| Vehicle Speed
|
Vehicle speed:
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
|
Actual vehicle speed
|
Speed indicated on speedometer
|
| Engine Speed
|
Engine speed:
Min.: 0 rpm, Max.: 16383 rpm
|
600 to 700 rpm : Idling
|
-
|
| Calculate Load
|
Calculated load by ECM:
Min.: 0%, Max.: 100%
|
·
10 to 20%: Running without load (2500 rpm)
|
-
|
| Vehicle Load
|
Vehicle load:
Min.: 0%, Max.: 25700%
|
Actual vehicle load
|
-
|
| MAF
|
Air flow rate from mass air flow meter:
Min.: 0 gm/sec, Max.: 655.35 gm/sec
|
|
If value is approximately 0.0 gm/sec:
·
Mass air flow meter power source circuit open
If value is 271.0 gm/sec or more:
|
| Atmosphere Pressure
|
Atmospheric pressure:
Min.: 0 kPa (0 mmHg, 0 in.Hg), Max.: 255 kPa (1913 mmHg, 75 in.Hg)
|
Equivalent to atmospheric pressure (absolute pressure)
|
-
|
| Coolant Temp
|
Engine coolant temperature:
Min.: -40°C (-40°F), Max.: 140°C (284°F)
|
75 to 100°C
(167 to 212°F): After warming up
|
·
If value is -40°C (-40°F): sensor circuit open
·
If value is 140°C (284°F): sensor circuit shorted
|
| Intake Air
|
Intake air temperature:
Min.: -40°C (-40°F), Max.: 140°C (284°F)
|
Equivalent to ambient air temperature
|
·
If value is -40°C (-40°F): sensor circuit open
·
If value is 140°C (284°F): sensor circuit shorted
|
| Ambient Temperature
|
Ambient temperature:
Min.: -40°C (-40°F), Max.: 215°C (419°F)
|
-
|
-
|
| Engine Run Time
|
Engine run time:
Min.: 0 s,
Max.: 65535 s
|
Time after engine started
|
-
|
| Initial Engine Coolant Temp
|
Initial engine coolant temperature:
Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F)
|
Close to ambient air temperature
|
-
|
| Initial Intake Air Temp
|
Initial intake air temperature:
Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F)
|
Close to ambient air temperature
|
-
|
| Battery Voltage
|
Battery voltage:
Min.: 0, Max.: 65.535 V
|
11 to 14 V: Engine switch on (IG)
|
-
|
| Accel Sens. No. 1 Volt %
|
Absolute accelerator pedal position No. 1:
Min.: 0%, Max.: 100%
|
10 to 22%: Accelerator pedal fully released
52 to 90%: Accelerator pedal fully depressed
|
-
|
| Accel Sens. No. 2 Volt %
|
Absolute accelerator pedal position No. 2:
Min.: 0%, Max.: 100%
|
24 to 40%: Accelerator pedal fully released
68 to 95%: Accelerator pedal fully depressed
|
-
|
| Accel Sensor Out No. 1
|
APP sensor No. 1 voltage:
Min.: 0 V, Max.: 4.98 V
|
0.5 to 1.1 V: Accelerator pedal fully released
2.6 to 4.5 V: Accelerator pedal fully depressed.
|
-
|
| Accel Sensor Out No. 2
|
APP sensor No. 2 voltage:
Min.: 0 V, Max.: 4.98 V
|
1.2 to 2.0 V: Accelerator pedal fully released
3.4 to 4.75 V: Accelerator pedal fully depressed.
|
-
|
| Accelerator Idle Position
|
Whether accelerator pedal position sensor detecting idle:
ON or OFF
|
ON: Idling
|
-
|
| Accel Fully Close #1 (AD)
|
Accelerator fully closed value No. 1 (AD):
Min.: 0 V, Max.: 4.9 V
|
-
|
-
|
| Accel Fully Close Learn #1
|
Accelerator fully closed learning value No. 1:
Min.: 0 deg, Max.: 124.5 deg
|
-
|
-
|
| Accel Fully Close Learn #2
|
Accelerator fully closed learning value No. 2:
Min.: 0 deg, Max.: 124.5 deg
|
-
|
-
|
| Throttle Sensor Volt %
|
Throttle valve opening percentage according to throttle position sensor:
Min.: 0%, Max.: 100%
|
·
10 to 22%: Accelerator pedal fully released
·
64 to 96%: Accelerator pedal fully depressed
|
Value calculated based on the voltage at terminal VTA1
|
| Throttl Sensor #2 Volt %
|
Throttle valve opening percentage according to throttle position sensor No. 2:
Min.: 0%, Max.: 100%
|
·
42 to 62%: Accelerator pedal fully released
·
92 to 100%: Accelerator pedal fully depressed
|
Value calculated based on the voltage at terminal VTA2
|
| ST1
|
Brake pedal signal:
ON or OFF
|
ON: Brake pedal depressed
|
-
|
| System Guard
|
System guard:
ON or OFF
|
-
|
-
|
| Open Side Malfunction
|
Open side malfunction:
ON or OFF
|
-
|
-
|
| Throttle Idle Position
|
Whether or not throttle position sensor detecting idling:
ON or OFF
|
·
ON: Accelerator pedal fully released
·
OFF: Accelerator pedal fully depressed
|
-
|
| Throttle Require Position
|
Required throttle position:
Min.: 0 V, Max.: 4.98 V
|
0.5 to 1.1 V: Idling
|
-
|
| Throttle Sensor Position (*1)
|
Throttle position sensor:
Min.: 0%, Max.: 100%
|
·
0%: Accelerator pedal fully released
·
50 to 80%: Accelerator pedal fully depressed
|
Recognition value for throttle opening angle on ECM
|
| Throttle Position No. 1
|
Throttle position sensor No. 1 output voltage:
Min.: 0 V, Max.: 4.98 V
|
·
0.5 to 1.1 V: Accelerator pedal fully released
·
3.2 to 4.8 V: Accelerator pedal fully depressed
·
0.6 to 1.4 V: Fail-safe operating
|
-
|
| Throttle Position No. 2
|
Throttle position sensor No. 2 output voltage:
Min.: 0 V, Max.: 4.98 V
|
·
2.1 to 3.1 V: Accelerator pedal fully released
·
4.6 to 4.98 V: Accelerator pedal fully depressed
·
2.1 to 3.1 V: Fail-safe operating
|
-
|
| Throttle Position Command
|
Throttle position command value:
Min.: 0 V, Max.: 4.98 V
|
-
|
-
|
| Throttle Sens Open Pos #1
|
Throttle sensor opener position No. 1:
Min.: 0 V, Max.: 4.98 V
|
0.6 to 1.4 V
|
-
|
| Throttle Sens Open Pos #2
|
Throttle sensor opener position No. 2:
Min.: 0 V, Max.: 4.98 V
|
1.7 to 2.5 V
|
-
|
| Throttle Sens Open #1 (AD)
|
Throttle position sensor No. 1 output voltage (AD):
Min.: 0 V, Max.: 4.9 V
|
-
|
-
|
| Throttle Motor
|
Whether throttle actuator control permitted:
ON or OFF
|
ON: Engine switch to on (IG)
OFF: Electronic throttle control system has failed
|
-
|
| Throttle Motor Current
|
Throttle actuator current:
Min.: 0 A, Max.: 19.9 A
|
0 to 3.0 A: Idling
|
-
|
| Throttle Motor DUTY
|
Throttle actuator:
Min.: 0%, Max.: 100%
|
10 to 22%: Idling after engine warmed up
|
-
|
| Throttle Motor Duty (Open)
|
Throttle actuator duty ratio (open):
Min.: 0%, Max.: 100%
|
0 to 40% Idling
|
-
|
| Throttle Motor Duty (Close)
|
Throttle actuator duty ratio (closed):
Min.: 0%, Max.: 100%
|
0 to 40% Idling
|
-
|
| Throttle Fully Close Learn
|
Throttle valve fully closed (learned value):
Min.: 0 V, Max.: 4.98 V
|
0.4 to 1.0 V: Accelerator pedal fully released
|
-
|
| ETCS Actuator Power
|
Electronic throttle control system power supply:
ON or OFF
|
ON: Engine switch on (IG) and system normal
OFF: Electronic throttle control system has failed
|
-
|
| +BM Voltage
|
+BM voltage:
Min.: 0 V, Max.: 79.99 V
|
11 to 14 V: Engine switch on (IG) and system normal
|
-
|
| Actuator Power Supply
|
Throttle actuator power supply:
ON or OFF
|
ON: Idling
|
-
|
| Fail Safe Drive
|
Whether or not fail-safe function executed
ON or OFF
|
ON: Electronic throttle control system has failed
OFF: Electronic throttle control system normal
|
-
|
| Fail Safe Drive (Main CPU)
|
Whether or not fail-safe function executed
ON or OFF
|
ON: Electronic throttle control system has failed
OFF: Electronic throttle control system normal
|
-
|
| Throttle Position
|
Throttle valve opening angle:
Min.: 0 deg, Max.: 499.99 deg
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| ISC Flow
|
Flow rate calculated from information from each sensor:
Min.: 0 L/s, Max.: 79.99 L/s
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| ISC Position
|
Target valve opening angle calculated from ISC control:
Min.: 0 deg, Max.: 499.99 deg
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| ISC Feedback Value
|
ISC feedback value:
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| ISC Learning Value
|
ISC learning value:
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Electric Load Feedback Val
|
Electrical load feedback value:
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Air Conditioner FB Val
|
Air conditioner load feedback value:
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Low Revolution Control
|
Status of low engine speed control:
ON or OFF
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| N Range Status
|
Judgment for shift lever neutral position:
ON or OFF
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Eng Stall Control FB Flow
|
Intake air compensation flow rate:
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
·
The intake air amount and ignition timing are adjusted when there is a large decrease in engine speed (for example, a decrease to 550 rpm or less) in order to prevent engine stall.
·
For use when engine stall, starting problems or rough idle is present.
|
| Deposit Loss Flow
|
Flow loss due to deposits:
Min.: -40 L/s, Max.: 39.99 L/s
|
-
|
·
This value indicates the amount of compensation for a decrease in flow passage area due to the buildup of deposits on the throttle valve.
·
Check this value for reference when the engine stalls, is difficult to start, or idles roughly.
·
When the ISC learned value is initialized, performing the following procedures in order to quickly relearn the Deposit Loss Flow value. After the Deposit Loss Flow has been relearned, gradual fine adjustments will continue automatically.
-
Start the engine cold and allow the engine to idle.
-
After the engine is warmed up (engine coolant temperature is above 80°C [176°F]), allow the engine to idle for an additional 5 minutes.
-
Turn the engine switch off and wait for 30 seconds.
-
Start the engine again, and allow the engine to idle for 5 minutes.
|
| Injector (Port)
|
Injection duration of No. 1 cylinder:
Min.: 0 μs, Max.: 65535 μs
|
1200 to 2400 μs: Idling
|
-
|
| Injection Volume (Cylinder 1)
|
Injection volume (Cylinder 1):
Min.: 0 ml, Max.: 2.047 ml
|
0.05 to 0.15 ml: Idling
|
Total of fuel injection volume of 10 injections
|
| Fuel Pump Speed Control
|
FUEL PMP relay status:
ON or OFF
|
-
|
-
|
| Fuel Pump / Speed Status
|
Fuel pump/status:
ON or OFF
|
ON: Engine running
|
-
|
| EVAP (Purge) VSV
|
Purge VSV control duty:
Min.: 0%, Max.: 100%
|
0 to 100%: Idling
|
Command signal from ECM
|
| Evap Purge Flow
|
Purge flow:
Min.: 0%, Max.: 399.9%
|
0 to 8%: Idling
|
-
|
| Purge Density Learn Value
|
Learning value of purge density:
Min.: -50, Max.: 349.99
|
Idling: -40 to 0
|
-
|
| EVAP Purge VSV
|
Status of purge VSV control:
ON or OFF
|
-
|
-
|
| Target Air-Fuel Ratio
|
Air-Fuel ratio:
Min.: 0, Max.: 1.998
|
0.8 to 1.2: Idling
|
·
1 = Stoichiometric air fuel ratio
|
| AF Lambda B1S1
|
Short-term fuel trim associated with bank 1 sensor 1:
Min.: 0, Max.: 1.99
|
·
Value less than 1 (0.000 to 0.999) = Rich
·
Stoichiometric air-fuel ratio = 1
·
Value greater than 1 (1.001 to 1.99) = Lean
|
-
|
| AF Lambda B2S1
|
Short-term fuel trim associated with bank 2 sensor 1:
Min.: 0, Max.: 1.99
|
·
Value less than 1 (0.000 to 0.999) = Rich
·
Stoichiometric air-fuel ratio = 1
·
Value greater than 1 (1.001 to 1.99) = Lean
|
-
|
| AFS Voltage B1S1
|
Air fuel ratio sensor output voltage for bank 1 sensor 1:
Min.: 0 V, Max.: 7.99 V
|
2.8 to 3.8 V: Idling
|
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
|
| AFS Voltage B2S1
|
Air fuel ratio sensor output voltage for bank 2 sensor 1:
Min.: 0 V, Max.: 7.99 V
|
2.8 to 3.8 V: Idling
|
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
|
| AFS Current B1S1
|
Air fuel ratio sensor current:
Min.: -128 mA, Max.: 127.99 mA
|
-
|
-
|
| AFS Current B2S1
|
Air fuel ratio sensor current:
Min.: -128 mA, Max.: 127.99 mA
|
-
|
-
|
| O2S B1S2
|
Heated oxygen sensor output voltage for bank 1 sensor 2:
Min.: 0 V, Max.: 1.27 V
|
0.1 to 0.9 V:
Driving at 70 km/h (43 mph)
|
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
|
| O2S B2S2
|
Heated oxygen sensor output voltage for bank 2 sensor 2:
Min.: 0 V, Max.: 1.27 V
|
0.1 to 0.9 V:
Driving at 70 km/h (43 mph)
|
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor
|
| Short FT #1
|
Short-term fuel trim of bank 1:
Min.: -100%, Max.: 99.2%
|
-15 to 15%
|
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
|
| Long FT #1
|
Long-term fuel trim of bank 1:
Min.: -100%, Max.: 99.2%
|
-15 to 15%
|
Overall fuel compensation carried out long-term to compensate for a continual deviation of short-term fuel trim from central value
|
| Total FT #1
|
Total fuel trim of bank 1
Average value for fuel trim system of bank 1:
Min.: -0.5, Max.: 0.496
|
-0.28 to 0.2: Idling
|
-
|
| Short FT #2
|
Short-term fuel trim of bank 2:
Min.: -100%, Max.: 99.2%
|
-15 to 15%
|
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
|
| Long FT #2
|
Long-term fuel trim of bank 2:
Min.: -100%, Max.: 99.2%
|
-15 to 15%
|
Overall fuel compensation carried out long-term to compensate for a continual deviation of short-term fuel trim from central value
|
| Total FT #2
|
Total fuel trim of bank 2
Average value for fuel trim system of bank 2:
Min.: -0.5, Max.: 0.496
|
-0.28 to 0.2: Idling
|
-
|
| Fuel System Status #1
|
OL, CL, OLDrive, OLFault or CLFault
|
CL: Idling after warming up
|
·
OL (Open Loop): Has not yet satisfied conditions to go closed loop
·
CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control
·
OLDrive: Open loop due to driving conditions (fuel enrichment)
·
OLFault: Open loop due to detected system fault
·
CLFault: Closed loop but air fuel ratio sensor, which used for fuel control malfunctioning
|
| Fuel System Status #2
|
OL, CL, OLDrive, OLFault or CLFault
|
CL: Idling after warming up
|
·
OL (Open Loop): Has not yet satisfied conditions to go closed loop
·
CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control
·
OLDrive: Open loop due to driving conditions (fuel enrichment)
·
OLFault: Open loop due to detected system fault
·
CLFault: Closed loop but air fuel ratio sensor, which used for fuel control malfunctioning
|
| IGN Advance
|
Ignition timing advance for No. 1 cylinder:
Min.: -64 deg., Max.: 63.5 deg.
|
BTDC 7 to 24: Idling
|
-
|
| Knock Feedback Value
|
Feedback value of knocking:
Min: -64 deg(CA), Max.: 1023 deg(CA)
|
-22 to 0 deg(CA):
Driving at 70 km/h (44 mph)
|
-
|
| Knock Correct Learn Value
|
Correction learning value of knocking:
Min: -64 deg(CA), Max.: 1023 deg(CA)
|
0 to 22 deg(CA)
Driving at 70 km/h (44 mph)
|
-
|
| Idle Spark Advn Ctrl #1
|
Individual cylinder timing advance compensation amount (No. 1):
Min.: 0 deg(CA), Max.: 15.93 deg(CA)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Idle Spark Advn Ctrl #2
|
Individual cylinder timing advance compensation amount (No. 2):
Min.: 0 deg(CA), Max.: 15.93 deg(CA)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Idle Spark Advn Ctrl #3
|
Individual cylinder timing advance compensation amount (No. 3):
Min.: 0 deg(CA), Max.: 15.93 deg(CA)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Idle Spark Advn Ctrl #4
|
Individual cylinder timing advance compensation amount (No. 4):
Min.: 0 deg(CA), Max.: 15.93 deg(CA)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Idle Spark Advn Ctrl #5
|
Individual cylinder timing advance compensation amount (No. 5):
Min.: 0 deg(CA), Max.: 15.93 deg(CA)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Idle Spark Advn Ctrl #6
|
Individual cylinder timing advance compensation amount (No. 6):
Min.: 0 deg(CA), Max.: 15.93 deg(CA)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| ACIS VSV
|
Intake air control valve assembly for acoustic control induction system status:
ON or OFF
|
-
|
-
|
| VVT Control Status #1
|
VVT control (bank 1) status:
ON or OFF
|
-
|
-
|
| VVT Control Status #2
|
VVT control (bank 2) status:
ON or OFF
|
-
|
-
|
| VVT Advance Fail
|
VVT control failure status:
ON or OFF
|
ON: VVT control failure
|
-
|
| VVT Aim Angle #1 (*2)
|
VVT aim angle (Bank 1):
Min.: 0%, Max.: 399.9%
|
-
|
VVT duty signal value during operation
|
| VVT Change Angle #1 (*2)
|
VVT change angle (Bank 1):
Min.: 0 degFR, Max.: 639.9 degFR
|
-
|
Displacement angle during operation
|
| VVT OCV Duty #1 (*2)
|
VVT OCV (Bank 1) operation duty:
Min.: 0%, Max.: 399.9%
|
-
|
Requested duty value for operation
|
| VVT Aim Angle #2 (*2)
|
VVT aim angle (Bank 2):
Min.: 0%, Max.: 399.9%
|
-
|
VVT duty signal value during operation
|
| VVT Change Angle #2 (*2)
|
VVT change angle (Bank 2):
Min.: 0 degFR, Max.: 639.9 degFR
|
-
|
Displacement angle during operation
|
| VVT OCV Duty #2 (*2)
|
VVT OCV (bank 2) operation duty:
Min.: 0%, Max.: 399.9%
|
-
|
Requested duty value for operation
|
| VVT Ex Hold Lrn Val #1 (*2)
|
VVT exhaust hold duty ratio learning value (bank 1):
Min.: 0%, Max.: 399.9%
|
-
|
-
|
| VVT Ex Chg Angle #1 (*2)
|
VVT exhaust change angle (bank 1):
Min.: 0 degFR, Max.: 639.9 degFR
|
-
|
-
|
| VVT Ex OCV Duty #1 (*2)
|
VVT exhaust OCV duty (bank 1):
Min.: 0%, Max.: 399.9%
|
-
|
-
|
| VVT Ex Hold Lrn Val #2 (*2)
|
VVT exhaust hold duty ratio learning value (bank 2):
Min.: 0%, Max.: 399.9%
|
-
|
-
|
| VVT Ex Chg Angle #2 (*2)
|
VVT exhaust change angle (bank 2):
Min.: 0 degFR, Max.: 639.9 degFR
|
-
|
-
|
| VVT Ex OCV Duty #2 (*2)
|
VVT exhaust OCV duty (bank 2):
Min.: 0%, Max.: 399.9%
|
-
|
-
|
| Catalyst Temp B1S1
|
Catalyst temperature (bank 1, sensor 1):
Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F)
|
-
|
-
|
| Catalyst Temp B2S1
|
Catalyst temperature (bank 2, sensor 1):
Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F)
|
-
|
-
|
| Catalyst Temp B1S2
|
Catalyst temperature (bank 1, sensor 2):
Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F)
|
-
|
-
|
| Catalyst Temp B2S2
|
Catalyst temperature (bank 2, sensor 2):
Min.: -40°C (-40°F), Max.: 6513.5°C (11756°F)
|
-
|
-
|
| Starter Signal
|
Starter signal:
ON or OFF
|
ON: Starter signal on
|
-
|
| Starter Control
|
Starter signal status:
ON or OFF
|
-
|
-
|
| Power Steering Signal
|
Power steering signal:
ON or OFF
|
ON: Power steering operation
|
-
|
| Starter Relay
|
Starter relay:
ON or OFF
|
ON: Cranking
|
-
|
| Power Steer. Sig. Record
|
Power steering signal (history):
ON or OFF
|
ON: When steering wheel first turned after battery terminals connected
|
Signal status usually ON until battery terminals disconnected
|
| ACC Relay
|
ACC relay:
ON or OFF
|
ON: Cranking
|
-
|
| Neutral Position SW Signal
|
Park/Neutral position switch assembly status:
ON or OFF
|
ON: Shift lever in P or N
|
-
|
| Stop Light Switch
|
Stop light switch assembly:
ON or OFF
|
ON: Brake pedal depressed
|
-
|
| A/C Signal
|
A/C signal:
ON or OFF
|
ON: A/C ON
|
-
|
| Closed Throttle Position SW
|
Closed throttle position switch:
ON or OFF
|
·
ON: Throttle fully closed
|
-
|
| Electrical Load Signal
|
Electrical load signal:
ON or OFF
|
ON: Headlights or defogger turned on
|
-
|
| Check Mode
|
Check mode:
ON or OFF
|
ON: Check mode on
|
See page ( )
|
| SPD Test Result
|
Check mode result for vehicle speed sensor:
Compl or Incmpl
|
-
|
-
|
| Misfire Test Result
|
Check mode result for misfire monitor:
Compl or Incmpl
|
-
|
-
|
| OXS1 Test Result
|
Check mode result for heated oxygen sensor (bank 1):
Compl or Incmpl
|
-
|
-
|
| OXS2 Test Result
|
Check mode result for heated oxygen sensor (bank 2):
Compl or Incmpl
|
-
|
-
|
| A/F Test Results #2
|
Check mode result for air fuel ratio sensor (Bank 2):
Compl or Incmpl
|
-
|
-
|
| A/F Test Results #1
|
Check mode result for air fuel ratio sensor (Bank 1):
Compl or Incmpl
|
-
|
-
|
| Complete Parts Monitor
|
Comprehensive component monitor:
Not Avl or Avail
|
-
|
-
|
| Fuel System Monitor
|
Fuel system monitor:
Not Avl or Avail
|
-
|
-
|
| Misfire Monitor
|
Misfire monitor:
Not Avl or Avail
|
-
|
-
|
| O2S(A/FS) Monitor
|
O2S (A/FS) monitor/
Not Avl or Avail
|
-
|
-
|
| O2S(A/FS) Monitor
|
O2S (A/FS) Monitor:
Compl or Incmpl
|
-
|
-
|
| Catalyst Monitor
|
Catalyst monitor:
Not Avl or Avail
|
-
|
-
|
| Catalyst Monitor
|
Catalyst Monitor:
Compl or Incmpl
|
-
|
-
|
| # Codes (Include History)
|
# Codes:
Min.: 0, Max.: 255
|
-
|
Number of detected DTCs
|
| MIL
|
MIL status:
ON or OFF
|
ON: MIL on
|
-
|
| MIL ON Run Distance
|
MIL ON run distance:
Min.: 0 km (0 mile),
Max.: 65535 km (40723 mile)
|
Distance after DTC detected
|
-
|
| Running Time from MIL ON
|
Running time from MIL ON:
Min.: 0 min,
Max.: 65535 min
|
Equivalent to running time after MIL ON
|
-
|
| Time After DTC Cleared
|
Time after DTC cleared:
Min.: 0 min,
Max.: 65535 min
|
Equivalent to time after DTCs cleared
|
-
|
| Distance from DTC Cleared
|
Distance after DTC cleared:
Min.: 0 km(0 mile), Max.: 65535 km (40723 mile)
|
Equivalent to drive distance after DTCs cleared
|
-
|
| Warmup Cycle Cleared DTC
|
Warm-up cycle after DTC cleared:
Min.: 0, Max.: 255
|
-
|
Number of warm-up cycles after DTC cleared
|
| OBD Requirements
|
OBD Requirement
|
E-OBD
|
-
|
| Number of Emission DTC
|
Number of emission related DTC
|
-
|
-
|
| TC and TE1
|
TC and TE1 terminal of DLC 3:
ON or OFF
|
-
|
-
|
| Ignition Trig. Count
|
Ignition counter:
Min.: 0, Max.: 65535
|
0 to 600
|
-
|
| Cylinder #1 Misfire Count
|
Misfire count of cylinder 1:
Min.: 0, Max.: 255
|
0
|
-
|
| Cylinder #2 Misfire Count
|
Misfire count of cylinder 2:
Min.: 0, Max.: 255
|
0
|
-
|
| Cylinder #3 Misfire Count
|
Misfire count of cylinder 3:
Min.: 0, Max.: 255
|
0
|
-
|
| Cylinder #4 Misfire Count
|
Misfire count of cylinder 4:
Min.: 0, Max.: 255
|
0
|
-
|
| Cylinder #5 Misfire Count
|
Misfire count of cylinder 5:
Min.: 0, Max.: 255
|
0
|
-
|
| Cylinder #6 Misfire Count
|
Misfire count of cylinder 6:
Min.: 0, Max.: 255
|
0
|
-
|
| All Cylinders Misfire Count
|
All cylinders misfire count:
Min.: 0, Max.: 255
|
0
|
-
|
| Misfire RPM
|
Engine speed when misfire occurs:
Min.: 0 rpm, Max.: 6375 rpm
|
0 rpm: Misfire 0
|
-
|
| Misfire Load
|
Engine load when misfire occurs:
Min.: 0 g/rev, Max.: 3.98 g/rev
|
-
|
-
|
| Misfire Margin
|
Margin to detect engine misfire:
Min.: -100%, Max.: 127%
|
0 to 127%
|
Misfire detection margin
|
| Engine Starting Time
|
Engine run time (elapsed time from engine switch on (IG) to off):
Min.: 0 ms, Max.: 655350 ms
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Engine Speed (Starter Off)
|
Engine speed when starter off:
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Starter Count
|
Number of times starter turned on after engine switch turned from off to ON):
Min.: 0, Max.: 255
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Run Dist of Previous Trip
|
Distance traveled during previous trip:
Min.: 0 km (0mile), Max.: 655.35 km (407 mile)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Previous Trip Coolant Temp
|
Coolant temperature of previous trip:
Min.: -40°C (-40°F), Max.: 215°C (419°F)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Previous Trip Intake Temp
|
Intake air Coolant temperature of previous trip:
Min.: -40°C (-40°F), Max.: 215°C (419°F)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Engine Oil Temperature
|
Engine oil temperature (estimated):
Min.: -40°C (-40°F), Max.: 215°C (419°F)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Previous Trip Eng Oil Temp
|
Engine oil temperature of previous trip (estimated):
Min.: -40°C (-40°F), Max.: 215°C (419°F)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Ambient Temp for A/C
|
Ambient temperature:
Min.: -40°C (-40°F), Max.: 215°C (419°F)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Previous Trip Ambient Temp
|
Ambient temperature of previous trip:
Min.: -40°C (-40°F), Max.: 215°C (419°F)
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Engine Start Hesitation
|
History of hesitation during engine start:
ON or OFF
|
-
|
This value changes to ON when the engine speed does not reach 500 rpm during cranking.
|
| Low Rev for Eng Start
|
History of low engine speed after engine starts:
ON or OFF
|
-
|
-
|
| Minimum Engine Speed
|
Minimum engine speed:
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
When the engine stalls, is difficult to start, or idles roughly
|
| Battery Current
|
Battery current:
Min.: -100 A, Max.: 100 A
|
-
|
-
|
| Battery Temperature
|
Battery temperature:
Min.: -45°C (-49°F), Max.: 156.4°C (313.5°F)
|
-
|
-
|
| Alternator Output Duty
|
Generator output duty:
Min.: 0%, Max.: 100%
|
-
|
-
|
| Alt Vol - Non Active Test
|
Request voltage when regulator not under forced activation:
Min.: 0 V, Max.: 20 V
|
Battery electrolyte temperature varies (12.5 to 14.8 V) while driving: After engine start
|
Alternator regulator output voltage is output
When performing Active Test, value is 0 V
|
| Alt Vol - Active Test
|
Request voltage when regulator under forced activation:
Min.: 0 V, Max.: 20 V
|
Request instruction voltage value: After engine start
|
Charging control service data
When performing Active Test, value is 0 V
|
| Electric Fan Motor
|
Electric fan motor:
ON or OFF
|
-
|
-
|
| Idle Fuel Cut
|
Fuel cut idle:
ON or OFF
|
ON: Fuel cut operation
|
Idle fuel cut = "ON" when throttle valve fully closed and engine speed over 1400 rpm
|
| FC TAU
|
Fuel cut TAU (Fuel cut with a very light load):
ON or OFF
|
ON: Fuel cut operating
|
Fuel cut being performed with a very light load to prevent incomplete engine combustion
|
| Immobiliser Fuel Cut
|
Status of immobiliser fuel cut:
ON or OFF
|
-
|
-
|
| Model Code
|
Model code information
|
GRS 50#
|
-
|
| Engine Type
|
Engine type information
|
2GRFE
|
-
|
| Cylinder Number
|
Cylinder number
Min.: 0, Max.: 255
|
6
|
-
|
| Transmission Type
|
Transmission type
|
ECT 6th
|
-
|
| Destination
|
Destination information
|
W or @
|
-
|
| Model Year
|
Model year:
Min.: 1900, Max.: 2155
|
20##
|
-
|
| System Identification
|
System identification
|
Gasoline (gasoline engine)
|
-
|
| Engine Speed of Cyl #1
|
Engine Speed of Cylinder #1 of Injection Stopped:
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
|
| Engine Speed of Cyl #2
|
Engine Speed of Cylinder #2 of Injection Stopped:
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
|
| Engine Speed of Cyl #3
|
Engine Speed of Cylinder #3 of Injection Stopped:
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
|
| Engine Speed of Cyl #4
|
Engine Speed of Cylinder #4 of Injection Stopped:
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
|
| Engine Speed of Cyl #5
|
Engine Speed of Cylinder #5 of Injection Stopped:
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
|
| Engine Speed of Cyl #6
|
Engine Speed of Cylinder #6 of Injection Stopped:
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
|
| Av Engine Speed of All Cyl
|
Average Engine Speed of All Cylinders of Injection Stopped:
Min.: 0 rpm, Max.: 51199 rpm
|
-
|
Output only when Check the Cylinder Compression performed using Active Test
51199 rpm: Active Test not performed
|
| Received MIL from ECT
|
Received MIL from TCM:
ON or OFF
|
MIL illuminate instruction on signal from TCM: ON
|
-
|
| Shift Position Sig from ECT
|
Received shift position signal from TCM:
1st, 2nd, 3rd, 4th, 5th, or 6th
|
Actual shift position
|
-
|
| A/T Oil Temp from ECT
|
ATF temperature:
Min.: -40°C (-40°F), Max.: 215°C (419°F)
|
-
|
-
|
| SPD (NO)
|
Output shaft speed:
Min.: 0 rpm, Max.: 12750 rpm
|
-
|
-
|
| ECT Lock Up
|
Lock up: ON or OFF
|
-
|
-
|
| Shift SW Status (P Range)
|
Park/neutral position switch assembly switch status:
ON or OFF
|
·
OFF: Shift lever not in P
|
-
|
| Shift SW Status (R Range)
|
Park/neutral position switch assembly switch status:
ON or OFF
|
·
OFF: Shift lever not in R
|
-
|
| Shift SW Status (N Range)
|
Park/neutral position switch assembly switch status:
ON or OFF
|
·
OFF: Shift lever not in N
|
-
|
| Sports Shift Up SW
|
Sports shift up switch status:
ON or OFF
|
"+" pressed continuously: ON
"+" released: OFF
|
-
|
| Sports Shift Down SW
|
Sports shift down switch status:
ON or OFF
|
"-" pressed continuously: ON
"-" released: OFF
|
-
|
| Sports Mode Selection SW
|
Sports mode select switch status:
ON or OFF
|
·
ON: Shift lever in S, "+" or "-"
·
OFF: Shift lever not in S, "+" and "-"
|
-
|
| Shift SW Status (D Range)
|
Park/neutral position switch assembly switch status:
ON or OFF
|
·
ON: Shift lever in D or S
·
OFF: Shift lever not in D or S
|
-
|