Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM J

2AZ-FE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the engine switch is turned on (IG), the battery voltage is applied to the IGSW of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contacts of the integration relay (EFI MAIN relay) and supplying power to either terminal +B or +B2 of the ECM.

WIRING DIAGRAM

A192505E11
0.875,1.771 1.958,2.01 1.083,0.24 10 false Main Body ECU 0.875,1.625 1.167,1.771 0.292,0.146 10 false G58 1.406,1.208 1.76,1.365 0.354,0.156 10 false IG2D 1.813,1.125 2.052,1.271 0.24,0.146 10 false 11 0.615,2.719 1.25,2.875 0.635,0.156 10 false F/B BATT 0.615,3.104 1.25,3.26 0.635,0.156 10 false FL MAIN 0.708,3.646 1.229,3.802 0.521,0.156 10 false Battery 1.781,2.573 2.042,2.729 0.26,0.156 10 false EFI 2.823,3.292 3.458,3.448 0.635,0.156 10 false EFI MAIN 3.406,2.344 3.5,2.49 0.094,0.146 10 false 3 3.406,2.906 3.5,3.052 0.094,0.146 10 false 1 2.771,2.344 2.865,2.49 0.094,0.146 10 false 5 2.771,2.906 2.865,3.052 0.094,0.146 10 false 2 2.99,1.479 3.25,1.635 0.26,0.156 10 false IG2 2.052,0.771 2.313,0.927 0.26,0.156 10 false IG2 4.385,0.781 4.677,0.938 0.292,0.156 10 false IGN 3.406,0.563 3.5,0.708 0.094,0.146 10 false 3 3.406,1.125 3.5,1.271 0.094,0.146 10 false 2 2.771,0.563 2.865,0.708 0.094,0.146 10 false 5 2.771,1.125 2.865,1.271 0.094,0.146 10 false 1 5.688,0.646 6.083,0.802 0.396,0.156 10 false IGSW 5.688,1.885 5.979,2.042 0.292,0.156 10 false +B 5.688,2.438 5.979,2.594 0.292,0.156 10 false +B2 5.688,3 6.115,3.156 0.427,0.156 10 false MREL 5.688,3.656 5.979,3.813 0.292,0.156 10 false E1 5.385,3.646 5.604,3.802 0.219,0.156 10 false D2 5.385,3.01 5.594,3.167 0.208,0.156 10 false A7 5.396,2.427 5.615,2.583 0.219,0.156 10 false A7 5.385,1.865 5.583,2.021 0.198,0.156 10 false A7 5.396,0.646 5.583,0.802 0.188,0.156 10 false A7 6.104,4.208 6.49,4.365 0.385,0.156 10 false ECM 5.396,0.469 5.583,0.615 0.188,0.146 10 false 28 5.438,1.698 5.531,1.844 0.094,0.146 10 false 2 5.438,2.26 5.531,2.406 0.094,0.146 10 false 1 5.385,2.833 5.573,2.979 0.188,0.146 10 false 44 5.333,3.458 5.563,3.604 0.229,0.146 10 false 104

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - EFI FUSE)
a.
A137346E01
0.346,0.367 2.461,0.562 2.115,0.194 10 Engine Room No. 1 Relay Block 0.232,3.212 0.965,3.413 0.733,0.201 10 EFI Fuse

Remove the EFI fuse from the engine room No. 1 relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
EFI fuse terminal (1) - Body ground Always 11 to 14 V




OK

2.INSPECT FUSE (EFI)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT FUSE (EFI)

OK

3.INSPECT EFI MAIN RELAY

NG

REPLACE FUSE

3.INSPECT EFI MAIN RELAY
B016200

a.

Remove the EFI MAIN relay from the engine room No. 1 relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
3 - 5 10 kΩ or higher
3 - 5 Below 1 Ω
(When battery voltage applied to terminals 1 and 2)




OK

4.CHECK HARNESS AND CONNECTOR (+B, +B2 AND MREL CIRCUIT)

NG

REPLACE EFI MAIN RELAY

4.CHECK HARNESS AND CONNECTOR (+B, +B2 AND MREL CIRCUIT)
a.

