Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM U

2GR-FE ENGINE CONTROL  SFI SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under Normal Condition are reference only. Do not depend solely on these values when determining whether or not a part is faulty.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine / Data List.


g.

According to the display on the tester, read the Data List.



Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed:
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
Actual vehicle speed Speed indicated on speedometer
Engine Speed Engine speed:
Min.: 0 rpm, Max.: 16383 rpm
600 to 700 rpm : Idling -
Calculate Load Calculated load by ECM:
Min.: 0%, Max.: 100%
·

10 to 20%: Idling

·

10 to 20%: Running without load (2500 rpm)


-
Vehicle Load Vehicle load:
Min.: 0%, Max.: 25700%
Actual vehicle load -
MAF Air flow rate from mass air flow meter:
Min.: 0 gm/sec, Max.: 655.35 gm/sec
·

2 to 5 gm/sec: Idling

·

8 to 19 gm/sec: 2500 rpm


If value is approximately 0.0 gm/sec:
·

Mass air flow meter power source circuit open


·

VG circuit open or short


If value is 271.0 gm/sec or more:
·

E2G circuit open


Atmosphere Pressure Atmospheric pressure:
Min.: 0 kPa (0 mmHg, 0 in.Hg), Max.: 255 kPa (1913 mmHg, 75 in.Hg)
Equivalent to atmospheric pressure (absolute pressure) -
Coolant Temp Engine coolant temperature:
Min.: -40°C (-40°F), Max.: 140°C (284°F)
75 to 100°C
(167 to 212°F): After warming up
·

If value is -40°C (-40°F): sensor circuit open


·

If value is 140°C (284°F): sensor circuit shorted


Intake Air Intake air temperature:
Min.: -40°C (-40°F), Max.: 140°C (284°F)
Equivalent to ambient air temperature
·

If value is -40°C (-40°F): sensor circuit open


·

If value is 140°C (284°F): sensor circuit shorted


Engine Run Time Engine run time:
Min.: 0 s,
Max.: 65535 s
Time after engine started -
Initial Engine Coolant Temp Initial engine coolant temperature:
Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F)
Close to ambient air temperature -
Initial Intake Air Temp Initial intake air temperature:
Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F)
Close to ambient air temperature -
Battery Voltage Battery voltage:
Min.: 0, Max.: 65.535 V
11 to 14 V: Engine switch on (IG) -
Accel Sens. No. 1 Volt % Absolute accelerator pedal position No. 1:
Min.: 0%, Max.: 100%
10 to 22%: Accelerator pedal fully released
52 to 90%: Accelerator pedal fully depressed
-
Accel Sens. No. 2 Volt % Absolute accelerator pedal position No. 2:
Min.: 0%, Max.: 100%
24 to 40%: Accelerator pedal fully released
68 to 95%: Accelerator pedal fully depressed
-
Accel Sensor Out No. 1 APP sensor No. 1 voltage:
Min.: 0 V, Max.: 4.98 V
0.5 to 1.1 V: Accelerator pedal fully released
2.6 to 4.5 V: Accelerator pedal fully depressed.
-
Accel Sensor Out No. 2 APP sensor No. 2 voltage:
Min.: 0 V, Max.: 4.98 V
1.2 to 2.0 V: Accelerator pedal fully released
3.4 to 4.75 V: Accelerator pedal fully depressed.
-
Accelerator Idle Position Whether accelerator pedal position sensor detecting idle:
ON or OFF
ON: Idling -
Accel Fully Close #1 (AD) Accelerator fully closed value No. 1 (AD):
Min.: 0 V, Max.: 4.9 V
- -
Accel Fully Close Learn #1 Accelerator fully closed learning value No. 1:
Min.: 0 deg, Max.: 124.5 deg
- -
Accel Fully Close Learn #2 Accelerator fully closed learning value No. 2:
Min.: 0 deg, Max.: 124.5 deg
- -
Throttle Sensor Volt % Throttle valve opening percentage according to throttle position sensor:
Min.: 0%, Max.: 100%
·

10 to 22%: Accelerator pedal fully released

·

64 to 96%: Accelerator pedal fully depressed


Value calculated based on the voltage at terminal VTA1
Throttl Sensor #2 Volt % Throttle valve opening percentage according to throttle position sensor No. 2:
Min.: 0%, Max.: 100%
·

42 to 62%: Accelerator pedal fully released

·

92 to 100%: Accelerator pedal fully depressed


Value calculated based on the voltage at terminal VTA2
ST1 Brake pedal signal:
ON or OFF
ON: Brake pedal depressed -
System Guard System guard:
ON or OFF
- -
Open Side Malfunction Open side malfunction:
ON or OFF
- -
Throttle Idle Position Whether or not throttle position sensor detecting idling:
ON or OFF
·

ON: Accelerator pedal fully released

·

OFF: Accelerator pedal fully depressed


-
Throttle Require Position Required throttle position:
Min.: 0 V, Max.: 4.98 V
0.5 to 1.1 V: Idling -
Throttle Sensor Position (*1) Throttle position sensor:
Min.: 0%, Max.: 100%
·

0%: Accelerator pedal fully released

·

50 to 80%: Accelerator pedal fully depressed


Recognition value for throttle opening angle on ECM
Throttle Position No. 1 Throttle position sensor No. 1 output voltage:
Min.: 0 V, Max.: 4.98 V
·

0.5 to 1.1 V: Accelerator pedal fully released

·

3.2 to 4.8 V: Accelerator pedal fully depressed

·

0.6 to 1.4 V: Fail-safe operating


-
Throttle Position No. 2 Throttle position sensor No. 2 output voltage:
Min.: 0 V, Max.: 4.98 V
·

2.1 to 3.1 V: Accelerator pedal fully released

·

4.6 to 4.98 V: Accelerator pedal fully depressed

·

2.1 to 3.1 V: Fail-safe operating


-
Throttle Position Command Throttle position command value:
Min.: 0 V, Max.: 4.98 V
- -
Throttle Sens Open Pos #1 Throttle sensor opener position No. 1:
Min.: 0 V, Max.: 4.98 V
0.6 to 1.4 V -
Throttle Sens Open Pos #2 Throttle sensor opener position No. 2:
Min.: 0 V, Max.: 4.98 V
1.7 to 2.5 V -
Throttle Sens Open #1 (AD) Throttle position sensor No. 1 output voltage (AD):
Min.: 0 V, Max.: 4.9 V
- -
Throttle Motor Whether throttle actuator control permitted:
ON or OFF
ON: Engine switch to on (IG)
OFF: Electronic throttle control system has failed
-
Throttle Motor Current Throttle actuator current:
Min.: 0 A, Max.: 19.9 A
0 to 3.0 A: Idling -
Throttle Motor DUTY Throttle actuator:
Min.: 0%, Max.: 100%
10 to 22%: Idling after engine warmed up -
Throttle Motor Duty (Open) Throttle actuator duty ratio (open):
Min.: 0%, Max.: 100%
0 to 40% Idling -
Throttle Motor Duty (Close) Throttle actuator duty ratio (closed):
Min.: 0%, Max.: 100%
0 to 40% Idling -
Throttle Fully Close Learn Throttle valve fully closed (learned value):
Min.: 0 V, Max.: 4.98 V
0.4 to 1.0 V: Accelerator pedal fully released -
ETCS Actuator Power Electronic throttle control system power supply:
ON or OFF
ON: Engine switch on (IG) and system normal
OFF: Electronic throttle control system has failed
-
+BM Voltage +BM voltage:
Min.: 0 V, Max.: 79.99 V
11 to 14 V: Engine switch on (IG) and system normal -
Actuator Power Supply Throttle actuator power supply:
ON or OFF
ON: Idling -
Clutch Current Clutch current:
Min.: 0 A, Max.: 2.49 A
Unused -
Fail Safe Drive Whether or not fail-safe function executed
ON or OFF
ON: Electronic throttle control system has failed
OFF: Electronic throttle control system normal
-
Fail Safe Drive (Main CPU) Whether or not fail-safe function executed
ON or OFF
ON: Electronic throttle control system has failed
OFF: Electronic throttle control system normal
-
Throttle Position Throttle valve opening angle:
Min.: 0 deg, Max.: 499.99 deg
- When the engine stalls, is difficult to start, or idles roughly
ISC Flow Flow rate calculated from information from each sensor:
Min.: 0 L/s, Max.: 79.99 L/s
- When the engine stalls, is difficult to start, or idles roughly
ISC Position Target valve opening angle calculated from ISC control:
Min.: 0 deg, Max.: 499.99 deg
- When the engine stalls, is difficult to start, or idles roughly
ISC Feedback Value ISC feedback value:
Min.: -40 L/s, Max.: 39.99 L/s
- When the engine stalls, is difficult to start, or idles roughly
ISC Learning Value ISC learning value:
Min.: -40 L/s, Max.: 39.99 L/s
- When the engine stalls, is difficult to start, or idles roughly
Electric Load Feedback Val Electrical load feedback value:
Min.: -40 L/s, Max.: 39.99 L/s
- When the engine stalls, is difficult to start, or idles roughly
Air Conditioner FB Val Air conditioner load feedback value:
Min.: -40 L/s, Max.: 39.99 L/s
- When the engine stalls, is difficult to start, or idles roughly
PS Feedback Val Power steering load feedback value:
Min.: -40 L/s, Max.: 39.99 L/s
- When the engine stalls, is difficult to start, or idles roughly
Low Revolution Control Status of low engine speed control:
ON or OFF
- When the engine stalls, is difficult to start, or idles roughly
Neutral Control Neutral position control status for automatic transaxle:
ON or OFF
- When the engine stalls, is difficult to start, or idles roughly
N Range Status Judgment for shift lever neutral position:
ON or OFF
- When the engine stalls, is difficult to start, or idles roughly
Injector (Port) Injection duration of No. 1 cylinder:
Min.: 0 μs, Max.: 65535 μs
1200 to 2400 μs: Idling -
Injection Volume (Cylinder 1) Injection volume (Cylinder 1):
Min.: 0 ml, Max.: 2.047 ml
0.05 to 0.15 ml: Idling Total of fuel injection volume of 10 injections
Fuel Pump Speed Control FUEL PMP relay status:
ON or OFF
- -
Fuel Pump / Speed Status Fuel pump/status:
ON or OFF
ON: Engine running -
EVAP (Purge) VSV Purge VSV control duty:
Min.: 0%, Max.: 100%
0 to 100%: Idling Command signal from ECM
Evap Purge Flow Purge flow:
Min.: 0%, Max.: 399.9%
0 to 8%: Idling -
Purge Density Learn Value Learning value of purge density:
Min.: -50, Max.: 349.99
Idling: -40 to 0 -
EVAP Purge VSV Status of purge VSV control:
ON or OFF
- -
Target Air-Fuel Ratio Air-Fuel ratio:
Min.: 0, Max.: 1.998
0.8 to 1.2: Idling
·

0 to 0.999 = Rich

·

1 = Stoichiometric air fuel ratio

·

1.001 to 1.998 = Lean


AF Lambda B1S1 Short-term fuel trim associated with bank 1 sensor 1:
Min.: 0, Max.: 1.99
·

Value less than 1 (0.000 to 0.999) = Rich


·

Stoichiometric air-fuel ratio = 1


·

Value greater than 1 (1.001 to 1.99) = Lean


-
AF Lambda B2S1 Short-term fuel trim associated with bank 2 sensor 1:
Min.: 0, Max.: 1.99
·

Value less than 1 (0.000 to 0.999) = Rich


·

Stoichiometric air-fuel ratio = 1


·

Value greater than 1 (1.001 to 1.99) = Lean


-
AFS Voltage B1S1 Air fuel ratio sensor output voltage for bank 1 sensor 1:
Min.: 0 V, Max.: 7.99 V
2.8 to 3.8 V: Idling Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
AFS Voltage B2S1 Air fuel ratio sensor output voltage for bank 2 sensor 1:
Min.: 0 V, Max.: 7.99 V
2.8 to 3.8 V: Idling Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
AFS Current B1S1 Air fuel ratio sensor current:
Min.: -128 mA, Max.: 127.99 mA
- -
AFS Current B2S1 Air fuel ratio sensor current:
Min.: -128 mA, Max.: 127.99 mA
- -
O2S B1S2 Heated oxygen sensor output voltage for bank 1 sensor 2:
Min.: 0 V, Max.: 1.27 V
0.1 to 0.9 V:
Driving at 70 km/h (43 mph)
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
O2S B2S2 Heated oxygen sensor output voltage for bank 2 sensor 2:
Min.: 0 V, Max.: 1.27 V
0.1 to 0.9 V:
Driving at 70 km/h (43 mph)
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
O2S Impedance B1S2 Heated oxygen sensor impedance (bank 1 sensor 2):
Min.: 0 ohm, Max.: 21247.67 ohm
- -
O2S Impedance B2S2 Heated oxygen sensor impedance (bank 2 sensor 2):
Min.: 0 ohm, Max.: 21247.67 ohm
- -
Short FT #1 Short-term fuel trim of bank 1:
Min.: -100%, Max.: 99.2%
-15 to 15% Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
Long FT #1 Long-term fuel trim of bank 1:
Min.: -100%, Max.: 99.2%
-15 to 15% Overall fuel compensation carried out long-term to compensate for a continual deviation of short-term fuel trim from central value
Total FT #1 Total fuel trim of bank 1
Average value for fuel trim system of bank 1:
Min.: -0.5, Max.: 0.496
-0.28 to 0.2: Idling -
Short FT #2 Short-term fuel trim of bank 2:
Min.: -100%, Max.: 99.2%
-15 to 15% Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
Long FT #2 Long-term fuel trim of bank 2:
Min.: -100%, Max.: 99.2%
-15 to 15% Overall fuel compensation carried out long-term to compensate for a continual deviation of short-term fuel trim from central value
Total FT #2 Total fuel trim of bank 2
Average value for fuel trim system of bank 2:
Min.: -0.5, Max.: 0.496
-0.28 to 0.2: Idling -
Fuel System Status #1 OL, CL, OLDrive, OLFault or CLFault CL: Idling after warming up
·

OL (Open Loop): Has not yet satisfied conditions to go closed loop


·

CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control


·

OLDrive: Open loop due to driving conditions (fuel enrichment)


·

OLFault: Open loop due to detected system fault


·

CLFault: Closed loop but air fuel ratio sensor, which used for fuel control malfunctioning


Fuel System Status #2 OL, CL, OLDrive, OLFault or CLFault CL: Idling after warming up
·

OL (Open Loop): Has not yet satisfied conditions to go closed loop


·

CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control


·

OLDrive: Open loop due to driving conditions (fuel enrichment)


·

OLFault: Open loop due to detected system fault


·

CLFault: Closed loop but air fuel ratio sensor, which used for fuel control malfunctioning


IGN Advance Ignition timing advance for No. 1 cylinder:
Min.: -64 deg., Max.: 63.5 deg.
BTDC 7 to 24: Idling -
Knock Feedback Value Feedback value of knocking:
Min: -64°CA, Max.: 1023°CA
-22 to 0°CA:
Driving at 70 km/h (44 mph)
-
Knock Correct Learn Value Correction learning value of knocking:
Min: -64°CA, Max.: 1023°CA
0 to 22°CA:
Driving at 70 km/h (44 mph)
-
Idle Spark Advn Ctrl #1 Individual cylinder timing advance compensation amount (No. 1):
Min.: 0°CA, Max.: 15.93°CA
- When the engine stalls, is difficult to start, or idles roughly
Idle Spark Advn Ctrl #2 Individual cylinder timing advance compensation amount (No. 2):
Min.: 0°CA, Max.: 15.93°CA
- When the engine stalls, is difficult to start, or idles roughly
Idle Spark Advn Ctrl #3 Individual cylinder timing advance compensation amount (No. 3):
Min.: 0°CA, Max.: 15.93°CA
- When the engine stalls, is difficult to start, or idles roughly
Idle Spark Advn Ctrl #4 Individual cylinder timing advance compensation amount (No. 4):
Min.: 0°CA, Max.: 15.93°CA
- When the engine stalls, is difficult to start, or idles roughly
Idle Spark Advn Ctrl #5 Individual cylinder timing advance compensation amount (No. 5):
Min.: 0°CA, Max.: 15.93°CA
- When the engine stalls, is difficult to start, or idles roughly
Idle Spark Advn Ctrl #6 Individual cylinder timing advance compensation amount (No. 6):
Min.: 0°CA, Max.: 15.93°CA
- When the engine stalls, is difficult to start, or idles roughly
ACIS VSV Intake air control valve assembly for acoustic control induction system status:
ON or OFF
- -
VVT Control Status #1 VVT control (bank 1) status:
ON or OFF
- -
VVT Control Status #2 VVT control (bank 2) status:
ON or OFF
- -
VVT Advance Fail VVT control failure status:
ON or OFF
ON: VVT control failure -
VVT Aim Angle #1 (*2) VVT aim angle (Bank 1):
Min.: 0%, Max.: 399.9%
- VVT duty signal value during operation
VVT Change Angle #1 (*2) VVT change angle (Bank 1):
Min.: 0 degFR, Max.: 639.9 degFR
- Displacement angle during operation
VVT OCV Duty #1 (*2) VVT OCV (Bank 1) operation duty:
Min.: 0%, Max.: 399.9%
- Requested duty value for operation
VVT Aim Angle #2 (*2) VVT aim angle (Bank 2):
Min.: 0%, Max.: 399.9%
- VVT duty signal value during operation
VVT Change Angle #2 (*2) VVT change angle (Bank 2):
Min.: 0 degFR, Max.: 639.9 degFR
- Displacement angle during operation
VVT OCV Duty #2 (*2) VVT OCV (bank 2) operation duty:
Min.: 0%, Max.: 399.9%
- Requested duty value for operation
VVT Ex Hold Lrn Val #1 (*2) VVT exhaust hold duty ratio learning value (bank 1):
Min.: 0%, Max.: 399.9%
- -
VVT Ex Chg Angle #1 (*2) VVT exhaust change angle (bank 1):
Min.: 0 degFR, Max.: 639.9 degFR
- -
VVT Ex OCV Duty #1 (*2) VVT exhaust OCV duty (bank 1):
Min.: 0%, Max.: 399.9%
- -
VVT Ex Hold Lrn Val #2 (*2) VVT exhaust hold duty ratio learning value (bank 2):
Min.: 0%, Max.: 399.9%
- -
VVT Ex Chg Angle #2 (*2) VVT exhaust change angle (bank 2):
Min.: 0 degFR, Max.: 639.9 degFR
- -
VVT Ex OCV Duty #2 (*2) VVT exhaust OCV duty (bank 2):
Min.: 0%, Max.: 399.9%
- -
Catalyst Temp B1S1 Catalyst temperature (bank 1, sensor 1):
Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F)
- -
Catalyst Temp B2S1 Catalyst temperature (bank 2, sensor 1):
Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F)
- -
Catalyst Temp B1S2 Catalyst temperature (bank 1, sensor 2):
Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F)
- -
Catalyst Temp B2S2 Catalyst temperature (bank 2, sensor 2):
Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F)
- -
Starter Signal Starter signal:
ON or OFF
ON: Starter signal on -
Starter Control Starter signal status:
ON or OFF
- -
Power Steering Signal Power steering signal:
ON or OFF
ON: Power steering operation -
Starter Relay Starter relay:
ON or OFF
ON: Cranking -
Power Steer. Sig. Record Power steering signal (history):
ON or OFF
ON: When steering wheel first turned after battery terminals connected Signal status usually ON until battery terminals disconnected
ACC Relay ACC relay:
ON or OFF
ON: Cranking -
Neutral Position SW Signal Park/Neutral position switch assembly status:
ON or OFF
ON: Shift lever in P or N -
Stop Light Switch Stop light switch assembly:
ON or OFF
ON: Brake pedal depressed -
A/C Signal A/C signal:
ON or OFF
ON: A/C ON -
Closed Throttle Position SW Closed throttle position switch:
ON or OFF
·

ON: Throttle fully closed


·

OFF: Throttle open


-
Electrical Load Signal Electrical load signal:
ON or OFF
ON: Headlights or defogger turned on -
Check Mode Check mode:
ON or OFF
ON: Check mode on See page (Click here)
SPD Test Result Check mode result for vehicle speed sensor:
Compl or Incmpl
- -
Misfire Test Result Check mode result for misfire monitor:
Compl or Incmpl
- -
OXS1 Test Result Check mode result for heated oxygen sensor (bank 1):
Compl or Incmpl
- -
OXS2 Test Result Check mode result for heated oxygen sensor (bank 2):
Compl or Incmpl
- -
A/F Test Results #2 Check mode result for air fuel ratio sensor (Bank 2):
Compl or Incmpl
- -
A/F Test Results #1 Check mode result for air fuel ratio sensor (Bank 1):
Compl or Incmpl
- -
Complete Parts Monitor Comprehensive component monitor:
Not Avl or Avail
- -
Fuel System Monitor Fuel system monitor:
Not Avl or Avail
- -
Misfire Monitor Misfire monitor:
Not Avl or Avail
- -
O2S(A/FS) Monitor O2S (A/FS) monitor/
Not Avl or Avail
- -
O2S(A/FS) Monitor O2S (A/FS) Monitor:
Compl or Incmpl
- -
Catalyst Monitor Catalyst monitor:
Not Avl or Avail
- -
Catalyst Monitor Catalyst Monitor:
Compl or Incmpl
- -
# Codes (Include History) # Codes:
Min.: 0, Max.: 255
- Number of detected DTCs
MIL MIL status:
ON or OFF
ON: MIL on -
MIL ON Run Distance MIL ON run distance:
Min.: 0 km (0 mile),
Max.: 65535 km (40723 mile)
Distance after DTC detected -
Running Time from MIL ON Running time from MIL ON:
Min.: 0 min,
Max.: 65535 min
Equivalent to running time after MIL ON -
Time After DTC Cleared Time after DTC cleared:
Min.: 0 min,
Max.: 65535 min
Equivalent to time after DTCs cleared -
Distance from DTC Cleared Distance after DTC cleared:
Min.: 0 km(0 mile), Max.: 65535 km (40723 mile)
Equivalent to drive distance after DTCs cleared -
Warmup Cycle Cleared DTC Warm-up cycle after DTC cleared:
Min.: 0, Max.: 255
- Number of warm-up cycles after DTC cleared
OBD Requirements OBD Requirement E-OBD or JOBD -
Number of Emission DTC Number of emission related DTC - -
TC and TE1 TC and TE1 terminal of DLC 3:
ON or OFF
- -
Ignition Trig. Count Ignition counter:
Min.: 0, Max.: 65535
0 to 600 -
Cylinder #1 Misfire Count Misfire count of cylinder 1:
Min.: 0, Max.: 255
0 -
Cylinder #2 Misfire Count Misfire count of cylinder 2:
Min.: 0, Max.: 255
0 -
Cylinder #3 Misfire Count Misfire count of cylinder 3:
Min.: 0, Max.: 255
0 -
Cylinder #4 Misfire Count Misfire count of cylinder 4:
Min.: 0, Max.: 255
0 -
Cylinder #5 Misfire Count Misfire count of cylinder 5:
Min.: 0, Max.: 255
0 -
Cylinder #6 Misfire Count Misfire count of cylinder 6:
Min.: 0, Max.: 255
0 -
All Cylinders Misfire Count All cylinders misfire count:
Min.: 0, Max.: 255
0 -
Misfire RPM Engine speed when misfire occurs:
Min.: 0 rpm, Max.: 6375 rpm
0 rpm: Misfire 0 -
Misfire Load Engine load when misfire occurs:
Min.: 0 g/rev, Max.: 3.98 g/rev
- -
Misfire Margin Margin to detect engine misfire:
Min.: -100%, Max.: 127%
0 to 127% Misfire detection margin
Engine Starting Time Engine run time (elapsed time from engine switch on (IG) to off):
Min.: 0 ms, Max.: 655350 ms
- When the engine stalls, is difficult to start, or idles roughly
Engine Speed (Starter Off) Engine speed when starter off:
Min.: 0 rpm, Max.: 51199 rpm
- When the engine stalls, is difficult to start, or idles roughly
Starter Count Number of times starter turned on after engine switch turned from off to ON):
Min.: 0, Max.: 255
- When the engine stalls, is difficult to start, or idles roughly
Run Dist of Previous Trip Distance traveled during previous trip:
Min.: 0 km (0mile), Max.: 655.35 km (407 mile)
- When the engine stalls, is difficult to start, or idles roughly
Previous Trip Coolant Temp Coolant temperature of previous trip:
Min.: -40°C (-40°F), Max.: 215°C (419°F)
- When the engine stalls, is difficult to start, or idles roughly
Previous Trip Intake Temp Intake air Coolant temperature of previous trip:
