The Mass Air Flow (MAF) meter is a sensor that measures the amount of air flowing through the throttle valve. The ECM uses this information to determine fuel injection duration and to provide an appropriate air fuel ratio.
Inside the mass air flow meter, there is a heated platinum wire which is exposed to the flow of intake air. By applying a specific electrical current to the wire, the ECM heats it to a specific temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.
The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.
When any of these DTCs is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0100 | MAF meter voltage less than 0.2 V, or more than 4.9 V for 3 seconds
(1 trip detection logic) |
·
Open or short in MAF meter circuit ·
MAF meter ·
ECM |
| P0102 | MAF meter voltage less than 0.2 V for 3 seconds
(1 trip detection logic) |
·
Open or short in MAF meter circuit ·
MAF meter ·
ECM |
| P0103 | MAF meter voltage more than 4.9 V for 3 seconds
(1 trip detection logic) |
·
Open or short in MAF meter circuit ·
MAF meter ·
ECM |
When any of these DTCs are set, check the air-flow rate by selecting the following menu items on the intelligent tester: Powertrain / Engine and ECT / Data List / MAF.
| Mass Air Flow Rate (gm/sec.) | Malfunction |
|---|---|
| Approximately 0.0 | ·
Open in MAF meter power source circuit ·
Open or short in VG circuit |
| 271.0 or more | ·
Open in E2G circuit |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
|---|---|
| DTC P0102 is output (P0100 and P0102 are output) | A |
| DTC P0103 is output (P0100 and P0103 are output) | B |
A
B
Disconnect the Mass Air Flow (MAF) meter connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D3-3 (+B) - Body ground | Engine switch on (IG) | 11 to 14 V |
OK
NG
Disconnect the MAF meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D3-5 (VG) - D2-118 (VG) | Always | Below 1 Ω |
| D3-4 (E2G) - D2-116 (E2G) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D3-5 (VG) or D2-118 (VG) - Body ground | Always | 10 kΩ or higher |
OK
NG
Inspect the mass air flow meter, referring to the On-vehicle Inspection for Mass Air Flow Meter (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>MASS AIR FLOW METER>ON-VEHICLE INSPECTION).
Inspect the function of the mass air flow meter.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.
Start the engine.
Check that the MAF value changes when the engine is raced.
The reading changes.
OK
NG
Disconnect the MAF meter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D3-4 (E2G) - Body ground | Always | Below 1 Ω |
OK
NG
Disconnect the MAF meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D3-4 (E2G) - D2-116 (E2G) | Always | Below 1 Ω |
OK
NG