Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the intelligent tester, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.



DTC No. DTC Detection Condition Trouble Area
P0504 Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic):
(a) Engine switch on (IG)
(b) STP signal off when ST1- signal off
·

Open or short in stop light switch signal circuit

·

Stop light switch

·

ECM



WIRING DIAGRAM

U189890E02
6.156,4.458 6.823,4.833 0.667,0.375 10 false A7 ECM 6.115,1.635 6.635,1.844 0.521,0.208 10 false ST1- 6.125,0.885 6.604,1.073 0.479,0.188 10 false STP 5.802,0.74 5.979,0.917 0.177,0.177 10 false 36 5.802,1.479 5.979,1.688 0.177,0.208 10 false 35 4.698,1.448 4.875,1.646 0.177,0.198 10 false 3 4.698,0.677 4.865,0.865 0.167,0.188 10 false 1 3.188,1.542 3.365,1.729 0.177,0.188 10 false 4 3.208,0.75 3.365,0.969 0.156,0.219 10 false 2 3.344,2.219 4.823,2.479 1.479,0.26 10 false A33 Stop Light Switch 2.427,1.823 2.719,2.094 0.292,0.271 10 false IGN 2.375,1.052 2.844,1.26 0.469,0.208 10 false STOP 1.823,2.74 3.427,2.896 1.604,0.156 10 false from IG2 Relay 1.708,3.542 3.073,3.719 1.365,0.177 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Stop light switch conditions can be checked using the intelligent tester.

(a)

Connect the intelligent tester to the DLC3.

(b)

Turn the engine switch on (IG).

(c)

Turn the tester on.

(d)

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Stop Light Switch and ST1.

(e)

Check the Data List indication when the brake pedal is depressed and released.

Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF




PROCEDURE

1.CHECK STOP LIGHT SWITCH (TERMINAL VOLTAGE)
a.
U188469E02
0.292,0.094 2.635,0.438 2.344,0.344 10 false Front view of wire harness connector: (to Stop Light Switch) 0.719,2.219 0.99,2.396 0.271,0.177 10 false A33

Disconnect the stop light switch connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A33-2 - Body ground Always 11 to 14 V
A33-4 - Body ground Engine switch on (IG) 11 to 14 V




OK

2.INSPECT STOP LIGHT SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT STOP LIGHT SWITCH
a.

Inspect the stop light switch (See page Vehicle Interior>LIGHTING>STOP LIGHT SWITCH>INSPECTION).



OK

3.CHECK ECM (STP AND ST1- VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH

3.CHECK ECM (STP AND ST1- VOLTAGE)
a.
U188273E02
1.865,3.656 2.75,3.479 true 1.771,3.667 0.542,3.771 true 1.781,0.063 2.552,0.406 0.771,0.344 10 false Brake Pedal Released 0.229,0.063 1,0.385 0.771,0.323 10 false Brake Pedal Depressed 0.073,2.104 1.302,2.281 1.229,0.177 10 false Wire Harness Side 1.167,2.552 2.177,2.729 1.01,0.177 10 false ECM Connector 2.813,3.385 3.104,3.563 0.292,0.177 10 false STP 0.146,3.688 0.469,3.865 0.323,0.177 10 false ST1- 1.375,4.156 2.052,4.333 0.677,0.177 10 false Front View 0.417,2.719 0.625,2.896 0.208,0.177 10 false A7

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Operation Specified Condition
A7-35 (ST1-) - Body ground Released 7.5 to 14 V
Depressed 0 to 3 V
A7-36 (STP) - Body ground Released 0 to 3 V
Depressed 7.5 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH - ECM)