Remove the EFI MAIN relay from the engine room No. 1 relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A7-44 (MREL) - EFI MAIN relay terminal (1) Always Below 1Ω
A7-2 (+B) - EFI MAIN relay terminal (3)
A7-1 (+B2) - EFI MAIN relay terminal (3)


Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
EFI MAIN relay terminal (2) - Body ground Always Below 1Ω




OK

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D2-104 (E1) - Body ground Always Below 1Ω




OK

6.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT ECM (IGSW VOLTAGE)
a.
U188264E02
2.01,1.792 2.417,2.26 false 2.24,3.552 2.698,3.333 false 0.063,0.052 1.385,0.271 1.323,0.219 10 false Wire Harness Side 1.333,0.542 2.406,0.76 1.073,0.219 10 false ECM Connector 2.385,2.292 2.604,2.469 0.219,0.177 10 false E1 2.771,3.229 3.198,3.406 0.427,0.177 10 false IGSW 1.479,2.646 2.552,2.865 1.073,0.219 10 false ECM Connector 1.177,2.146 1.906,2.365 0.729,0.219 10 false Front View 1.427,4.302 2.156,4.521 0.729,0.219 10 false Front View 0.802,0.542 1.052,0.719 0.25,0.177 10 false D2 0.948,2.656 1.177,2.833 0.229,0.177 10 false A7

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-28 (IGSW) - D2-104 (E1) Engine switch on (IG) 11 to 14 V




NG

7.INSPECT FUSE (IGN AND IG2 FUSE)

OK

7.INSPECT FUSE (IGN AND IG2 FUSE)
a.
A135001E02
1.852,1.643 1.92,1.843 0.068,0.2 1.92,1.762 2.143,2.4 2.143,2.4 2.31,2.4 false 0.06,0.014 2.494,0.351 2.434,0.337 10 Main Body ECU (Instrument Panel Junction Block RH) 2.354,2.304 2.990,2.465 0.636,0.160 10 IGN Fuse

Remove the IGN fuse from the main body ECU (instrument panel junction block RH).


b.
A135000E08
1.49,2.75 1.531,2.958 0.042,0.208 1.552,2.833 2.344,2.958 2.344,2.958 2.5,2.958 false 0.365,0.021 2.49,0.323 2.125,0.302 10 true Engine Room No. 1 Relay Block 2.521,2.885 3.125,3.052 0.604,0.167 10 false IG2 Fuse

Remove the IG2 fuse from the engine room No. 1 relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:

Below 1Ω




OK

8.INSPECT IG2 RELAY

NG

CHECK FOR SHORT IN ALL HARNESSES AND COMPONENTS CONNECTED TO FUSE, AND REPLACE FUSE

8.INSPECT IG2 RELAY
B016200

a.

Remove the IG2 relay from the engine room No. 1 relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
3 - 5 10 kΩ or higher
3 - 5 Below 1 Ω
(When battery voltage applied to terminals 1 and 2)




OK

9.CHECK HARNESS AND CONNECTOR (ECM - ENGINE ROOM NO. 1 RELAY BLOCK)

NG

REPLACE IG2 RELAY

9.CHECK HARNESS AND CONNECTOR (ECM - ENGINE ROOM NO. 1 RELAY BLOCK)
A393994E01
4.625,0.875 5,1.125 0.375,0.25 6.375,1.813 5.865,1.604 false 1.385,0.094 3.667,0.365 2.281,0.271 10 false Engine Room No. 1 Relay Block 0.656,0.958 2.344,1.219 1.688,0.26 10 false IG2 Relay Holder 5.188,0.917 6.875,1.177 1.688,0.26 10 false ECM Connector 4.427,0.479 6.115,0.74 1.688,0.26 10 false Wire Harness Side 6.438,1.76 7.021,2.052 0.583,0.292 10 false IGSW 5.25,2.281 6.198,2.563 0.948,0.281 10 false Front View 4.729,0.906 5.313,1.198 0.583,0.292 10 false A7

a.

Remove the IG2 relay from the engine room No. 1 relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
IG2 relay terminal (3) - A7-28 (IGSW) Always Below 1 Ω




NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

10.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK - MAIN BODY ECU)
10.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK - MAIN BODY ECU)
a.

Remove the IG2 relay from the engine room No. 1 relay block.


b.

Remove the instrument panel junction block (main body ECU).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
IG2 relay terminal (1) - G58-11 (IG2D) Always Below 1Ω
IG2 relay terminal (2) - Body ground Always Below 1Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
G58-11 (IG2D) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
OK (w/ Engine switch) A
OK (w/o Engine switch) B
NG C




A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR