Home › Engine / Hybrid System › N04C-VJ (FUEL) › COMMON RAIL › from 2021.01
RM2850E _51 Engine / Hybrid System _096891 N04C-VJ FUEL _0461604 COMMON RAIL A

N04C-VJ FUEL  COMMON RAIL  INSTALLATION  


PROCEDURE

Hide 23810A 1.INSTALL COMMON RAIL ASSEMBLY

a.
A257607

Install the common rail assembly and common rail assembly fuel pipe support with the 2 bolts.

Torque:
55 N*m (561 kgf*cm, 41 ft.*lbf)


b.
A257603

Connect the No. 4 fuel pipe and a new gasket with the union bolt.

Torque:
20.1 N*m (205 kgf*cm, 15 ft.*lbf)


c.
A260330

Temporarily install the fuel pipe support with the 2 bolts.


d.

Connect the fuel pressure sensor connector.


Hide 2.INSTALL INJECTION PIPE SUB-ASSEMBLY

a.

Temporarily install the injection pipe sub-assembly with the 8 union nuts.


b.

Using a 17 mm union nut wrench, tighten the 8 union nuts.

Torque:
Specified tightening torque:

35 N*m (357 kgf*cm, 26 ft.*lbf)


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

·
A342275C04
0.677,0.74 0.865,0.917 0.188,0.177 10 true *a
*a Torque Wrench Fulcrum Length


When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




Hide 23802E 3.INSTALL FUEL PIPE SUB-ASSEMBLY

a.

Using a 17 mm union nut wrench, install the fuel pipe sub-assembly with the union nut.

Torque:
Specified tightening torque:

35 N*m (357 kgf*cm, 26 ft.*lbf)


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

·
A342276C01
1.271,0.26 1.583,0.458 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)




b.

Install the 2 fuel pipe clamps with the 2 nuts.

HINT:

Tighten the nut until the clamp edge makes contact with the engine side clamp edge.



Hide 23849G 4.INSTALL FUEL PIPE SUPPORT

a.

Tighten the fuel pipe support with the 2 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


Hide 23741B 5.INSTALL INJECTION PIPE CLAMP

a.
A257835

Install the 2 injection pipe clamps with the 2 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


b.

Connect the connector and clamp.


Hide 25608 7.INSTALL EGR COOLER SUB-ASSEMBLY

Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)