Min.: -40°C (-40°F), Max.: 215°C (419°F)
- When the engine stalls, is difficult to start, or idles roughly
Engine Oil Temperature Engine oil temperature (estimated):
Min.: -40°C (-40°F), Max.: 215°C (419°F)
- When the engine stalls, is difficult to start, or idles roughly
Previous Trip Eng Oil Temp Engine oil temperature of previous trip (estimated):
Min.: -40°C (-40°F), Max.: 215°C (419°F)
- When the engine stalls, is difficult to start, or idles roughly
Ambient Temp for A/C Ambient temperature:
Min.: -40°C (-40°F), Max.: 215°C (419°F)
- When the engine stalls, is difficult to start, or idles roughly
Previous Trip Ambient Temp Ambient temperature of previous trip:
Min.: -40°C (-40°F), Max.: 215°C (419°F)
- When the engine stalls, is difficult to start, or idles roughly
Low Rev for Eng Start History of low engine speed after engine starts:
ON or OFF
- -
Minimum Engine Speed Minimum engine speed:
Min.: 0 rpm, Max.: 51199 rpm
- When the engine stalls, is difficult to start, or idles roughly
Battery Current Battery current:
Min.: -100 A, Max.: 100 A
- -
Battery Temperature Battery temperature:
Min.: -45°C (-49°F), Max.: 156.4°C (313.5°F)
- -
Alternator Output Duty Generator output duty:
Min.: 0%, Max.: 100%
- -
Alt Vol - Non Active Test Request voltage when regulator not under forced activation:
Min.: 0 V, Max.: 20 V
Battery electrolyte temperature varies (12.5 to 14.8 V) while driving: After engine start Alternator regulator output voltage is output
When performing Active Test, value is 0 V
Alt Vol - Active Test Request voltage when regulator under forced activation:
Min.: 0 V, Max.: 20 V
Request instruction voltage value: After engine start Charging control service data
When performing Active Test, value is 0 V
Electric Fan Motor Electric fan motor:
ON or OFF
- -
Idle Fuel Cut Fuel cut idle:
ON or OFF
ON: Fuel cut operation Idle fuel cut = "ON" when throttle valve fully closed and engine speed over 1400 rpm
FC TAU Fuel cut TAU (Fuel cut with a very light load):
ON or OFF
ON: Fuel cut operating Fuel cut being performed with a very light load to prevent incomplete engine combustion
Model Code Model code information GRS 50# -
Engine Type Engine type information 2GRFE -
Cylinder Number Cylinder number
Min.: 0, Max.: 255
6 -
Transmission Type Transmission type ECT 6th -
Destination Destination information W or @ -
Model Year Model year:
Min.: 1900, Max.: 2155
20## -
System Identification System identification Gasoline (gasoline engine) -
Engine Speed of Cyl #1 Engine Speed of Cylinder #1 of Injection Stopped:
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
Engine Speed of Cyl #2 Engine Speed of Cylinder #2 of Injection Stopped:
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
Engine Speed of Cyl #3 Engine Speed of Cylinder #3 of Injection Stopped:
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
Engine Speed of Cyl #4 Engine Speed of Cylinder #4 of Injection Stopped:
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
Engine Speed of Cyl #5 Engine Speed of Cylinder #5 of Injection Stopped:
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
Engine Speed of Cyl #6 Engine Speed of Cylinder #6 of Injection Stopped:
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
Av Engine Speed of All Cyl Average Engine Speed of All Cylinders of Injection Stopped:
Min.: 0 rpm, Max.: 51199 rpm
- Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
Received MIL from ECT Received MIL from TCM:
ON or OFF
MIL illuminate instruction on signal from TCM: ON -
Shift Position Sig from ECT Received shift position signal from TCM:
1st, 2nd, 3rd, 4th, 5th, or 6th
Actual shift position -
A/T Oil Temp from ECT ATF temperature:
Min.: -40°C (-40°F), Max.: 215°C (419°F)
- -
SPD (NO) Output shaft speed:
Min.: 0 rpm, Max.: 12750 rpm
- -
ECT Lock Up Lock up: ON or OFF - -
Shift SW Status (P Range) Park/neutral position switch assembly switch status:
ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


-
Shift SW Status (R Range) Park/neutral position switch assembly switch status:
ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


-
Shift SW Status (N Range) Park/neutral position switch assembly switch status:
ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


-
Sports Shift Up SW Sports shift up switch status:
ON or OFF
"+" pressed continuously: ON
"+" released: OFF
-
Sports Shift Down SW Sports shift down switch status:
ON or OFF
"-" pressed continuously: ON
"-" released: OFF
-
Sports Mode Selection SW Sports mode select switch status:
ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" and "-"


-
Shift SW Status (D Range) Park/neutral position switch assembly switch status:
ON or OFF
·

ON: Shift lever in D or S

·

OFF: Shift lever not in D or S


-

HINT:
·

*1: Excluding throttle valve opening percentage due to idle speed control.

·

*2: Data List values are only displayed when performing the following Active Test: Control the VVT System (Bank 1, 2), Control the VVT Linear (Bank 1, 2) and Control the VVT Exhaust Linear (Bank 1, 2). For other Active Test, the Data List value will be 0.

·

Normal condition: If no idling conditions are specified, the shift lever should be in the N or P, and the A/C switch and all accessory switches should be off.



ACTIVE TEST


HINT:

Performing an Active Test enables components including the relays, VSV (Vacuum Switching Valve) and actuators, to be operated without removing any parts. The Active Test can be performed with an intelligent tester. Performing an Active Test as the first step in troubleshooting is one method to shorten diagnostic time.


Data List can be displayed during Active Test.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Active Test.


e.

Perform the Active Test by referring to the table below.



Tester Display Test Part Control Range Diagnostic Note
Control the Injection Volume Change injection volume Between -12.5 and 24.8%
·

All injectors tested at same time


·

Perform test at less than 3000 rpm


·

Injection volume can be changed in fine graduations within control range


Control the Injection Volume for A/F Sensor Change injection volume 12.5%/0%/12.5%
·

Perform test at less than 3000 rpm


·

Control the Injection Volume for A/F Sensor enables to check and graph of air fuel ratio sensor and heated oxygen sensor voltage outputs


Activate the Fuel Pump Speed Control Fuel pump speed control ON (low speed)/OFF (high speed) Test possible when following conditions met:
·

Engine switch on (IG)


·

Engine is stopped


Activate the VSV for Intake Control ACIS VSV ON/OFF -
Activate the VSV for Evap Control Activate purge VSV ON/OFF -
Control the A/C Magnet Clutch A/C magnet clutch ON/OFF -
Control the Fuel Pump / Speed Activate fuel pump (C/OPN Relay) ON/OFF -
Connect the TC and TE1 Turn on and off TC and TE1 connection ON/OFF
·

ON: TC and TE1 connected


·

OFF: TC and TE1 disconnected


Control the Idle Fuel Cut Prohibit Prohibit idling fuel cut control ON/OFF -
Control the Electric Cooling Fan Control electric cooling fan ON/OFF Test possible when following conditions met:
·

Engine switch on (IG)


·

Engine is stopped


Activate the Starter Relay Starter ON/OFF -
Activate the ACC Cut Relay Activate ACC relay (ACC relay cut signal) ON/OFF Test is possible when following conditions are met:
·

Engine switch on (IG)

·

Engine is stopped


Control the ETCS Open Slow Speed Throttle actuator ON: Throttle valve opens slowly Test possible when following conditions met:
·

Engine switch on (IG)


·

Engine is stopped


·

Fully depressing accelerator pedal (APP: 58 degrees or more)


Control the ETCS Close Slow Speed Throttle actuator ON: Throttle valve closes slowly Same as above
Control the ETCS Open Fast Speed Throttle actuator ON: Throttle valve opens fast Same as above
Control the ETCS Close Fast Speed Throttle actuator ON: Throttle valve closes fast Same as above
Control the VVT Linear (Bank 1) Control VVT (bank 1) -128 to 127%
This valve added to present camshaft timing oil control valve assembly control duty
100%: Maximum advance
-100%: Maximum retard
Engine stall or rough idle when VVT actuator operated by 100%.
Test possible during idle.
Control the VVT System (Bank 1) Turn on and off camshaft timing oil control valve assembly ON/OFF
·

Engine stalls or idles roughly when camshaft timing oil control valve assembly turned on

·

Normal engine running or idling when camshaft timing oil control valve assembly off


Control the VVT Linear (Bank 2) Control VVT (bank 2) Between -128 and 127%
·

Engine stalls or idles roughly when VVT actuator operated by 100%

·

Test possible during idle


Control the VVT System (Bank 2) Turn on and off camshaft timing oil control valve assembly ON/OFF
·

Engine stalls or idles roughly when camshaft timing oil control valve assembly turned on

·

Normal engine running or idling when camshaft timing oil control valve assembly off


Control the VVT Exhaust Linear (Bank 1) Control VVT (bank 1) -128 to 127%
This valve added to present camshaft timing oil control valve assembly control duty
100%: Maximum advance
-100%: Maximum retard
·

Engine stalls or idles roughly when VVT actuator operated by 100%

·

Test possible during idle


Control the VVT Exhaust Linear (Bank 2) Control VVT (bank 2) Between -128 and 127%
·

Engine stalls or idles roughly when VVT actuator operated by 100%

·

Test possible during idle


Control the Voltage of Alternator Request output voltage of generator regulator during forced activation -12.5 to 14.8 V Test possible during vehicle stopping and engine idling.
Control the Cylinder #1 Fuel Cut Cylinder #1 injector fuel cut ON/OFF Test possible during vehicle stopping and engine idling.
Control the Cylinder #2 Fuel Cut Cylinder #2 injector fuel cut ON/OFF Same as above
Control the Cylinder #3 Fuel Cut Cylinder #3 injector fuel cut ON/OFF Same as above
Control the Cylinder #4 Fuel Cut Cylinder #4 injector fuel cut ON/OFF Same as above
Control the Cylinder #5 Fuel Cut Cylinder #5 injector fuel cut ON/OFF Same as above
Control the Cylinder #6 Fuel Cut Cylinder #6 injector fuel cut ON/OFF Same as above
Check the Cylinder Compression*1 Check the cylinder compression pressure ON/OFF Fuel injection and ignition is stopped in all cylinders

HINT:

*1:

In this Active Test, the fuel and ignition of all cylinders is cut. The engine must then be cranked for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.


1.

Warm up the engine.

2.

Turn the engine switch off.

3.

Connect the intelligent tester to the DLC3.

4.

Turn the engine switch on (IG).

5.

Turn the tester on.

6.

Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression.

HINT:

To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.


7.

Push the snapshot button to turn the snapshot function on.

HINT:

Using the snapshot function, data can be recorded during the Active Test.


8.

While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

HINT:

After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited and each cylinder engine speed measurement enters standby mode.


9.

Crank the engine for about 10 seconds.

HINT:

Continue to crank the engine until the values change from the default value (51199 rpm).


10.

Monitor the engine speed (Engine Speed of Cyl #1 to #6) displayed on the tester.

HINT:

At first, the tester displays extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.


NOTICE:
·

Do not crank the engine continuously for 20 seconds or more.

·

If it is necessary to crank the engine again after Check the Cylinder Compression has been changed to ON and the engine has been cranked once, press Exit to return to the Active Test menu screen. Then change Check the Cylinder Compression to ON and crank the engine.

·

Use a fully-charged battery.



11.

Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.

NOTICE:

If the Active Test is changed to OFF while the engine is being cranked, the engine will start.


12.

Push the snapshot button to turn the snapshot function off.

13.

Enter the following menus: Function / Snapshot Review / Engine / Snapshot File Manager, select the recorded data and display the data.

HINT:

If the data is not displayed as a graph, the change of the values cannot be observed.


14.

Check the change in engine speed values.

HINT:

As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.