Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0351 is output, check the ignition coil (No. 1 cylinder) circuit.

·

If DTC P0352 is output, check the ignition coil (No. 2 cylinder) circuit.

·

If DTC P0353 is output, check the ignition coil (No. 3 cylinder) circuit.

·

If DTC P0354 is output, check the ignition coil (No. 4 cylinder) circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A255924E28
4.427,1.385 4.375,0.948 4.375,0.948 4.302,0.948 false 5.396,1.135 5.563,0.792 5.563,0.792 5.635,0.792 false 3.854,0.854 4.458,1.01 0.604,0.156 10 false Igniter 4.51,0.531 5.323,0.708 0.813,0.177 10 false from Battery 5.677,0.688 6.875,1.104 1.198,0.417 10 false Ignition Coil (No. 1 Cylinder) 5.615,1.844 6.729,2.021 1.115,0.177 10 false No. 1 Spark Plug 5.615,3.083 6.729,3.26 1.115,0.177 10 false No. 2 Spark Plug 5.615,4.385 6.729,4.563 1.115,0.177 10 false No. 3 Spark Plug 5.615,5.698 6.729,5.875 1.115,0.177 10 false No. 4 Spark Plug 2.74,5.938 3.083,6.115 0.344,0.177 10 false ECM 2.875,1.448 3.24,1.604 0.365,0.156 10 false IGT1 2.875,1.76 3.25,1.906 0.375,0.146 10 false IGF1 0.302,1.344 2.031,1.51 1.729,0.167 10 false Crankshaft Position Sensor 0.313,3.146 2.042,3.313 1.729,0.167 10 false Camshaft Position Sensor 2.865,2.771 3.229,2.927 0.365,0.156 10 false IGT2 2.875,5.417 3.24,5.573 0.365,0.156 10 false IGT4 2.865,4.104 3.229,4.26 0.365,0.156 10 false IGT3 0.188,4.365 2.146,5.188 1.958,0.823 10 false Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter, Throttle Position Sensor, etc.) 3.865,3.344 5.781,3.573 1.917,0.229 10 false Ignition Coil (No. 2 Cylinder) 3.854,5.969 6.031,6.198 2.177,0.229 10 false Ignition Coil (No. 4 Cylinder) 3.854,4.646 5.938,4.875 2.083,0.229 10 false Ignition Coil (No. 3 Cylinder)

DTC No. DTC Detection Condition Trouble Area
P0351
P0352
P0353
P0354
No IGF signal to ECM while engine running
(1 trip detection logic)
·

Ignition system

·

Open or short in IGF1 or IGT circuit (1 to 4) between ignition coil and ECM

·

No. 1 to No. 4 ignition coils

·

ECM



A395440E01
0.458,0.188 1.01,0.458 0.552,0.271 10 false 2 V/DIV. 0.802,0.635 1.354,0.906 0.552,0.271 10 false IGT 0.625,0.885 1.177,1.156 0.552,0.271 10 false GND 1.75,1.844 2.99,2.083 1.24,0.24 10 false 20 msec./DIV. 0.833,1.198 1.385,1.469 0.552,0.271 10 false IGF1 0.625,1.469 1.177,1.74 0.552,0.271 10 false GND


Reference: Inspection using an oscilloscope.

While idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.

Item Content
Terminals CH1:
D2-85 (IGT1) - D2-104 (E1)
D2-84 (IGT2) - D2-104 (E1)
D2-83 (IGT3) - D2-104 (E1)
D2-82 (IGT4) - D2-104 (E1)
CH2:
D2-81 (IGF1) - D2-104 (E1)
Equipment Settings 2 V/DIV.
20 msec./DIV.
Conditions Idling


WIRING DIAGRAM

A286424E02
5.344,1.156 5.688,1.354 0.344,0.198 10 false IGT1 3.052,1.719 4.354,1.906 1.302,0.188 10 false No. 1 Ignition Coil 2.802,0.896 2.906,1.094 0.104,0.198 10 false 1 2.802,1.271 2.906,1.469 0.104,0.198 10 false 4 2.948,0.979 3.156,1.177 0.208,0.198 10 false +B 2.948,1.354 3.292,1.573 0.344,0.219 10 false GND 3.646,0.979 3.99,1.177 0.344,0.198 10 false IGT1 3.729,1.344 3.979,1.542 0.25,0.198 10 false IGF 4.021,1.271 4.125,1.469 0.104,0.198 10 false 2 4.021,0.896 4.125,1.094 0.104,0.198 10 false 3 2.802,2.313 2.906,2.51 0.104,0.198 10 false 1 2.813,2.656 2.917,2.854 0.104,0.198 10 false 4 2.948,2.385 3.156,2.583 0.208,0.198 10 false +B 2.948,2.75 3.292,2.969 0.344,0.219 10 false GND 3.646,2.385 3.99,2.583 0.344,0.198 10 false IGT2 3.052,3.125 4.344,3.323 1.292,0.198 10 false No. 2 Ignition Coil 4.021,2.646 4.125,2.844 0.104,0.198 10 false 2 4.021,2.313 4.125,2.51 0.104,0.198 10 false 3 0.479,0.99 0.646,1.188 0.167,0.198 10 false A 5.333,2.552 5.698,2.75 0.365,0.198 10 false IGT2 5.094,2.333 5.281,2.531 0.188,0.198 10 false 84 5.333,3.927 5.677,4.125 0.344,0.198 10 false IGT3 5.094,3.698 5.281,3.896 0.188,0.198 10 false 83 5.073,6.49 5.271,6.688 0.198,0.198 10 false 81 5.333,6.729 5.677,6.927 0.344,0.198 10 false IGF1 5.094,5.104 5.281,5.302 0.188,0.198 10 false 82 5.073,0.938 5.271,1.135 0.198,0.198 10 false 85 5.625,7.219 5.833,7.417 0.208,0.198 10 false D2 3.729,2.729 3.979,2.927 0.25,0.198 10 false IGF 2.823,3.698 2.927,3.896 0.104,0.198 10 false 1 2.823,4.052 2.927,4.25 0.104,0.198 10 false 4 4.031,4.031 4.135,4.229 0.104,0.198 10 false 2 4.021,3.698 4.125,3.896 0.104,0.198 10 false 3 2.802,5.427 2.906,5.625 0.104,0.198 10 false 4 4.021,5.427 4.125,5.625 0.104,0.198 10 false 2 4.021,5.104 4.125,5.302 0.104,0.198 10 false 3 3.656,3.781 4,3.979 0.344,0.198 10 false IGT3 3.74,4.115 3.99,4.313 0.25,0.198 10 false IGF 2.948,3.781 3.156,3.979 0.208,0.198 10 false +B 2.948,4.115 3.292,4.333 0.344,0.219 10 false GND 3.646,5.177 3.99,5.375 0.344,0.198 10 false IGT4 3.729,5.5 3.979,5.698 0.25,0.198 10 false IGF 2.948,5.177 3.156,5.375 0.208,0.198 10 false +B 2.948,5.5 3.292,5.719 0.344,0.219 10 false GND 3.052,4.5 4.344,4.698 1.292,0.198 10 false No. 3 Ignition Coil 3.052,5.906 4.344,6.104 1.292,0.198 10 false No. 4 Ignition Coil 5.333,5.333 5.677,5.531 0.344,0.198 10 false IGT4 5.906,7.219 6.271,7.417 0.365,0.198 10 false ECM 2.729,1.719 3.021,1.865 0.292,0.146 10 false D26 2.729,3.125 3.021,3.271 0.292,0.146 10 false D27 2.729,4.5 3.021,4.646 0.292,0.146 10 false D28 2.729,5.917 3.021,6.063 0.292,0.146 10 false D29 2.813,5.094 2.917,5.292 0.104,0.198 10 false 1

A192221E06
0.573,1.396 1.208,1.552 0.635,0.156 10 false F/B BATT 0.656,2.792 1.146,2.948 0.49,0.156 10 false Battery 3.396,1.479 3.656,1.708 0.26,0.229 10 false IG2 3.042,0.604 3.208,0.792 0.167,0.188 10 false 5 3.885,0.604 4.052,0.792 0.167,0.188 10 false 3 3.885,1.052 4.052,1.24 0.167,0.188 10 false 1 3.042,1.073 3.208,1.26 0.167,0.188 10 false 2 1.594,0.823 1.854,1.052 0.26,0.229 10 false IG2 4.813,2.51 5.167,2.667 0.354,0.156 10 false IG2D 5.219,2.417 5.417,2.604 0.198,0.188 10 false 11 6.438,0.688 6.635,0.875 0.198,0.188 10 false A 4.25,3.063 4.573,3.219 0.323,0.156 10 false G58 4.25,3.219 5.281,3.385 1.031,0.167 10 false Main Body ECU 0.573,2.073 1.208,2.229 0.635,0.156 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT IGNITION COIL (POWER SOURCE)
U188223E02
1.344,1.177 1.344,1.521 true 2.042,1.177 2.125,1.51 true 0.063,0.052 1.271,0.26 1.208,0.208 10 false Wire Harness Side 0.906,0.344 2.375,0.542 1.469,0.198 10 false Ignition Coil Connector 1.417,1.792 2.229,1.99 0.813,0.198 10 false Front View 1.156,1.531 1.635,1.729 0.479,0.198 10 false +B (+) 1.938,1.542 2.438,1.719 0.5,0.177 10 false GND (-) 0.594,1.031 0.865,1.208 0.271,0.177 10 false D27 0.156,1.031 0.427,1.208 0.271,0.177 10 false D26 0.594,1.323 0.875,1.5 0.281,0.177 10 false D29 0.156,1.323 0.427,1.5 0.271,0.177 10 false D28

a.

Disconnect the ignition coil connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D26-4 (GND) - Body ground Always Below 1 Ω
D27-4 (GND) - Body ground
D28-4 (GND) - Body ground
D29-4 (GND) - Body ground



c.

Turn the engine switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D26-1 (+B) - D26-4 (GND) Engine switch on (IG) 11 to 14 V
D27-1 (+B) - D27-4 (GND)
D28-1 (+B) - D28-4 (GND)
D29-1 (+B) - D29-4 (GND)




OK

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL - ECM)
a.

Disconnect the ignition coil connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D26-2 (IGF) - D2-81 (IGF1) Always Below 1 Ω
D27-2 (IGF) - D2-81 (IGF1)
D28-2 (IGF) - D2-81 (IGF1)
D29-2 (IGF) - D2-81 (IGF1)


Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D26-3 (IGT1) - D2-85 (IGT1) Always Below 1 Ω
D27-3 (IGT2) - D2-84 (IGT2)
D28-3 (IGT3) - D2-83 (IGT3)
D29-3 (IGT4) - D2-82 (IGT4)


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D26-2 (IGF) or D2-81 (IGF1) - Body ground Always 10 kΩ or higher
D27-2 (IGF) or D2-81 (IGF1) - Body ground
D28-2 (IGF) or D2-81 (IGF1) - Body ground
D29-2 (IGF) or D2-81 (IGF1) - Body ground


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D26-3 (IGT1) or D2-85 (IGT1) - Body ground Always 10 kΩ or higher
D27-3 (IGT2) or D2-84 (IGT2) - Body ground
D28-3 (IGT3) or D2-83 (IGT3) - Body ground
D29-3 (IGT4) or D2-82 (IGT4) - Body ground




OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester ON.



d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Shuffle arrangement of the ignition coils with igniters (among No. 1 to No. 4 cylinders).

NOTICE:

Do not shuffle the connectors.



f.

Perform a simulation test.


g.

Check DTCs displayed on the tester.

Result:
Display (DTC Output) Proceed to
Same DTC output A
Different ignition coil DTC output B




A

B