Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM J

2GR-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM. When the engine switch is turned on (IG), power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually: When the engine switch is turned on (IG), the MIL should be illuminated and should then turn off after engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the intelligent tester.

WIRING DIAGRAM

A159635E04
5.438,2.354 5.677,2.531 0.24,0.177 10 false A7 5.448,2.125 5.74,2.302 0.292,0.177 10 false 24 5.031,2.219 5.323,2.396 0.292,0.177 10 false 25 3.906,2.479 4.198,2.656 0.292,0.177 10 false IG2 1.958,3.042 2.25,3.219 0.292,0.177 10 false IG2 0.688,2.802 0.979,2.979 0.292,0.177 10 false IG2 0.313,1.813 1,1.99 0.688,0.177 10 false AM2 No. 2 0.698,3.646 1.344,3.823 0.646,0.177 10 false F/B BATT 0.698,4.167 1.292,4.344 0.594,0.177 10 false FL MAIN 0.833,4.854 1.302,5.031 0.469,0.177 10 false Battery 3.188,2.479 3.604,2.656 0.417,0.177 10 false MET 1.292,1.573 2.521,1.75 1.229,0.177 10 false Main Body ECU 3.635,2.771 5.146,2.948 1.51,0.177 10 false G28 Combination Meter 4.344,2.49 4.635,2.667 0.292,0.177 10 false MIL 4.74,2.438 5.031,2.615 0.292,0.177 10 false EFI 6.135,5.302 6.656,5.479 0.521,0.177 10 false ECM 3.625,2.219 3.917,2.396 0.292,0.177 10 false 21 2.406,2.219 2.698,2.396 0.292,0.177 10 false 3 1.667,2.219 1.958,2.396 0.292,0.177 10 false 5 1.667,2.625 1.958,2.802 0.292,0.177 10 false 2 2.406,2.625 2.698,2.802 0.292,0.177 10 false 1 5.76,2.219 6.198,2.396 0.438,0.177 10 false W 0.938,0.813 1.281,0.99 0.344,0.177 10 false G57 1.031,0.583 1.323,0.76 0.292,0.177 10 false 6 2.354,0.802 2.698,0.979 0.344,0.177 10 false G58 2.417,0.583 2.708,0.76 0.292,0.177 10 false 11 0.938,1.281 1.281,1.458 0.344,0.177 10 false G58 1.302,0.771 1.719,0.948 0.417,0.177 10 false AM1 1.938,0.771 2.354,0.948 0.417,0.177 10 false IG2D 1.302,1.24 1.719,1.417 0.417,0.177 10 false AM2 1.031,1.063 1.323,1.24 0.292,0.177 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result:
Condition Proceed to
MIL remains ON A
MIL does not illuminate B




A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER MIL TURNS OFF
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / DTC.


d.

Check if any DTCs have been stored. Note down any DTCs.



f.

Check if the MIL goes off.

Standard:

MIL should go off.




NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

OK

REPAIR CIRCUIT INDICATED BY OUTPUT DTC

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.
U188288E01
1.786,1.77 2.706,1.926 false 0.053,0.035 1.342,0.198 1.289,0.163 10 Wire Harness Side: 1.109,0.762 2.158,0.931 1.049,0.169 10 ECM Connector 1.282,2.569 1.993,2.708 0.711,0.139 10 Front View 0.64,0.763 0.831,0.944 0.191,0.181 10 A7 2.753,1.839 2.909,2.020 0.156,0.181 10 W

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.




NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A7-24 (W) or G28-25 (EFI) - Body ground Always 10 kΩ or higher




NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

REPAIR OR REPLACE COMBINATION METER ASSEMBLY

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the engine switch is turned on (IG).

OK:

MIL should be illuminated.




NG

6.CHECK THAT ENGINE STARTS

OK

6.CHECK THAT ENGINE STARTS
a.

Start the engine.

Result:
Result Proceed to
Engine starts A
Engine does not start* B


HINT:

*: The intelligent tester cannot communicate with the ECM.




A

7.INSPECT COMBINATION METER ASSEMBLY (MIL CIRCUIT)

B

7.INSPECT COMBINATION METER ASSEMBLY (MIL CIRCUIT)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

NG

REPAIR OR REPLACE COMBINATION METER ASSEMBLY