Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P2237  Oxygen (A/F) Sensor Pumping Current Circuit / Open (for A/F sensor) (Bank 1 Sensor 1)  P2238  Oxygen Sensor Pumping Current Circuit Low (for A/F sensor) (Bank 1 Sensor 1)  P2239  Oxygen Sensor Pumping Current Circuit High (for A/F sensor) (Bank 1 Sensor 1)  P2252  Oxygen Sensor Reference Ground Circuit Low (for A/F sensor) (Bank 1 Sensor 1)  P2253  Oxygen Sensor Reference Ground Circuit High (for A/F sensor) (Bank 1 Sensor 1)  


DESCRIPTION

Refer to DTC P0031 (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>P0031).

DTC No. DTC Detection Condition Trouble Area
P2237 An open or short in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while the engine is running (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


P2238
·

Case 1:

Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic):

(a)

Voltage at terminal A1A+ is 0.5 V or less.

(b)

Voltage difference between terminals A1A+ and A1A- is 0.1 V or less.


·

Case 2:

Air fuel ratio sensor admittance is less than 0.015 1/Ω (2 trip detection logic).


·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


P2239 The A1A+ voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


P2252 The A1A- voltage is 0.5 V or less (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


P2253 The A1A- voltage is higher than 4.5 V (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM



MONITOR DESCRIPTION

These DTCs are output when there is an open or short in the air fuel ratio sensor circuit, or if the air fuel ratio sensor output drops. To detect these problems, the voltage of the air fuel ratio sensor is monitored when turning the engine switch on (IG), and the admittance (admittance is an electrical term that indicates the ease of flow of current) is checked while driving. If the voltage of the air fuel ratio sensor is higher than 0.5 V, or 4.5 V or less, it is considered normal. If the voltage is out of the specified range, or the admittance is less than the standard value, the ECM determines that there is a malfunction in the air fuel ratio sensor. If the same malfunction is detected in next driving cycle, the MIL is illuminated and a DTC is stored.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Refer to "Data List / Active Test" [AFS Voltage B1S1] (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D56-1 (HA1A) - D2-109 (HA1A) Always Below 1 Ω
D56-3 (A1A+) - D2-112 (A1A+) Always Below 1 Ω
D56-4 (A1A-) - D2-113 (A1A-) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D56-1 (HA1A) or D2-109 (HA1A) - Body ground Always 10 kΩ or higher
D56-3 (A1A+) or D2-112 (A1A+) - Body ground Always 10 kΩ or higher
D56-4 (A1A-) or D2-113 (A1A-) - Body ground Always 10 kΩ or higher




OK

2.REPLACE AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE AIR FUEL RATIO SENSOR
a.


NEXT

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2237, P2238, P2239, P2252 OR P2253)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2237, P2238, P2239, P2252 OR P2253)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the GTS on.


h.

Start the engine and wait 5 minutes or more.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


j.

Input the DTC: P2237, P2238, P2239, P2252 or P2253.


k.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL
(DTC is not output)
A
ABNORMAL
(DTC P2237, P2238, P2239, P2252 or P2253 is output)
B



A

END

B