Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0100  Mass Air Flow Circuit  P0102  Mass Air Flow Circuit Low  P0103  Mass Air Flow Circuit High  


DESCRIPTION

The Mass Air Flow (MAF) meter is a sensor that measures the amount of air flowing through the throttle valve. The ECM uses this information to determine fuel injection duration and to provide an appropriate air fuel ratio.

Inside the mass air flow meter, there is a heated platinum wire which is exposed to the flow of intake air. By applying a specific electrical current to the wire, the ECM heats it to a specific temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.

The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:

When any of these DTCs is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A165052E36
1.906,1.49 1.573,0.323 1.573,0.323 1.427,0.323 false 2.271,1.49 2.406,1.063 2.406,1.063 2.563,1.063 false 4.823,1.333 4.396,1.917 4.396,1.917 4.396,2.188 false 5.115,1.563 5.563,1.906 5.563,1.906 5.563,2.167 false 5.115,2.198 7.156,2.438 2.042,0.24 10 false Temperature Sensor (Thermistor) 2.25,0.198 2.531,0.417 0.281,0.219 10 false +B 2.24,0.552 3.604,0.792 1.365,0.24 10 false Power Transistor 3.313,2.208 5.417,2.406 2.104,0.198 10 false Platinum Hot Wire (Heater) 1.656,1.49 1.823,1.698 0.167,0.208 10 false A 2.469,1.479 2.656,1.677 0.188,0.198 10 false B 2.885,1.583 4.083,1.781 1.198,0.198 10 false Output Voltage 2.604,0.979 4.406,1.177 1.802,0.198 10 false Platinum Hot Wire (Heater) 0.177,0.24 1.469,0.615 1.292,0.375 10 false Temperature Sensor (Thermistor)

DTC No. DTC Detection Condition Trouble Area
P0100 MAF meter voltage is less than the specified value, or more than the specified value for 3 seconds or more
(1 trip detection logic)
·

Open or short in MAF meter circuit

·

MAF meter

·

ECM


P0102 MAF meter voltage is less than the specified value for 3 seconds or more
(1 trip detection logic)
·

Open or short in MAF meter circuit

·

MAF meter

·

ECM


P0103 MAF meter voltage is more than the specified value for 3 seconds or more
(1 trip detection logic)
·

Open or short in MAF meter circuit

·

MAF meter

·

ECM



HINT:

When any of these DTCs are set, check the air-flow rate by selecting the following menu items on the GTS: Powertrain / Engine and ECT / Data List / MAF.

Mass Air Flow Rate (gm/sec.) Malfunction
Approximately 0.0
·

Open in MAF meter power source circuit

·

Open or short in VG circuit


271.0 or more
·

Open in E2G circuit




WIRING DIAGRAM

A235531E01
0.708,2.028 1.342,2.219 0.634,0.191 10 FL MAIN 0.818,2.805 1.339,3.006 0.520,0.202 10 Battery 1.086,0.617 1.381,0.809 0.295,0.191 10 EFI 2.02,0.393 2.680,0.585 0.660,0.191 10 EFI MAIN 0.708,1.355 1.419,1.547 0.711,0.191 10 F/B BATT 3.638,0.779 3.870,0.951 0.232,0.172 10 +B 3.456,0.779 3.570,0.951 0.114,0.172 10 3 2.626,0.779 2.740,0.951 0.114,0.172 10 3 1.876,0.779 1.990,0.951 0.114,0.172 10 5 2.626,1.122 2.740,1.294 0.114,0.172 10 1 1.876,1.122 1.990,1.294 0.114,0.172 10 2 4.846,1.087 4.961,1.259 0.114,0.172 10 5 4.846,1.581 4.961,1.753 0.114,0.172 10 4 3.575,2.235 4.926,2.409 1.350,0.174 10 Mass Air Flow Meter 4.561,1.109 4.809,1.268 0.247,0.159 10 VG 4.493,1.623 4.833,1.782 0.340,0.159 10 E2G 5.749,1.095 6.069,1.254 0.320,0.159 10 VG 5.436,1.011 5.756,1.170 0.320,0.159 10 118 5.45,1.193 5.656,1.352 0.206,0.159 10 D2 5.436,1.509 5.756,1.667 0.320,0.159 10 116 5.45,1.691 5.656,1.849 0.206,0.159 10 D2 5.464,2.795 5.657,2.954 0.193,0.159 10 44 3.575,2.063 3.810,2.222 0.235,0.159 10 D3 5.464,2.977 5.670,3.136 0.206,0.159 10 A7 5.749,1.609 6.115,1.768 0.367,0.159 10 E2G 5.749,2.885 6.217,3.044 0.468,0.159 10 MREL 6.154,0.367 6.542,0.532 0.387,0.165 10 ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result
Result Proceed to
DTC P0102 is output (P0100 and P0102 are output) A
DTC P0103 is output (P0100 and P0103 are output) B



A

2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)

B

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)
a.
U188313E02
0.906,0.635 1.698,1.042 false 0.083,0.063 1.292,0.26 1.208,0.198 10 false Wire Harness Side 1.115,1.635 2.521,1.833 1.406,0.198 10 false MAF Meter Connector 0.396,0.51 0.844,0.708 0.448,0.198 10 false +B (+) 0.698,1.646 0.927,1.823 0.229,0.177 10 false D3 2.417,0.188 3.146,0.365 0.729,0.177 10 false Front View

Disconnect the Mass Air Flow (MAF) meter connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D3-3 (+B) - Body ground Engine switch on (IG) 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI MAIN RELAY - MAF METER)

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the MAF meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D3-5 (VG) - D2-118 (VG) Always Below 1 Ω
D3-4 (E2G) - D2-116 (E2G) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D3-5 (VG) or D2-118 (VG) - Body ground Always 10 kΩ or higher




OK

4.INSPECT MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MASS AIR FLOW METER
a.

Inspect the mass air flow meter, referring to the On-vehicle Inspection for Mass Air Flow Meter (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>MASS AIR FLOW METER>ON-VEHICLE INSPECTION).


b.

Inspect the function of the mass air flow meter.

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.


v.

Start the engine.


vi.

Check that the MAF value changes when the engine is raced.

OK:

The reading changes.





OK

NG

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.

Disconnect the MAF meter connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D3-4 (E2G) - Body ground Always Below 1 Ω




OK

NG

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the MAF meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D3-4 (E2G) - D2-116 (E2G) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR