Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P1585  Acceleration Sensor Circuit  P1586  Acceleration Sensor Malfunction  


DESCRIPTION

The ECM detects the yaw rate based on a signal sent from the yaw rate sensor and uses this information for neutral control. If the ECM detects a malfunction based on a fault signal sent from the skid control ECU, the ECM prohibits neutral control as a fail-safe function.

The skid control ECU supplies power to the yaw rate sensor and records the sensor data. The data is shared by the ECM via CAN. Zero point calibration and operation is performed by each ECU.

HINT:

If a CAN communication DTC is output, perform troubleshooting for that DTC first.


DTC Code DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P1585
1.

Engine switch on (IG).

2.

The output value of the yaw rate sensor remains at -1.5 G or less, or 1.5 G or more for at least 1.2 seconds.

3.

0.5 seconds

4.

1 trip detection logic


·

Yaw rate sensor circuit

·

Yaw rate sensor

·

Brake actuator assembly (Skid control ECU)

·

CAN communication system

·

ECM


1.

Engine switch on (IG).

2.

The power source voltage to the yaw rate sensor remains at 4.4 V or less, or 5.6 V or higher for at least 1.2 seconds.

3.

0.5 seconds

4.

1 trip detection logic


1.

Engine switch on (IG).

2.

No signal from the yaw rate sensor is detected 7 times or more.

3.

0.5 seconds

4.

1 trip detection logic


1.

Engine switch on (IG).

2.

With the vehicle stopped, the difference between GL1 and GL2 does not become less than 0.4 G within 60 seconds after exceeding 0.6 G.

3.

0.5 seconds

4.

1 trip detection logic


1.

Engine switch on (IG).

2.

A yaw rate sensor power source voltage malfunction signal is received for at least 10 seconds with the vehicle speed at 3 km/h (1.8 mph) or more.

3.

0.5 seconds

4.

1 trip detection logic


P1586
1.

Engine switch on (IG)

2.

With the vehicle speed 30 km/h (18 mph) or more, the difference between the longitudinal acceleration calculated based on the yaw rate sensor value and the longitudinal acceleration calculated based on the vehicle speed exceeds 0.35 G for 60 seconds or more.

3.

0.5 seconds

4.

1 trip detection logic


1.

Engine switch on (IG)

2.

No change detected in the yaw rate sensor signal 16 times or more while the vehicle speed decreases from 30 km/h (18 mph) to 0 km/h (0 mph).

3.

0.5 seconds

4.

1 trip detection logic



WIRING DIAGRAM

A239011E01
5.903,2.518 6.293,2.720 0.390,0.202 10 ECM 1.736,3.194 2.860,3.430 1.123,0.237 10 Yaw Rate Sensor 1.574,1.554 4.496,1.915 2.922,0.361 10 Brake Actuator Assembly (Skid Control ECU) 4.915,3.299 6.755,3.500 1.840,0.202 10 : CAN Communication Line 1.36,1.559 1.594,1.761 0.233,0.202 10 A9 2.475,0.532 2.936,0.734 0.460,0.202 10 CANH 5.6,0.532 6.060,0.734 0.460,0.202 10 CANH 2.458,2.227 2.918,2.429 0.460,0.202 10 CANH 2.475,1.089 2.936,1.290 0.460,0.202 10 CANL 5.6,1.125 6.060,1.327 0.460,0.202 10 CANL 2.458,2.841 2.918,3.043 0.460,0.202 10 CANL 2.955,0.35 3.186,0.551 0.231,0.202 10 35 5.337,0.35 5.568,0.551 0.231,0.202 10 41 5.337,0.924 5.568,1.126 0.231,0.202 10 49 2.955,2.066 3.186,2.268 0.231,0.202 10 2 2.955,2.696 3.186,2.898 0.231,0.202 10 3 2.955,0.938 3.186,1.140 0.231,0.202 10 14 5.697,2.518 5.930,2.720 0.233,0.202 10 A7 1.455,3.194 1.758,3.396 0.303,0.202 10 N21

PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch to on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / DTC.


e.

Read the DTCs.


f.

Check for DTCs of the CAN communication system (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

Result
Result Proceed to
DTC is not output A
DTC is output (vehicle stability control system) B
DTC is output (CAN communication system) C

HINT:
·

If the VSC system stores a yaw rate sensor system DTC, the yaw rate sensor or skid control ECU may be malfunctioning.

·

The skid control ECU stores DTCs to indicate a yaw rate sensor power malfunction, stuck malfunction or abnormal output value.

·

Check carefully when any DTCs indicating an ECU power malfunction or ECU internal malfunction are output.

·

If DTC P1589 (abnormal acceleration sensor learning value) is output with other DTCs, perform zero point calibration of the yaw rate sensor first (deceleration sensor zero point calibration).





A

2.PERFORM INITIALIZATION

B

C

2.PERFORM INITIALIZATION
a.

Perform zero point calibration of the yaw rate sensor (deceleration sensor zero point calibration) (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>INITIALIZATION).



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P1585 OR P1586)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P1585 OR P1586)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch to on (IG).


c.

Turn the tester on.



e.

Drive the vehicle.


f.

Enter the following menus: Powertrain / Engine / DTC.


g.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC P1585 or P1586 is output B



A

END

B