EURO-OBD (EUROPEAN SPEC.)
When troubleshooting Europe On-Board Diagnostic (Euro-OBD) vehicles, the vehicle must be connected to an OBD scan tool (complying with ISO 15765-4). Various data output from the vehicle's ECM can then be read.
Euro-OBD regulations require that the vehicle's on-board computer illuminates the Malfunction Indicator Lamp (MIL) on the instrument panel when the computer detects a malfunction in:
The emission control system/components.
The powertrain control components (which affect vehicle emissions).
The computer.
In addition, the applicable Diagnostic Trouble Codes (DTCs) prescribed by ISO 15765-4 are recorded in the ECM memory. If the malfunction does not recur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the ECM memory.
To check DTCs, connect the intelligent tester or an OBD scan tool to the Data Link Connector 3 (DLC3) of the vehicle.
The scan tool displays DTCs, the freeze frame data and a variety of the engine data.
The DTCs and freeze frame data can be erased using the scan tool (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
M-OBD (EXCEPT EUROPEAN SPEC.)
When troubleshooting Multiplex On-Board Diagnostic (M-OBD) vehicles, the vehicle must be connected to the intelligent tester. Various data output from the ECM can then be read.
OBD regulations require that the vehicle's on-board computer illuminates the MIL on the instrument panel when the computer detects a malfunction in:
The emission control system/components.
The powertrain control components (which affect vehicle emissions).
The computer.
In addition, the applicable DTCs are recorded in the ECM memory. If the malfunction does not recur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the ECM memory.
J-OBD2
When troubleshooting J-OBD2 vehicles, the vehicle must be connected to the intelligent tester. Various data output from the ECM can then be read.
OBD regulations require that the vehicle's on-board computer illuminates the MIL on the instrument panel when the computer detects a malfunction in:
The emission control system/components.
The powertrain control components (which affect vehicle emissions).
The computer.
In addition, the applicable DTCs are recorded in the ECM memory. If the malfunction does not recur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the ECM memory.
NORMAL MODE AND CHECK MODE
The diagnosis system operates in normal mode during normal vehicle use. In normal mode, 2 trip detection logic is used to ensure accurate detection of malfunctions. Check mode is also available as an option for technicians. In check mode, 1 trip detection logic is used for duplicating malfunction symptoms and increasing the system's ability to detect malfunctions, including intermittent problems (intelligent tester only).
2 TRIP DETECTION LOGIC
When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected during the next subsequent drive cycle, the MIL is illuminated (2nd trip).
DLC3 (Data Link Connector 3)
Check the DLC3 (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>GENERAL INFORMATION).
INSPECT BATTERY VOLTAGE
11 to 14 V
If voltage is below 11 V, replace or recharge the battery.
CHECK MIL
Check that the MIL illuminates when turning the engine switch is turned on (IG).
If the MIL does not illuminate, there is a problem in the MIL circuit (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>MIL Circuit).
When the engine is started, the MIL should turn off.
ALL READINESS
With "All Readiness" you can check whether or not the DTC judgment has been completed by using the intelligent tester.
You should check "All Readiness" after simulating malfunction symptoms or for validation after finishing repairs.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and wait for at 30 seconds.
Turn the engine switch on (IG) and turn the tester on.
Perform the DTC judgment driving pattern to run the DTC judgment.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTCs to be confirmed.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform the driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |