Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0010  Camshaft Position "A" Actuator Circuit (Bank 1)  


DESCRIPTION

The Variable Valve Timing (VVT) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing.

The camshaft timing oil control valve is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A395301E01
2.552,4.573 2.969,4.156 false 2.979,4.156 3.281,4.156 false 3.156,4.802 3.313,5.073 false 3.313,5.073 3.594,5.073 false 0.094,0.094 0.948,0.281 0.854,0.188 10 false VVT System: 0.229,2.833 0.958,3.021 0.729,0.188 10 false Duty-cycle 4.75,0.833 6.396,1.042 1.646,0.208 10 false Camshaft Position Sensor 4.771,1.344 6.49,1.563 1.719,0.219 10 false Crankshaft Position Sensor 4.979,1.854 6.302,2.052 1.323,0.198 10 false Mass Air Flow Meter 4.906,2.354 6.448,2.542 1.542,0.188 10 false Throttle Position Sensor 4.51,2.875 6.781,3.083 2.271,0.208 10 false Engine Coolant Temperature Sensor 5,3.375 6.427,3.583 1.427,0.208 10 false Vehicle Speed Sensor 2.365,1.229 3.635,1.417 1.271,0.188 10 false Actual Valve Timing 2.375,1.958 3.615,2.167 1.24,0.208 10 false Target Valve Timing 2.688,2.667 3.354,2.875 0.667,0.208 10 false Correction 2.844,3.177 3.188,3.365 0.344,0.188 10 false ECM 1.573,3.76 3.688,3.969 2.115,0.208 10 false Camshaft Timing Oil Control Valve 0.375,4.26 1.708,4.448 1.333,0.188 10 false Engine Oil Pressure 3.344,4.083 6.417,4.292 3.073,0.208 10 false VVT Controller (Camshaft Timing Gear Assembly) 3.635,4.99 4.698,5.188 1.063,0.198 10 false Intake Camshaft

DTC No. DTC Detection Condition Trouble Area
P0010 Open or short in camshaft timing oil control valve circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve circuit

·

Camshaft timing oil control valve

·

ECM



WIRING DIAGRAM

A133814E18
0.135,2.118 2.336,2.314 2.201,0.196 10 Camshaft Timing Oil Control Valve 0.135,1.964 0.447,2.118 0.312,0.154 10 D53 5.453,0.855 5.837,1.036 0.384,0.181 10 OC1+ 5.453,1.767 5.802,1.948 0.349,0.181 10 OC1- 5.082,0.855 5.375,1.036 0.293,0.181 10 100 5.642,2.417 5.873,2.598 0.231,0.181 10 D2 5.082,1.556 5.361,1.738 0.279,0.181 10 123 1.502,0.855 1.663,1.036 0.161,0.181 10 1 1.502,1.556 1.656,1.738 0.154,0.181 10 2 5.948,2.417 6.379,2.606 0.431,0.188 10 ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTC after recording the freeze frame data and DTC (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).


e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG) and wait 5 seconds.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the DTCs.

Result
Result Proceed to
DTC P0010 is output A
DTC is not output B



A

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE

B

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE
a.

Inspect the camshaft timing oil control valve (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - ECM)
a.

Disconnect the camshaft timing oil control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (check for open):
Tester Connection Condition Specified Condition
D53-1 - D2-100 (OC1+) Always Below 1 Ω
D53-2 - D2-123 (OC1-) Always Below 1 Ω


Standard Resistance (check for short):
Tester Connection Condition Specified Condition
D53-1 or D2-100 (OC1+) - Body ground Always 10 kΩ or higher
D53-2 or D2-123 (OC1-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR