit Malfunction (Bank 1 Sensor 1) Diagnosis Condition:
·

Ignition switch ON


Malfunction Status:
·

A NOx sensor heater malfunction signal is output in the nitrogen oxides sensor


Malfunction Duration:
·

4.2 seconds or more


·

ECM

·

Harness or connector

·

Nitrogen oxides sensor


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0130
P2200
P2205
Idling after engine warm-up

WIRING DIAGRAM

A483980E04
1.854,0.563 2.5,0.771 0.646,0.208 10 false EFI NO.1 1.094,0.563 1.823,0.771 0.729,0.208 10 false EFI-MAIN 0.604,0.573 1.083,0.781 0.479,0.208 10 false P/I 0.385,1.302 1.25,1.51 0.865,0.208 10 false R/B NO.2-B 0.458,3.51 1,3.719 0.542,0.208 10 false ALT 0.344,4.24 1.115,4.438 0.771,0.198 10 false FL MAIN 2.51,3.469 2.875,3.708 0.365,0.24 10 false AM1 0.49,5.063 1.125,5.281 0.635,0.219 10 false Battery 4.74,3.698 5.156,3.885 0.417,0.188 10 false J63 4.719,3.875 7.021,4.073 2.302,0.198 10 false Ignition Switch Assembly 4.698,3.208 4.958,3.417 0.26,0.208 10 false 6 3.656,3.125 3.917,3.333 0.26,0.208 10 false 27 5.521,3.219 5.781,3.427 0.26,0.208 10 false IG1 4.875,3.219 5.229,3.427 0.354,0.208 10 false AM1 2.302,2.677 2.948,2.885 0.646,0.208 10 false IG2-NO.2 2.656,1.063 3.302,1.271 0.646,0.208 10 false NOX SSR 3.323,0.25 3.51,0.417 0.188,0.167 10 false 5 3.313,0.677 3.5,0.844 0.188,0.167 10 false 1 2.542,0.25 2.729,0.417 0.188,0.167 10 false 3 5.104,0.167 5.292,0.333 0.188,0.167 10 false 2 4.104,0.24 4.292,0.406 0.188,0.167 10 false 5 3.542,1.365 3.729,1.531 0.188,0.167 10 false 15 4.281,0.365 4.594,0.531 0.313,0.167 10 false +B 4.281,1.073 4.698,1.25 0.417,0.177 10 false GND 4.177,1.365 4.594,1.542 0.417,0.177 10 false A131 4.177,1.51 5.24,1.708 1.063,0.198 10 false Nitrogen Oxides Sensor 4.635,0.365 5.052,0.542 0.417,0.177 10 false CANH 4.635,0.979 5.052,1.156 0.417,0.177 10 false CANL 2.552,0.667 2.74,0.833 0.188,0.167 10 false 2 5.125,0.802 5.313,0.969 0.188,0.167 10 false 3 5.76,0.354 6.177,0.531 0.417,0.177 10 false B104 5.76,0.969 6.177,1.146 0.417,0.177 10 false B104 5.833,0.135 6.021,0.302 0.188,0.167 10 false 12 5.865,0.771 6.052,0.938 0.188,0.167 10 false 6 6.188,0.365 6.604,0.542 0.417,0.177 10 false CAN+ 6.198,0.979 6.615,1.156 0.417,0.177 10 false CAN- 6.396,1.469 6.813,1.646 0.417,0.177 10 false ECM 5.833,3.208 6.094,3.417 0.26,0.208 10 false 5 3.188,4.802 4.927,5.042 1.74,0.24 10 false : CAN communication line 3.656,3.323 4.021,3.563 0.365,0.24 10 false 4D 3.656,2.385 4.021,2.625 0.365,0.24 10 false 4A 3.656,1.573 4.021,1.813 0.365,0.24 10 false 4F 1.802,1.948 2.167,2.188 0.365,0.24 10 false 4L 1.802,2.385 2.167,2.625 0.365,0.24 10 false 4D 1.802,3.323 2.167,3.563 0.365,0.24 10 false 4K 4.115,0.948 4.302,1.115 0.188,0.167 10 false 4 3.656,2.188 3.844,2.354 0.188,0.167 10 false 17 1.854,3.135 2.042,3.302 0.188,0.167 10 false 1 1.854,2.208 2.042,2.375 0.188,0.167 10 false 3 1.844,1.729 2.031,1.896 0.188,0.167 10 false 1 1.854,3.917 4.76,4.281 2.906,0.365 10 false Instrument Panel Junction Block 0.458,2.094 1,2.302 0.542,0.208 10 false J/B-B 1.083,3.5 1.625,3.708 0.542,0.208 10 false J/B ALT 3.052,2.083 3.698,2.292 0.646,0.208 10 false IGN NO.3

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the injector assembly, the ECM needs registration (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).

·

After replacing the suction control valve or supply pump assembly, the ECM needs initialization (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION) and initialization (Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT NITROGEN OXIDES SENSOR
a.
A394581C02
1.521,0.365 1.906,0.604 0.385,0.24 2.615,1.635 2.229,1.167 true 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 1.573,0.406 2.323,0.563 0.75,0.156 10 false A131 2.583,1.677 2.896,1.875 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Nitrogen Oxides Sensor)


Disconnect the nitrogen oxides sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A131-5 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR

NG

6.INSPECT RELAY (NOX SSR RELAY)
2.CHECK HARNESS AND CONNECTOR
a.

Disconnect the nitrogen oxides sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A131-4 (GND) - Body ground and other terminals Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

3.REPLACE NITROGEN OXIDES SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE NITROGEN OXIDES SENSOR
a.

Replace the nitrogen oxides sensor.

Click hereEngine / Hybrid System>N04C-VJ (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL

Result:
Proceed to
NEXT




NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Connect the GTS to DLC3.



Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS
5.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P0130, P2200 and/or P2205 are output A
DTC is not output B




A

B

END

6.INSPECT RELAY (NOX SSR RELAY)

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (NOX SSR RELAY - NITROGEN OXIDES SENSOR)

NG

REPAIR OR REPLACE NOX SSR RELAY

7.CHECK HARNESS AND CONNECTOR (NOX SSR RELAY - NITROGEN OXIDES SENSOR)
a.

Disconnect the nitrogen oxides sensor connector.


b.

Remove the NOX SSR relay from the No. 2 relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
5 (NOX SSR relay holder) - A131-5 (+B) Always Below 1 Ω


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (ECM - INSTRUMENT PANEL JUNCTION BLOCK - IGNITION SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR (NOX SSR RELAY - NITROGEN OXIDES SENSOR)