Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0230  Fuel Pump Primary Circuit  


DESCRIPTION

When the engine is cranked, a signal is sent from the ignition control ECU's STSW terminal to the ECM's STSW terminal. Then voltage travels from the ECM's STAR terminal through the park/neutral position switch to the STARTER relay coil. The STAR terminal also sends a signal to the STA terminal. When the STA signal and NE signal are input to the ECM, the ECM interior's Tr1 turns on, which causes power to be supplied to the C/OPN relay coil (C/OPN on). As a result, the F/PMP relay actuates, which causes the fuel pump to operate. If the engine is operating and NE signals are being output, the ECM interior's Tr1 is on (C/OPN on), and the fuel pump will continue operating. The fuel pump's has a high and low speed setting. When the engine is starting or operating with a heavy load, the ECM interior's Tr2 turns on to actuate the F/PMP relay so that the fuel pump operates at the high speed setting. When the engine is idling or operating with a light load, the Tr2 turns off, and current flows through the fuel pump resister to the fuel pump so that the fuel pump operates at the low speed setting.

A285188E02
0.5,4.708 1.167,4.885 0.667,0.177 10 false F/B BATT 0.5,5.156 1.167,5.333 0.667,0.177 10 false FL MAIN 0.604,5.875 1.271,6.052 0.667,0.177 10 false Battery 4.229,4.927 5.26,5.104 1.031,0.177 10 false From ST Relay 3.115,5.323 5.313,5.583 2.198,0.26 10 false From Crankshaft Position Sensor 5.677,4.833 6.115,5.01 0.438,0.177 10 false STA 6.292,6.104 6.729,6.281 0.438,0.177 10 false ECM 5.563,4.417 6,4.594 0.438,0.177 10 false MREL 5.656,2.208 6.094,2.385 0.438,0.177 10 false FPR 5.75,0.396 6.188,0.573 0.438,0.177 10 false FC 6.417,1.177 6.854,1.354 0.438,0.177 10 false Tr 1 6.042,2.208 6.479,2.385 0.438,0.177 10 false Tr 2 5.677,5.24 6.115,5.417 0.438,0.177 10 false NE+ 5.115,1.604 5.781,1.781 0.667,0.177 10 false F/PMP 4.865,2.604 5.75,2.99 0.885,0.385 10 false Fuel Pump Resistor 4.813,3.427 5.698,3.646 0.885,0.219 10 false Fuel Pump 3.667,1.021 4.333,1.198 0.667,0.177 10 false C/OPN 1.677,1.833 1.969,2.01 0.292,0.177 10 false IG2 2.594,2.25 2.885,2.427 0.292,0.177 10 false IG2 1.688,0.635 1.979,0.813 0.292,0.177 10 false IGN 1.073,3.729 1.781,3.906 0.708,0.177 10 false AM2 No. 2 1.865,3.198 2.281,3.375 0.417,0.177 10 false AM2 1.542,4.406 1.958,4.583 0.417,0.177 10 false EFI 2.479,4.833 3.281,5.01 0.802,0.177 10 false EFI MAIN 1.906,2.625 2.323,2.802 0.417,0.177 10 false IG2D 1.875,2.958 2.292,3.135 0.417,0.177 10 false AM1 2.365,2.802 3.094,3.208 0.729,0.406 10 false Main Body ECU

DTC No. DTC Detection Condition Trouble Area
P0230 Open or short in F/PMP relay circuit (1 trip detection logic)
·

Open or short in F/PMP relay circuit

·

F/PMP relay

·

ECM



WIRING DIAGRAM

A159629E04
5.573,6.25 5.813,6.427 0.24,0.177 10 false A7 5.635,6.063 5.927,6.24 0.292,0.177 10 false 7 3.26,1.854 3.552,2.031 0.292,0.177 10 false 3 2.802,2.531 3.24,2.708 0.438,0.177 10 false IG2 5.313,2.635 5.75,2.813 0.438,0.177 10 false IGN 3.26,2.115 3.552,2.292 0.292,0.177 10 false 1 2.49,1.854 2.781,2.031 0.292,0.177 10 false 5 2.49,2.115 2.781,2.292 0.292,0.177 10 false 2 3.26,2.99 3.552,3.167 0.292,0.177 10 false 3 2.615,3.667 3.281,3.844 0.667,0.177 10 false EFI MAIN 3.26,3.25 3.552,3.427 0.292,0.177 10 false 1 2.49,2.99 2.781,3.167 0.292,0.177 10 false 5 2.49,3.25 2.781,3.427 0.292,0.177 10 false 2 4.5,4.844 4.688,5.021 0.188,0.177 10 false 5 3.948,5.51 4.615,5.688 0.667,0.177 10 false C/OPN 4.5,5.104 4.688,5.281 0.188,0.177 10 false 1 3.74,4.844 4.031,5.021 0.292,0.177 10 false 3 3.74,5.104 4.031,5.281 0.292,0.177 10 false 2 3.344,4.583 3.5,4.76 0.156,0.177 10 false 3 3.042,4.271 3.198,4.448 0.156,0.177 10 false 4 2.792,5.219 3.458,5.396 0.667,0.177 10 false F/PMP 1.208,3.25 1.521,3.427 0.313,0.177 10 false EFI 1.208,2.125 1.521,2.302 0.313,0.177 10 false IG2 0.979,0.813 1.719,0.99 0.74,0.177 10 false AM2 No. 2 0.625,3.76 1.292,3.938 0.667,0.177 10 false F/B BATT 0.625,4.406 1.292,4.583 0.667,0.177 10 false FL MAIN 0.729,6.094 1.396,6.271 0.667,0.177 10 false Battery 1.844,5.302 2.438,5.833 0.594,0.531 10 false A11 Fuel Pump Resistor 1.542,7.292 2.563,7.469 1.021,0.177 10 false M17 Fuel Pump 4.073,7.031 5.385,7.208 1.313,0.177 10 false From ST Relay 2.948,7.615 5.063,7.792 2.115,0.177 10 false From Crankshaft Position Sensor 3.344,4.844 3.5,5.021 0.156,0.177 10 false 2 2.573,4.583 2.865,4.76 0.292,0.177 10 false 5 2.573,4.844 2.865,5.021 0.292,0.177 10 false 1 1.542,5.146 1.833,5.323 0.292,0.177 10 false 1 1.542,5.802 1.833,5.979 0.292,0.177 10 false 2 1.25,6.958 1.542,7.135 0.292,0.177 10 false 4 1.25,7.604 1.542,7.781 0.292,0.177 10 false 5 5.896,6.208 6.146,6.385 0.25,0.177 10 false FC 5.573,3.396 5.813,3.573 0.24,0.177 10 false A7 5.583,3.188 5.875,3.365 0.292,0.177 10 false 44 5.896,3.344 6.333,3.521 0.438,0.177 10 false MREL 5.573,6.656 5.813,6.833 0.24,0.177 10 false D1 5.594,6.469 5.885,6.646 0.292,0.177 10 false 59 5.896,6.615 6.208,6.792 0.313,0.177 10 false FPR 5.573,7.052 5.813,7.229 0.24,0.177 10 false A7 5.594,6.865 5.885,7.042 0.292,0.177 10 false 48 5.896,7.021 6.188,7.198 0.292,0.177 10 false STA 5.573,7.469 5.813,7.646 0.24,0.177 10 false D1 5.542,7.271 5.833,7.448 0.292,0.177 10 false 110 5.896,7.427 6.208,7.604 0.313,0.177 10 false NE+ 5.573,7.875 5.813,8.052 0.24,0.177 10 false D1 5.542,7.656 5.833,7.833 0.292,0.177 10 false 111 5.896,7.833 6.167,8.01 0.271,0.177 10 false NE- 6.177,8.281 6.615,8.458 0.438,0.177 10 false ECM 2.667,1.458 3.896,1.635 1.229,0.177 10 false Main Body ECU 2.323,0.688 2.667,0.865 0.344,0.177 10 false G58 2.406,0.469 2.698,0.646 0.292,0.177 10 false 1 3.74,0.698 4.083,0.875 0.344,0.177 10 false G58 3.792,0.469 4.083,0.646 0.292,0.177 10 false 11 2.323,1.167 2.667,1.344 0.344,0.177 10 false G57 2.677,0.656 3.094,0.833 0.417,0.177 10 false AM2 3.313,0.656 3.729,0.833 0.417,0.177 10 false IG2D 2.677,1.125 3.094,1.302 0.417,0.177 10 false AM1 2.406,0.948 2.698,1.125 0.292,0.177 10 false 6

CAUTION / NOTICE / HINT

HINT:

This troubleshooting procedure is based on the premise that the engine is started. If the engine is not started, proceed to the problem symptoms table (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).


PROCEDURE

1.CHECK TERMINAL VOLTAGE (F/PMP RELAY POWER SOURCE)
a.

Remove the F/PMP relay from the engine room No. 1 relay block.


A159639E01
0.189,0.159 2.215,0.333 2.026,0.174 10 Engine Room No. 1 Relay Block 0.257,2.238 1.112,2.566 0.855,0.327 10 F/PMP Relay Holder

b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
F/PMP relay holder terminal (2) - Body ground STA signal ON 11 to 14 V
F/PMP relay holder terminal (2) - Body ground STA signal OFF Below 3 V




OK

2.INSPECT RELAY (Marking: F/PMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (F/PMP RELAY - C/OPN RELAY)

2.INSPECT RELAY (Marking: F/PMP)
a.
A087121E50
2.333,0.604 2.333,0.292 false 2.49,1.135 2.958,1.135 false 2.49,1.635 2.958,1.635 false 2.031,0.625 1.854,0.313 false 2.625,0.625 2.802,0.313 false 0.313,1.417 0.51,1.625 0.198,0.208 10 false 1 1.792,0.104 1.99,0.313 0.198,0.208 10 false 1 1.313,1.417 1.51,1.625 0.198,0.208 10 false 2 2.792,0.104 2.99,0.313 0.198,0.208 10 false 2 0.313,0.865 0.51,1.073 0.198,0.208 10 false 3 3.01,1.552 3.208,1.76 0.198,0.208 10 false 3 0.938,0.385 1.135,0.594 0.198,0.208 10 false 4 2.302,0.104 2.5,0.313 0.198,0.208 10 false 4 1.313,0.865 1.51,1.073 0.198,0.208 10 false 5 3.01,1.042 3.208,1.25 0.198,0.208 10 false 5

Remove the F/PMP relay from the engine room No. 1 relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
3 - 4 Below 1 Ω
3 - 4 10 kΩ or higher
(when battery voltage applied to terminals 1 and 2)
3 - 5 10 kΩ or higher
3 - 5 Below 1 Ω
(when battery voltage applied to terminals 1 and 2)




OK

3.CHECK HARNESS AND CONNECTOR (F/PMP RELAY - ECM)

NG

REPLACE RELAY

3.CHECK HARNESS AND CONNECTOR (F/PMP RELAY - ECM)
a.

Remove the F/PMP relay from the engine room No. 1 relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
F/PMP relay holder terminal (1) - D1-59 (FPR) Always Below 1 Ω
F/PMP relay holder terminal (1) or D1-59 (FPR) - Body Ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR