Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › MASS AIR FLOW METER
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291783 MASS AIR FLOW METER G

2AZ-FE ENGINE CONTROL  MASS AIR FLOW METER  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:
·

Perform the MAF meter inspection according to the procedures below.

·

Only replace the MAF meter when both the Long FT#1 value and MAF value in the Data List (with the engine stopped) are not within the normal operating range.



PROCEDURE

Hide 22204 1.INSPECT MASS AIR FLOW METER

a.

Perform confirmation driving pattern.

i.
B135940E01
0.425,2.845 1.557,3.021 1.132,0.177 10 Intelligent Tester 0.6,2.589 0.6,2.832 false 1.48,2.058 1.864,2.214 0.385,0.156 10 DLC3 1.717,2.051 1.841,1.732 false

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch on (IG).


iii.

Turn the tester ON.



v.

Start the engine and warm it up with all accessory switches OFF until the engine coolant temperature is 75°C (167°F) or more.


vi.

Drive the vehicle at 50 km/h (31 mph) or more for 3 to 5 minutes*1.


vii.

Allow the engine to idle for 2 minutes*2.


viii.

Perform steps *1 and *2 at least 3 times.

A116436E30
1.531,2.25 1.271,2.063 false 0.479,0.625 1.677,0.823 1.198,0.198 10 false (Vehicle Speed) 0.344,1.594 1.521,1.823 1.177,0.229 10 false 50 km/h (31 mph) 1.813,2.948 2.604,3.135 0.792,0.188 10 false Warming up 0.885,1.896 1.302,2.094 0.417,0.198 10 false Idling 0.24,2.354 1.479,2.521 1.24,0.167 10 false Ignition Switch Off 5.49,3.135 6.667,3.302 1.177,0.167 10 false *1: 3 to 5 minutes 5.49,3.479 6.385,3.646 0.896,0.167 10 false *2: 2 minutes 2.885,0.958 3.125,1.177 0.24,0.219 10 false *1 4.073,0.958 4.313,1.177 0.24,0.219 10 false *1 5.271,0.958 5.51,1.177 0.24,0.219 10 false *1 3.479,2.583 3.719,2.802 0.24,0.219 10 false *2 4.667,2.583 4.906,2.802 0.24,0.219 10 false *2 5.865,2.583 6.104,2.802 0.24,0.219 10 false *2



b.

Read the value using the intelligent tester (Long FT#1).

i.

Select the following menu items: Powertrain / Engine and ECT / Data List / Primary / Long FT#1.


ii.

Read the values displayed on the tester.

Standard value:

Within -15 to +15%


If the result is not within the specified range, perform the inspection below.



c.

Read the value using the intelligent tester (MAF).

NOTICE:
·

Turn off the engine.

·

Perform the inspection with the vehicle indoors and on a level surface.

·

Perform the inspection of the MAF meter while it is installed to the air cleaner case (installed to the vehicle).

·

During the test, do not use the exhaust air duct to perform suction on the exhaust pipe.



i.

Turn the ignition switch on (ACC).


ii.

Turn the ignition switch on (IG) (do not start the engine).


iii.

Turn the tester ON.


iv.

Select the following menu items: Powertrain / Engine and ECT / Data List / Primary / MAF.


v.

Wait 30 seconds, and read the values on the intelligent tester.

Standard condition:

Below 0.42 g/sec.


·

If the result is not as specified, replace the MAF meter.

·

If the result is within the specified range, inspect the cause of the extremely rich or lean air-fuel ratio (see page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>P0171).