Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM D

2AZ-FE ENGINE CONTROL  SFI SYSTEM  DIAGNOSIS SYSTEM  


EURO-OBD (EUROPEAN SPEC.)


A208456

When troubleshooting Europe On-Board Diagnostic (Euro-OBD) vehicles, the vehicle must be connected to an OBD scan tool (complying with ISO 15765-4). Various data output from the vehicle's ECM can then be read.

Euro-OBD regulations require that the vehicle's on-board computer illuminate the Malfunction Indicator Lamp (MIL) on the instrument panel when the computer detects a malfunction in:

a.

The emission control system components


b.

The powertrain control components (which affect vehicle emissions)


c.

The computer

In addition, if the applicable Diagnostic Trouble Codes (DTCs) prescribed by ISO 15765-4 are recorded in the ECM memory. If the malfunction does not reoccur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the ECM memory.

To check DTCs, connect the GTS or OBD scan tool to the Data Link Connector3 (DLC3) of the vehicle.

The scan tool displays DTCs, the freeze frame data and a variety of engine data.

The DTCs and freeze frame data can be erased the scan tool (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).



M-OBD (EXCEPT EUROPEAN SPEC.)


A208456

When troubleshooting Multiplex On-Board Diagnostic (M-OBD) vehicle, the vehicle must be connected to the GTS. Various data output from the ECM can then be read.

OBD regulations require that the vehicle's on-board computer illuminate the MIL on the instrument panel when the computer detects a malfunction in:

a.

The emission control system/components


b.

The powertrain control components (which affect vehicle emissions)


c.

The computer

In addition, the applicable DTCs are recorded in the ECM memory. If the malfunction does not recur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the ECM memory.



NORMAL MODE AND CHECK MODE


The diagnosis system operates in "normal mode" during normal vehicle use. In normal mode, "2 trip detection logic" is used to ensure accurate detection of malfunctions. "Check mode" is also available to technicians as an option. In check mode, "1 trip detection logic" is used for simulating malfunction symptoms and increasing the system's ability to detect malfunctions, including intermittent malfunctions (GTS only).


2-TRIP DETECTION LOGIC


When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected again after the engine switch is turned off and then on (IG), the MIL illuminated.


DLC3 (Data Link Connector 3)




INSPECT BATTERY VOLTAGE


Battery Voltage:

11 to 14 V


If the voltage is below 11 V, replace the battery before proceeding to the next step.


CHECK MIL


a.

Check that the MIL illuminates when the engine switch is turned on (IG).

If the MIL does not illuminate, there is a problem in the MIL circuit (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>MIL Circuit).


b.

When the engine is started, the MIL should turn off.



ALL READINESS


HINT:
·

With "All Readiness", you can check whether or not the DTC judgment has been completed by using the GTS.

·

You should check "All Readiness" after duplicating malfunction symptoms or for validation after finishing repairs.



a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.


e.

Turn the engine switch off and wait for 30 seconds.


f.

Turn the engine switch on (IG) and turn the GTS on.


g.

Perform the DTC judgment driving pattern to run the DTC judgment.


h.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


i.

Input the DTCs to be confirmed.


j.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

You should perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit