Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P2120  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

HINT:
·

This Electronic Throttle Control System (ETCS) does not use a throttle cable.

·

These DTCs relate to the accelerator pedal position sensor.



The Accelerator Pedal Position (APP) sensor is built into the accelerator pedal sensor assembly and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type sensor and uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0.5 V and 4.75 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the accelerator pedal position sensor itself.

The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.

A112620E02
0.74,1.392 1.554,1.669 0.813,0.276 10 APP Sensor 1.263,1.669 1.744,1.850 0.480,0.181 10 Magnet 0.339,1.842 0.865,2.023 0.526,0.181 10 IC No. 1 0.311,3.318 0.837,3.499 0.526,0.181 10 IC No. 2 2.067,1.739 2.362,1.921 0.295,0.181 10 VPA 2.067,2.071 2.362,2.252 0.295,0.181 10 EPA 2.067,2.393 2.462,2.574 0.395,0.181 10 VCPA 2.067,2.687 2.439,2.869 0.372,0.181 10 VPA2 2.067,3.005 2.439,3.186 0.372,0.181 10 EPA2 2.067,3.327 2.447,3.508 0.380,0.181 10 VCP2 2.693,1.392 3.018,1.574 0.326,0.181 10 ECM 4.267,1.548 4.423,1.729 0.156,0.181 10 *1 5.864,1.548 6.020,1.729 0.156,0.181 10 *2 3.938,1.842 4.225,2.023 0.287,0.181 10 4.55 3.86,2.047 4.225,2.229 0.365,0.181 10 3.988 3.938,2.253 4.225,2.434 0.287,0.181 10 3.75 3.86,2.458 4.225,2.640 0.365,0.181 10 3.188 3.991,2.823 4.201,3.004 0.210,0.181 10 1.6 3.991,3.042 4.201,3.223 0.210,0.181 10 0.8 4.411,3.346 4.698,3.527 0.287,0.181 10 0.29 4.259,3.596 4.414,3.777 0.156,0.181 10 0 5.784,3.596 6.071,3.777 0.287,0.181 10 15.9 4.682,3.587 5.606,3.827 0.924,0.239 10 Usable Range 4.369,4.054 6.867,4.257 2.498,0.202 10 Accelerator Pedal Turning Angle (°) 4.369,4.363 6.648,4.544 2.279,0.181 10 *1: Accelerator Pedal Fully Released 4.369,4.671 6.756,4.836 2.387,0.165 10 *2: Accelerator Pedal Fully Depressed 4.355,2.014 4.234,1.93 false 4.346,2.182 4.234,2.126 false 4.346,2.228 4.234,2.322 false 4.346,2.397 4.234,2.518 false 4.346,2.901 4.215,2.901 false 4.355,3.116 4.206,3.116 false 0.866,3.491 1.347,3.672 0.480,0.181 10 Magnet 0.843,2.878 0.554,3.289 false 0.965,3.195 1.049,3.475 false 0.927,2.504 0.862,1.934 false 1.067,2.205 1.245,1.729 false 1.871,0.851 3.925,1.127 2.054,0.276 10 APP Sensor Output Voltage (V) 4.355,1.841 3.869,0.944 false

DTC No. DTC Detection Condition Trouble Area
P2120 VPA fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic)
·

Accelerator Pedal Position (APP) sensor

·

ECM


P2122 VPA 0.4 V or less for 0.5 seconds or more when accelerator pedal depressed (1 trip detection logic)
·

APP sensor

·

Open in VCPA circuit

·

Open or ground short in VPA circuit

·

ECM


P2123 VPA 4.8 V or more for 2.0 seconds or more
(1 trip detection logic)
·

APP sensor

·

Open in EPA circuit

·

ECM


P2125 VPA2 fluctuates rapidly beyond upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic)
·

APP sensor

·

ECM


P2127 VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal depressed (1 trip detection logic)
·

APP sensor

·

Open in VCP2 circuit

·

Open or ground short in VPA2 circuit

·

ECM


P2128 Conditions (a) and (b) continue for 2.0 seconds or more (1 trip detection logic):
(a) VPA2 4.8 V or more
(b) VPA between 0.4 V and 3.45 V
·

APP sensor

·

Open in EPA2 circuit

·

ECM


P2138 Condition (a) or (b) continues for 2.0 seconds or more (1 trip detection logic):
(a) Difference between VPA and VPA2 0.02 V or less
(b) VPA 0.4 V or less and VPA2 1.2 V or less
·

Short between VPA and VPA2 circuits

·

APP sensor

·

ECM



HINT:

When any of these DTCs are output, check the accelerator pedal position sensor voltage using the GTS. Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.

Trouble Area Accelerator Pedal Fully Released Accelerator Pedal Fully Depressed
Accel Sensor Out No. 1 Accel Sensor Out No. 2 Accel Sensor Out No. 1 Accel Sensor Out No. 2
Open in VCP circuit 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V
Open or ground short in VPA circuit 0 to 0.2 V 1.2 to 2.0 V 0 to 0.2 V 3.4 to 4.75 V
Open or ground short in VPA2 circuit 0.5 to 1.1 V 0 to 0.2 V 2.6 to 4.5 V 0 to 0.2 V
Open in EPA circuit 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V
Normal condition 0.5 to 1.1 V 1.2 to 2.0 V 2.6 to 4.5 V 3.4 to 4.75 V


HINT:

Accelerator pedal positions are expressed as voltages.


FAIL-SAFE

When DTC P2120, P2121, P2122, P2123, P2125, P2127, P2128 or P2138 is stored, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM uses the remaining circuit to calculate the accelerator pedal position to allow the vehicle to continue driving. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.

Fail-safe mode continues until a pass condition is detected, and the engine switch is turned off.

WIRING DIAGRAM

A112573E52
0.219,0.135 0.51,0.333 0.292,0.198 10 false A3 0.219,0.302 2.469,0.5 2.25,0.198 10 false Accelerator Pedal Sensor Assembly 1.594,0.927 1.917,1.135 0.323,0.208 10 false VPA 1.583,1.344 1.917,1.552 0.333,0.208 10 false EPA 1.49,1.76 1.917,1.969 0.427,0.208 10 false VCPA 1.49,2.177 1.927,2.385 0.438,0.208 10 false VPA2 1.5,2.604 1.906,2.813 0.406,0.208 10 false EPA2 1.49,3.021 1.927,3.229 0.438,0.208 10 false VCP2 5.604,0.823 6.073,1.031 0.469,0.208 10 false VPA 5.604,1.469 6.073,1.677 0.469,0.208 10 false EPA 5.594,1.688 6.177,1.896 0.583,0.208 10 false VCPA 5.604,2.063 6.188,2.271 0.583,0.208 10 false VPA2 5.583,2.719 6.167,2.927 0.583,0.208 10 false EPA2 5.604,2.927 6.188,3.135 0.583,0.208 10 false VCP2 6.063,0.344 6.417,0.542 0.354,0.198 10 false ECM 1.99,0.813 2.104,0.958 0.115,0.146 10 false 6 1.99,1.24 2.104,1.385 0.115,0.146 10 false 5 1.99,1.656 2.104,1.802 0.115,0.146 10 false 4 1.99,2.073 2.104,2.219 0.115,0.146 10 false 3 1.99,2.5 2.104,2.646 0.115,0.146 10 false 2 1.99,2.917 2.104,3.063 0.115,0.146 10 false 1 5.323,0.823 5.594,0.979 0.271,0.156 10 false 55 5.323,1.25 5.594,1.406 0.271,0.156 10 false 59 5.323,1.667 5.594,1.823 0.271,0.156 10 false 57 5.323,2.083 5.594,2.24 0.271,0.156 10 false 56 5.323,2.51 5.594,2.667 0.271,0.156 10 false 60 5.323,2.927 5.594,3.083 0.271,0.156 10 false 58 5.771,0.354 6.083,0.521 0.313,0.167 10 false A7

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ACCEL SENSOR OUT NO. 1 AND NO.2)
a.
A208621E09
2.438,1.76 3.146,1.99 0.708,0.229 10 false Released 0.531,1.771 1.333,2 0.802,0.229 10 false Depressed

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.


e.

Read the value displayed on the GTS.

Standard Voltage:
Accelerator Pedal Operation Accel Sensor Out No. 1 Accel Sensor Out No. 2
Fully Released 0.5 to 1.1 V 1.2 to 2.0 V
Fully Depressed 2.6 to 4.5 V 3.4 to 4.75 V




NG

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

OK

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
a.

Disconnect the Accelerator Pedal Position (APP) sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A3-6 (VPA) - A7-55 (VPA) Always Below 1 Ω
A3-5 (EPA) - A7-59 (EPA) Always Below 1 Ω
A3-4 (VCPA) - A7-57 (VCPA) Always Below 1 Ω
A3-3 (VPA2) - A7-56 (VPA2) Always Below 1 Ω
A3-2 (EPA2) - A7-60 (EPA2) Always Below 1 Ω
A3-1 (VCP2) - A7-58 (VCP2) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A3-6 (VPA) or A7-55 (VPA) - Body ground Always 10 kΩ or higher
A3-5 (EPA) or A7-59 (EPA) - Body ground Always 10 kΩ or higher
A3-4 (VCPA) or A7-57 (VCPA) - Body ground Always 10 kΩ or higher
A3-3 (VPA2) or A7-56 (VPA2) - Body ground Always 10 kΩ or higher
A3-2 (EPA2) or A7-60 (EPA2) - Body ground Always 10 kΩ or higher
A3-1 (VCP2) or A7-58 (VCP2) - Body ground Always 10 kΩ or higher




OK

3.INSPECT ECM (VCPA AND VCP2 VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VCPA AND VCP2 VOLTAGE)
U188282E01
0.056,0.03 1.281,0.197 1.224,0.167 10 Wire Harness Side 0.914,0.543 2.614,0.902 1.700,0.359 10 Accelerator Pedal Position Sensor Connector 0.438,0.641 0.703,0.822 0.264,0.181 10 A3 1.778,2.518 2.178,2.686 0.400,0.167 10 VCPA 1.281,2.857 2.014,3.024 0.733,0.167 10 Front View 0.474,2.518 0.874,2.686 0.400,0.167 10 VCP2 2.427,2.518 2.749,2.686 0.323,0.167 10 EPA 1.134,2.518 1.544,2.686 0.409,0.167 10 EPA2 0.717,2.479 1.304,1.83 false 1.355,2.484 1.462,1.858 false 1.981,2.484 1.733,1.858 false 2.511,2.473 1.896,1.858 false

a.

Disconnect the APP sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
A3-4 (VCPA) - A3-5 (EPA) Engine switch on (IG) 4.5 to 5.5 V
A3-1 (VCP2) - A3-2 (EPA2) Engine switch on (IG) 4.5 to 5.5 V




OK

4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

NG

4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL).



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the GTS on.


h.

Fully depress and release the accelerator pedal.


i.

Check that 5 seconds or more have elapsed since the engine switch is turned on (IG).


j.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


k.

Read the DTCs.

Result
Result Proceed to
DTC P2120, P2122, P2123, P2125, P2127, P2128 and/or P2138 are output A
DTC is not output B



A

B

END