Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0560  System Voltage  


DESCRIPTION

The battery supplies electricity to the ECM even when the engine switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM will illuminate the MIL and stores the DTC.

DTC No. DTC Detection Condition Trouble Area
P0560 Open in ECM back-up power source circuit (1 trip detection logic).
·

Open in back-up power source circuit

·

Battery

·

Battery terminals

·

ECM



HINT:

If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is party cleared.


WIRING DIAGRAM

A159620E02
5.438,1.51 5.667,1.677 0.229,0.167 10 false A7 5.719,1.375 6.115,1.542 0.396,0.167 10 false BATT 1.292,3.729 1.771,3.896 0.479,0.167 10 false Battery 1.167,2.469 1.771,2.635 0.604,0.167 10 false FL MAIN 1.365,1.667 2.042,1.833 0.677,0.167 10 false F/B BATT 2.875,1.667 3.125,1.833 0.25,0.167 10 false EFI 6.01,3.615 6.375,3.781 0.365,0.167 10 false ECM 5.438,1.302 5.667,1.469 0.229,0.167 10 false 20 5.438,2.771 5.667,2.938 0.229,0.167 10 false D1 5.719,2.75 5.927,2.917 0.208,0.167 10 false E1 5.438,2.573 5.667,2.74 0.229,0.167 10 false 81

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After turning engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.INSPECT BATTERY
a.

Inspect that the battery is not depleted.

OK:

Battery is not depleted.




OK

2.CHECK BATTERY TERMINAL

NG

REPLACE BATTERY

2.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.




OK

3.CHECK HARNESS AND CONNECTOR (BATT TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE BATTERY TERMINAL

3.CHECK HARNESS AND CONNECTOR (BATT TERMINAL VOLTAGE)
a.
U188511E01
0.032,0.05 0.938,0.685 0.906,0.635 10 Wire Harness Side: 0.579,1.104 0.843,1.286 0.264,0.181 10 A25 1.094,1.937 1.467,2.084 0.373,0.147 10 BATT 1.474,1.125 1.324,1.93 false

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-20 (BATT) - Body ground Always 11 to 14 V




OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0560)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0560)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.



d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Turn the tester off.


f.

Start the engine and turn the tester on.


g.

Enter the following menus: Powertrain / Engine / DTC.


h.

Read the DTCs.

Result
Result Proceed to
DTC P0560 is output A
DTC is not output B



A

B