Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0115  Engine Coolant Temperature Circuit  P0117  Engine Coolant Temperature Circuit Low Input  P0118  Engine Coolant Temperature Circuit High Input  


DESCRIPTION

A thermistor, whose resistance value varies according to the Engine Coolant Temperature (ECT), is built into the ECT sensor. The structure of the sensor and its connection to the ECM are the same as those of the intake air temperature sensor.

HINT:

When DTC P0115, P0117 or P0118 is stored, the ECM enters fail-safe mode. During fail-safe mode, the engine coolant temperature is estimated to be 80°C (176°F) by the ECM. Fail-safe mode continues until a pass condition is detected.


DTC No. DTC Detection Condition Trouble Area
P0115 Open or short in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
·

Open or short in ECT sensor circuit

·

ECT sensor

·

ECM


P0117 Short in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
·

Short in ECT sensor circuit

·

ECT sensor

·

ECM


P0118 Open in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
·

Open in ECT sensor circuit

·

ECT sensor

·

ECM



HINT:

When any of these DTCs are set, check the ECT by selecting the following menu items on the GTS: Powertrain / Engine and ECT / Data List / Coolant Temp.


Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit

WIRING DIAGRAM

A112566E35
0.243,0.3 2.532,0.481 2.288,0.181 10 Engine Coolant Temperature Sensor 0.243,0.131 0.469,0.313 0.226,0.181 10 D7 6.1,0.11 6.425,0.292 0.326,0.181 10 ECM 5.82,0.11 6.027,0.292 0.208,0.181 10 D2 6.244,0.507 6.469,0.688 0.225,0.181 10 5 V 5.545,0.916 5.944,1.097 0.399,0.181 10 THW 5.545,1.524 5.995,1.706 0.450,0.181 10 ETHW 6.132,0.829 6.288,1.011 0.156,0.181 10 R 2.002,0.944 2.335,1.125 0.333,0.181 10 THW 2.1,1.567 2.287,1.749 0.187,0.181 10 E2 5.275,0.916 5.448,1.097 0.173,0.181 10 97 5.275,1.524 5.448,1.706 0.173,0.181 10 96 2.436,0.916 2.533,1.097 0.096,0.181 10 2 2.436,1.524 2.533,1.706 0.096,0.181 10 1

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


d.

Read the value displayed on the GTS.

OK:

Between 80°C and 100°C (176°F and 212°F) with warm engine.


Result
Temperature Displayed Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
Between 80°C and 100°C (176°F and 212°F) C

HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).


·

If there is a short circuit, the GTS indicates 140°C (284°F) or higher.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A394019E01
0.25,2.833 0.667,3.083 0.417,0.25 0.302,0.458 1.26,0.719 0.958,0.26 10 false ECT Sensor 2.438,0.49 3.042,0.75 0.604,0.26 10 false ECM 2.5,1.333 3.104,1.594 0.604,0.26 10 false THW 2.458,1.792 3.063,2.052 0.604,0.26 10 false ETHW 0.302,2.208 2.115,2.51 1.813,0.302 10 false Wire Harness Side 0.365,2.875 0.969,3.135 0.604,0.26 10 false D7 0.823,2.854 2.406,3.177 1.583,0.323 10 false ECT Sensor Connector 1.344,4.24 2.385,4.438 1.042,0.198 10 false Front View

Disconnect the Engine Coolant Temperature (ECT) sensor connector.


b.

Connect terminals THW and E2 of the ECT sensor connector on the wire harness side.


c.

Connect an GTS to the DLC3.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


f.

Read the value displayed on the GTS.

Standard:

140°C (284°F) or higher.




NG

3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

OK

3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the ECT sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D7-2 (THW) - D2-97 (THW) Always Below 1 Ω
D7-1 (E2) - D2-96 (ETHW) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A395375E02
0.417,0.323 1.167,0.49 0.75,0.167 10 false ECT Sensor 2.531,0.219 2.885,0.406 0.354,0.188 10 false ECM 2.542,1.052 2.865,1.25 0.323,0.198 10 false THA 2.521,1.521 2.938,1.719 0.417,0.198 10 false ETHA

Disconnect the ECT sensor connector.


b.

Connect an GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


e.

Read the value displayed on the GTS.

Standard:

-40°C (-40°F)




NG

5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

OK

5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the ECT sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D7-2 (THW) or D2-97 (THW) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR