Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0660  Intake Manifold Tuning Valve Control Circuit / Open (Bank 1)  


DESCRIPTION

This circuit opens and closes the intake air control valve assembly (built into intake air surge tank assembly) in response to changes in the engine load in order to increase the intake efficiency using the acoustic control induction system.

When the engine speed is between 0 and 4450 rpm and the throttle valve opening angle is 60° or more, the ECM supplies current to the actuator (on status), to close the intake air control valve assembly. Under other conditions, the intake air control valve assembly is open.

G102539E01
1.292,1.969 0.979,0.615 0.979,0.615 1.146,0.615 false 3.271,1.698 3.51,1.177 3.51,1.177 3.656,1.177 false 4.708,2.021 4.708,1.51 4.708,1.51 4.865,1.51 false 5.854,4.573 5.854,3.719 false 1.26,4.74 0.948,3.385 0.948,3.385 1.115,3.385 false 1.146,2.292 1.271,2.292 1.271,2.292 1.51,2.135 false 1.177,5.052 1.281,5.052 1.281,5.052 1.563,4.833 false 3.281,4.479 3.469,4.156 3.469,4.156 3.594,4.156 false 1.604,0.229 3.542,0.479 1.938,0.25 10 false Throttle Valve Opening Angle 0.135,0.104 1.229,0.427 1.094,0.323 10 false Engine Speed 1.448,1.135 1.885,1.427 0.438,0.292 10 false 1 1.969,1.135 2.406,1.427 0.438,0.292 10 false 3 2.469,1.135 2.906,1.427 0.438,0.292 10 false 5 1.458,2.802 1.896,3.094 0.438,0.292 10 false 2 1.958,2.823 2.396,3.115 0.438,0.292 10 false 4 2.49,2.833 2.927,3.125 0.438,0.292 10 false 6 4.281,2.792 4.719,3.083 0.438,0.292 10 false 60° 4.563,3.854 5,4.146 0.438,0.292 10 false 0 rpm 6.021,3.854 6.719,4.125 0.698,0.271 10 false 4450 rpm 4.917,1.448 7.042,1.927 2.125,0.479 10 false Intake Air Control Valve Assembly Closed (Actuator: on) 3.729,1.094 4.74,1.552 1.01,0.458 10 false Throttle Position Sensor 1.292,0.531 2.927,0.969 1.635,0.438 10 false Acoustic Control Induction System Actuator 0.417,0.719 0.885,1 0.469,0.281 10 false ECM 0.073,2.813 1.167,3.135 1.094,0.323 10 false Engine Speed 6.198,4.167 7.156,4.458 0.958,0.292 10 false Engine Speed 1.219,3.021 3.156,3.271 1.938,0.25 10 false Throttle Valve Opening Angle 1.208,3.281 2.844,3.719 1.635,0.438 10 false Acoustic Control Induction System Actuator 0.427,3.469 0.896,3.75 0.469,0.281 10 false ECM 0.042,2.219 1.146,2.615 1.104,0.396 10 false Intake Air Control Valve Assembly 0.073,4.979 1.177,5.375 1.104,0.396 10 false Intake Air Control Valve Assembly 2.469,3.906 2.906,4.198 0.438,0.292 10 false 5 1.979,3.896 2.417,4.188 0.438,0.292 10 false 3 1.458,3.906 1.896,4.198 0.438,0.292 10 false 1 1.458,5.583 1.719,5.781 0.26,0.198 10 false 2 1.979,5.594 2.271,5.823 0.292,0.229 10 false 4 2.49,5.583 2.719,5.781 0.229,0.198 10 false 6 3.646,4.073 4.656,4.531 1.01,0.458 10 false Throttle Position Sensor 4.583,4.615 6.667,5.042 2.083,0.427 10 false Intake Air Control Valve Assembly Open (Actuator: off) 3.229,2.5 4.135,2.979 0.906,0.479 10 false Throttle Valve Opening Angle

DTC No. DTC Detection Condition Trouble Area
P0660 The following conditions are met simultaneously for 0.5 seconds or more (2 trip detection logic):
1.

Voltage of terminal acoustic control induction system of the ECM is low when the actuator is off

2.

The engine has been started


·

Open or short in intake air control valve assembly circuit

·

Intake air surge tank assembly (intake air control valve assembly)

·

ECM



WIRING DIAGRAM

A159623E02
6.299,0.139 6.646,0.298 0.347,0.159 10 ECM 4.357,0.017 4.642,0.177 0.284,0.159 10 D48 4.357,0.186 5.298,0.345 0.941,0.159 10 ACIS Actuator 3.195,0.124 3.834,0.283 0.639,0.159 10 EFI MAIN 0.583,1.02 0.850,1.180 0.267,0.159 10 EFI 0.583,1.577 1.228,1.737 0.645,0.159 10 F/B BATT 0.583,2.128 1.179,2.288 0.597,0.159 10 FL MAIN 0.69,2.801 1.171,2.960 0.481,0.159 10 Battery 6.089,0.548 6.435,0.708 0.347,0.159 10 ACIS 5.748,0.548 5.945,0.708 0.198,0.159 10 D1 5.72,0.335 5.973,0.494 0.253,0.159 10 107 6.089,1.284 6.498,1.443 0.409,0.159 10 MREL 5.748,1.284 5.945,1.443 0.198,0.159 10 A7 5.753,1.07 5.940,1.230 0.187,0.159 10 44 5.07,0.65 5.172,0.809 0.102,0.159 10 1 3.903,1.191 4.005,1.351 0.102,0.159 10 1 4.443,0.65 4.545,0.809 0.102,0.159 10 2 3.042,1.191 3.144,1.351 0.102,0.159 10 2 3.903,0.452 4.005,0.611 0.102,0.159 10 3 3.042,0.452 3.144,0.611 0.102,0.159 10 5

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE FOR INTAKE CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Active the VSV for Intake Control.


d.

Check if operating noise can be heard when operating the intake air control valve assembly using the tester.

OK:

Operating noise can be heard.




OK

NG

2.INSPECT INTAKE AIR CONTROL VALVE ASSEMBLY OPERATION
2.INSPECT INTAKE AIR CONTROL VALVE ASSEMBLY OPERATION
a.

Inspect the intake air control valve assembly (See page Engine / Hybrid System>2GR-FE INTAKE>INTAKE AIR CONTROL VALVE>ON-VEHICLE INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR

NG

REPLACE INTAKE AIR CONTROL VALVE ASSEMBLY (INTAKE AIR SURGE TANK ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR
a.

Check the wire harness and connectors between the ACIS actuator and ECM.

i.

Disconnect the ACIS actuator connector.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance between the terminals of the ACIS connector and ECM connector.

Standard resistance (Check for open):
Tester Connection Condition Specified Condition
D48-1 - D1-107 (ACIS) Always Below 1 Ω


Standard resistance (Check for short):
Tester Connection Condition Specified Condition
D48-1 or D1-107 (ACIS) - Body ground Always 10 kΩ or higher




b.

Check the wire harness between the ACIS connector and EFI MAIN relay.

i.

Remove the EFI MAIN relay from the engine room No. 1 relay block.


ii.

Measure the resistance between the terminals.

Standard resistance (Check for open):
Tester Connection Condition Specified Condition
D48-2 - EFI MAIN relay holder (3) Always Below 1 Ω





OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR