Refer to DTC P0617 (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0617).
Refer to DTC P0617 (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0617).
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester ON.
Enter the following menus: Powertrain / Engine / Data List / Starter Signal.
Check the result when the engine switch is turned on (IG).
Check the result when the engine starts.
| Engine Switch Condition | Tester Display (Starter Signal) |
|---|---|
| On (IG) | OFF |
| Engine starts | ON |
NG
OK
Disconnect the ECM connector.
Check that the shift lever is in the P position.
Measure the voltage between the ECM terminal and body ground when operating the engine switch to start cranking.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A7-14 (STSW) - Body ground | Always | 11 to 14 V |
OK
NG
Disconnect the Park/Neutral Position (PNP) switch connector.
Measure the voltage between the terminal of the PNP switch connector and body ground while cranking the engine.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D4-4 (B) - Body ground | Engine switch on (IG) | 11 to 14 V |
OK
NG
Inspect the PNP switch assembly (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).
NG
(See pageDrivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL)
OK
Disconnect the main body ECU connector.
Disconnect the ECM connector.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G60-4 (STSW) - A7-14 (STSW) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G60-4 (STSW) - Body ground | Always | Below 1 Ω |
OK
NG
Remove the ST CUT relay from the fusible link block.
Measure the resistance.
| Tester Connection | Specified Condition |
|---|---|
| 3 - 5 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω
(When battery voltage applied to terminals 1 and 2) |
OK
NG
Remove the ST CUT relay from the fusible link block.
Turn the engine switch on (IG).
Measure the voltage between the terminals of the ST CUT relay holder.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST CUT relay holder terminal (1) - ST CUT relay holder terminal (2) | Engine switch on (IG) | 11 to 14 V |
Reinstall the relay.
OK
NG
Remove the ST CUT relay from the fusible link block.
Disconnect the PNP switch assembly connector.
Disconnect the main body ECU connector.
Disconnect the ECM connector.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST CUT relay holder terminal (3) - D1-63 (STAR) | Always | Below 1 Ω |
| ST CUT relay holder terminal (3) - G60-6 (STR2) | Always | Below 1 Ω |
| G57-8 (STR) - ST CUT relay holder terminal (5) | Always | Below 1 Ω |
| D4-4 (B) - ST CUT relay holder terminal (5) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST CUT relay holder terminal (3) - Body ground | Always | 10 kΩ or higher |
| ST CUT relay holder terminal (5) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the ECM connector.
Remove the ST CUT relay from the fusible link block.
Measure the resistance between the terminals of the ST CUT relay holder.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST CUT relay holder terminal (3) - Body ground | Always | 10 kΩ or higher |
| ST CUT relay holder terminal (5) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the ST relay from the engine room No. 1 relay block.
Disconnect the PNP switch assembly connector.
Disconnect the ECM connector.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D4-9 (L) - STA (A7-48) | Always | Below 1 Ω |
| D4-9 (L) - ST relay holder terminal (1) | Always | Below 1 Ω |
| ST relay holder terminal (2) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D4-9 (L) - Body ground | Always | 10 kΩ or higher |
OK
NG
Check that the battery is not depleted.
Battery is not depleted.
OK
NG
Check that the battery terminals are not loose or corroded.
Battery terminals are not loose or corroded.
OK
NG