Home › Engine / Hybrid System › 2GR-FE FUEL › FUEL INJECTOR
RM24M0E _51 Engine / Hybrid System _059543 2GR-FE FUEL _0291803 FUEL INJECTOR G

2GR-FE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 23250 1.INSPECT FUEL INJECTOR ASSEMBLY

A116182

a.

Inspect the injector resistance.

i.

Using an ohmmeter, measure the resistance between the terminals.

Standard resistance:
Tester Connection Condition Specified Condition
1-2 always 11.6 to 12.4 Ω at 20°C (68°F)


If the resistance is not as specified, replace the injector.



b.

Inspect the injection volume.

CAUTION:

This test involves high-pressure fuel and electricity. Take every precaution regarding the safe handling of both fuel and electricity. Perform this test in a safe area, and avoid any sparks or flames. Do not smoke.


i.
A264971E18
0.51,1.646 0.635,2 0.635,2 0.729,2 false 0.75,0.938 0.938,0.302 0.938,0.302 1.063,0.302 false 2.26,1.771 1.792,1.469 1.792,1.469 1.781,1.26 false 2.802,1.094 2.802,0.844 false 2.292,1.719 2.5,1.906 0.208,0.188 10 false *c 1.177,0.24 2.156,0.406 0.979,0.167 10 false *b 0.833,1.938 1.115,2.083 0.281,0.146 10 false *a 2.74,1.146 3.021,1.323 0.281,0.177 10 false *d

Install the fuel tube connector to SST (hose), then connect the tube connector to the fuel pipe (vehicle side).

Text in Illustration
*a SST (Hose)
*b SST (Hose Band)
*c SST (Fuel Tube Connector)
*d Fuel Pipe (Vehicle Side)

SST
09268-31013  (09268-41500, 90467-13001, 95336-08070)

NOTICE:

Do not scratch or allow any foreign matter on the connection between the fuel tube connector and the pipe, as they are sealed with the SST connector O-ring.



ii.

Install the O-ring to the fuel injector.


iii.
A264972E15
1,0.146 1.333,0.146 false 0.99,1.906 1.323,1.906 false 0.969,0.76 1.302,0.76 false 1.49,1.021 1.708,1.021 false 2.115,1.354 2.448,1.354 false 1.719,0.333 2.052,0.333 false 0.802,0.073 1.042,0.271 0.24,0.198 10 false *a 0.802,0.667 1.042,0.865 0.24,0.198 10 false *c 2.104,0.26 2.344,0.458 0.24,0.198 10 false *b 0.823,1.813 1.063,2.01 0.24,0.198 10 false *e 1.729,0.938 1.969,1.135 0.24,0.198 10 false *1 2.49,1.292 2.729,1.49 0.24,0.198 10 false *d

Connect SST (adaptor and hose) to the injector, and hold the injector and union with SST (clamp).

Text in Illustration
*1 O-ring
*a SST (Hose)
*b SST (Hose Band)
*c SST (Adapter)
*d SST (Clamp)
*e Vinyl Tube

SST
09268-31013  (09268-41141, 09268-41410, 90467-13001, 95336-08070)


iv.

Put the injector into the graduated cylinder.

CAUTION:

Install a suitable vinyl tube onto the injector that will contain gasoline spray.




vi.
A264973E19
2.042,0.542 2.042,0.958 false 1.99,0.99 2.146,1.229 0.156,0.24 10 false *a 1.031,1.354 1.188,1.594 0.156,0.24 10 false *b

Connect SST (wire) to the injector and the battery for 15 seconds, and measure the injection volume with the graduated cylinder. Test each injector 2 or 3 times.

Text in Illustration
*a SST (Wire)
*b Connect

SST
09842-30080  

Volume:

84 to 100 cm3 (5.1 to 6.0 cu in.) in 15 seconds


Difference between each injector:

16 cm3 (0.98 cu in.) or less


If the injection volume is not as specified, replace the injector.



c.
A132391

Check for leaks.

i.

In the condition above, disconnect the tester probes of SST (wire) from the battery and check for fuel leaks from the injector.

Fuel drop:

1 drop or less in 16 minutes