Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P2118  Throttle Actuator Control Motor Current Range / Performance  


DESCRIPTION

The electronic throttle control system has a dedicated power supply circuit. The voltage (+BM) is monitored and when it is low (less than 4 V), the ECM determines that there is a malfunction in the electronic throttle control system and cuts off the current to the throttle actuator.

When the voltage becomes unstable, the electronic throttle control system itself becomes unstable. For this reason, when the voltage is low, the current to the throttle actuator is cut. If repairs are made and the system returns to normal, turn the engine switch off. The ECM then allows the current to flow to the throttle actuator so that it can be restarted.

HINT:

The electronic throttle control system does not use a throttle cable.


A112629E05
0.24,1.665 0.840,2.045 0.600,0.380 10 From Battery 0.285,2.66 0.859,3.025 0.574,0.365 10 Throttle Actuator 1.207,1.637 1.677,1.839 0.470,0.202 10 ETC-S 5.609,0.199 6.059,0.401 0.450,0.202 10 ECM 4.761,1.693 5.211,1.895 0.450,0.202 10 +BM 4.761,3.753 5.278,3.955 0.517,0.202 10 ME01 4.761,2.422 5.078,2.624 0.317,0.202 10 M+ 4.761,3.066 5.078,3.268 0.317,0.202 10 M- 5.934,2.472 6.534,3.190 0.600,0.718 10 Throttle Actuator Control Circuit 4.761,0.917 5.211,1.119 0.450,0.202 10 +B 0.065,0.936 0.846,1.338 0.782,0.401 10 From EFI MAIN Relay 5.934,0.747 6.477,1.466 0.542,0.718 10 Power Source Circuit for CPU

DTC No. DTC Detection Condition Trouble Area
P2118 Open in electronic throttle control system power source (+BM) circuit
(1 trip detection logic)
·

Open in electronic throttle control system power source circuit

·

Battery

·

Battery terminals


·

ETC-S fuse


·

ECM



FAIL-SAFE

When any of these DTCs or other DTCs relating to Electronic Throttle Control System (ETCS) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the engine switch is then turned off.

WIRING DIAGRAM

A159624E02
4.574,1.939 4.795,2.109 0.221,0.170 10 D1 4.873,1.835 5.094,2.004 0.221,0.170 10 M+ 2.886,1.846 3.107,2.016 0.221,0.170 10 M+ 4.574,1.767 4.795,1.937 0.221,0.170 10 19 4.574,1.301 4.795,1.471 0.221,0.170 10 A7 4.873,1.224 5.182,1.394 0.309,0.170 10 +BM 4.623,1.129 4.844,1.298 0.221,0.170 10 3 4.574,2.773 4.795,2.943 0.221,0.170 10 D1 4.873,2.668 5.094,2.838 0.221,0.170 10 M- 2.886,2.689 3.107,2.859 0.221,0.170 10 M- 3.166,1.846 3.387,2.016 0.221,0.170 10 2 3.166,2.689 3.387,2.859 0.221,0.170 10 1 4.574,2.6 4.795,2.770 0.221,0.170 10 18 4.574,3.373 4.795,3.543 0.221,0.170 10 D1 4.873,3.373 5.321,3.543 0.448,0.170 10 GE01 4.574,3.201 4.795,3.370 0.221,0.170 10 41 4.574,3.92 4.795,4.089 0.221,0.170 10 D1 4.873,3.92 5.099,4.089 0.225,0.170 10 E1 4.574,3.747 4.795,3.917 0.221,0.170 10 81 4.574,4.429 4.795,4.598 0.221,0.170 10 D1 4.873,4.429 5.293,4.598 0.420,0.170 10 ME01 2.372,3.17 3.417,3.324 1.045,0.154 10 Throttle Actuator 1.069,2.138 1.711,2.291 0.642,0.154 10 F/B BATT 1.639,1.459 2.142,1.612 0.503,0.153 10 ETC-S 1.069,2.859 1.656,3.006 0.586,0.147 10 FL MAIN 1.2,4.447 1.682,4.623 0.482,0.176 10 Battery 3.514,3.154 4.135,3.307 0.621,0.154 10 Shielded 5.336,1.872 6.380,2.228 1.045,0.356 10 Throttle Actuator Control Circuit 5.597,5.11 6.045,5.280 0.448,0.170 10 ECM 4.574,4.256 4.795,4.426 0.221,0.170 10 20 2.038,3.17 2.315,3.340 0.276,0.170 10 D41

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (+BM VOLTAGE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / +BM Voltage.


e.

Read the value displayed on the tester.

Result
Result Proceed to
Less than 4 V A
11 to 14 V B



A

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY, BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY, BODY GROUND)
a.

Disconnect the ECM connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-3 (+BM) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D1-20 (ME01) - Body ground Always Below 1 Ω
D1-81 (E1) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR