Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM J

2AZ-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunction detected by the ECM. When the engine switch is turned on (IG), power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually: When the engine switch is turned on (IG), the MIL should be illuminated and should then turn off after engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A194440E07
1.281,1.26 2.333,1.521 1.052,0.26 10 false Main Body ECU 0.302,1.854 1.01,2.167 0.708,0.313 10 false AM2 No. 2 0.938,0.385 1.271,0.604 0.333,0.219 10 false G57 0.948,0.854 1.26,1.094 0.313,0.24 10 false G58 2.375,0.375 2.719,0.646 0.344,0.271 10 false G58 1.271,0.375 1.583,0.552 0.313,0.177 10 false AM1 1.271,0.844 1.583,1.021 0.313,0.177 10 false AM2 1.969,0.375 2.333,0.552 0.365,0.177 10 false IG2D 1.021,0.198 1.135,0.365 0.115,0.167 10 false 6 1.021,0.677 1.135,0.844 0.115,0.167 10 false 1 2.438,0.198 2.625,0.365 0.188,0.167 10 false 11 3.198,2.5 3.542,2.667 0.344,0.167 10 false MET 1.969,3.063 2.219,3.229 0.25,0.167 10 false IG2 1.656,2.271 1.771,2.438 0.115,0.167 10 false 5 1.656,2.677 1.771,2.844 0.115,0.167 10 false 2 2.396,2.271 2.51,2.438 0.115,0.167 10 false 3 2.396,2.677 2.51,2.844 0.115,0.167 10 false 1 0.656,2.833 0.906,3 0.25,0.167 10 false IG2 0.698,3.74 1.344,4.052 0.646,0.313 10 false F/B BATT 0.698,4.302 1.344,4.615 0.646,0.313 10 false FL MAIN 0.802,4.938 1.292,5.115 0.49,0.177 10 false Battery 3.49,2.792 3.781,2.969 0.292,0.177 10 false G28 3.49,2.979 5.344,3.25 1.854,0.271 10 false Combination Meter Assembly 3.635,2.281 3.854,2.458 0.219,0.177 10 false 21 5.01,2.271 5.25,2.427 0.24,0.156 10 false 25 3.854,2.5 4.104,2.667 0.25,0.167 10 false IG2 4.74,2.5 4.99,2.667 0.25,0.167 10 false EFI 5.719,2.281 5.885,2.427 0.167,0.146 10 false W 5.5,2.271 5.688,2.427 0.188,0.156 10 false 24 6.135,5.344 6.469,5.49 0.333,0.146 10 false ECM 5.885,5.344 6.125,5.49 0.24,0.146 10 false A7

PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Condition Proceed to
MIL remains ON A
MIL does not illuminate B



A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER MIL TURNS OFF
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Check if any DTCs have been stored. Note down any DTCs.



f.

Check if the MIL goes off.

Standard:

MIL should go off.




NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

OK

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the A7 ECM connector.


b.

Turn the engine switch on (IG).


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.




NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)

OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
a.

Disconnect the combination meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A7-24 (W) or G28-25 (EFI) - Body ground Always 10 kΩ or higher




NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

REPLACE COMBINATION METER ASSEMBLY

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the engine switch is turned on (IG).

OK:

MIL should be illuminated.




NG

6.CHECK THAT ENGINE STARTS

OK

6.CHECK THAT ENGINE STARTS
a.

Start the engine.

Result Proceed to
Engine starts A
Engine does not start* B

HINT:

*: The GTS cannot communicate with the ECM.




A

7.INSPECT COMBINATION METER ASSEMBLY (MIL CIRCUIT)

B

7.INSPECT COMBINATION METER ASSEMBLY (MIL CIRCUIT)

OK

CHECK AND REPLACE HARNESS OR CONNECTOR (COMBINATION METER - ECM)

NG

REPLACE COMBINATION METER ASSEMBLY