Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › from 2014.09
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  U0101  Lost Communication with TCM  


DESCRIPTION

The Transmission Control Module (TCM) and ECM perform 2-way communications with each other via the Controller Area Network (CAN). The TCM sends signals to the ECM concerning required engine speed, required engine torques, warning indicators in the combination meter assembly, DTCs and other data. The ECM sends signals to the TCM concerning engine speed, opening angles of the throttle valve, temperature of intake air, temperature of engine coolant, engine torques and other data. If the TCM cannot communicate with the ECM, the TCM will conclude that there is a malfunction in the CAN system, illuminate the MIL and store a DTC.

DTC No. DTC Detection Condition Trouble Area
U0101 No communication from TCM continues (1 trip detection logic)
·

Open or short in TCM and ECM circuit

·

TCM

·

ECM



WIRING DIAGRAM

A159636E03
1.438,1.073 1.635,1.26 0.198,0.188 10 false D5 1.438,1.729 1.635,1.917 0.198,0.188 10 false D5 1.438,2.125 1.635,2.313 0.198,0.188 10 false D5 1.438,2.5 1.635,2.688 0.198,0.188 10 false D5 0.948,1.073 1.313,1.26 0.365,0.188 10 false CAN- 6.073,1.063 6.438,1.25 0.365,0.188 10 false CAN- 1.469,0.875 1.615,1.063 0.146,0.188 10 false 7 5.771,1.083 5.979,1.271 0.208,0.188 10 false D1 5.771,1.729 5.979,1.917 0.208,0.188 10 false D1 5.813,0.875 5.917,1.063 0.104,0.188 10 false 1 6.073,1.729 6.552,1.917 0.479,0.188 10 false CAN+ 5.813,1.542 5.917,1.729 0.104,0.188 10 false 2 0.927,1.74 1.333,1.927 0.406,0.188 10 false CAN+ 1.479,1.552 1.625,1.74 0.146,0.188 10 false 6 0.927,2.115 1.333,2.302 0.406,0.188 10 false BATT 0.771,2.927 1.104,3.073 0.333,0.146 10 false TCM 6.302,2.927 6.698,3.115 0.396,0.188 10 false ECM 3.24,2.271 3.49,2.458 0.25,0.188 10 false EFI 1.479,1.938 1.625,2.125 0.146,0.188 10 false 1 1.104,2.5 1.344,2.688 0.24,0.188 10 false E1 1.479,2.323 1.625,2.51 0.146,0.188 10 false 8

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTC OUTPUT (IN ADDITION TO DTC U0101)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / DTC.


e.

Read the DTCs.

Result
Result Proceed to
DTC U0101 is output A
DTC U0101 and other DTCs are output B



A

2.CHECK TERMINAL VOLTAGE (+B OF TCM)

B

2.CHECK TERMINAL VOLTAGE (+B OF TCM)
a.
U189043E01
0.102,0.006 1.407,0.145 1.305,0.139 10 Wire Harness Side: 0.639,0.303 2.442,0.448 1.803,0.145 10 TCM Connector (Front View) 0.182,0.78 0.391,0.925 0.209,0.145 10 D5 2.164,1.911 2.549,2.060 0.385,0.149 10 BATT 1.529,1.255 2.147,1.984 false 0.465,1.911 0.653,2.060 0.188,0.149 10 E1 1.064,1.335 0.699,1.984 false

Disconnect the TCM connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D5-1 (BATT) - D5-8 (E1) Engine switch on (IG) 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (TCM - ECM)

NG

REPAIR OR REPLACE ECU POWER SOURCE CIRCUIT (TCM POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (TCM - ECM)
a.

Disconnect the TCM connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D5-6 (CAN+) - D1-2 (CAN+) Always Below 1 Ω
D5-7 (CAN-) - D1-1 (CAN-) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D5-6 (CAN+) or D1-2 (CAN+) - Body ground Always 10 kΩ or higher
D5-7 (CAN-) or D1-1 (CAN-) - Body ground Always 10 kΩ or higher




OK

4.REPLACE TCM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE TCM

NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0101)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0101)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off.


f.

Turn the engine switch on (IG).


g.

Turn the tester on.


h.

Wait for 5 seconds or more.


i.

Enter the following menus: Powertrain / Engine / DTC.


j.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC U0101 is output B



A

END

B