Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › ENGINE UNIT
RM24M0E _51 Engine / Hybrid System _059547 2GR-FE ENGINE MECHANICAL _0291827 ENGINE UNIT A

2GR-FE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Select the No. 1 valve rocker arm sub-assemblies, inner compression springs and valve spring retainers based on the identification mark on the cylinder head.

A333608E03
4.344,0.594 4.479,0.396 4.479,0.396 4.688,0.396 false 4.333,1.906 4.479,1.719 4.479,1.719 4.719,1.719 false 4.448,1.917 4.479,1.729 false 4.26,3.365 4.438,3.146 4.438,3.146 4.656,3.146 false 4.323,4.76 4.469,4.573 4.469,4.573 4.656,4.573 false 4.438,4.76 4.469,4.573 false 4.104,0.271 4.615,0.677 0.51,0.406 12 false *A 4.104,1.615 4.615,2.021 0.51,0.406 12 false *B 4.094,3.031 4.604,3.438 0.51,0.406 12 false *A 4.083,4.469 4.594,4.875 0.51,0.406 12 false *B 0.313,0.156 0.823,0.563 0.51,0.406 12 false *C 0.323,3.031 0.833,3.438 0.51,0.406 12 false *D 4.719,0.292 5.229,0.698 0.51,0.406 10 false *a 4.76,1.625 5.271,2.031 0.51,0.406 10 false *a 4.698,3.052 5.208,3.458 0.51,0.406 10 false *a 4.708,4.469 5.219,4.875 0.51,0.406 10 false *a

Text in Illustration
*A Type A *B Type B
*C Cylinder Head RH *D Cylinder Head LH
*a Identification Mark - -

Type Identification Mark Inner Compression Spring Shape
A 1 Hole Straight
B 2 Holes Taper

·
A336090E02
0.052,0.063 1.698,4.5 1.646,4.438 1.781,0.063 3.385,4.5 1.604,4.438 1.146,2.094 1.146,2.354 false 2.854,2.083 2.854,2.344 false 2.604,2.979 2.885,2.979 false 0.896,3.01 1.167,3.01 false 0.958,3.802 1.229,3.802 false 2.656,3.885 2.927,3.885 false 0.104,0.083 0.5,0.333 0.396,0.25 12 false *A 1.833,0.083 2.229,0.333 0.396,0.25 12 false *B 1.396,0.885 1.667,1.125 0.271,0.24 10 false *b 3.125,0.875 3.344,1.115 0.219,0.24 10 false *b 1.042,2.354 1.313,2.594 0.271,0.24 10 false *1 2.771,2.354 3.042,2.594 0.271,0.24 10 false *1 0.615,2.458 0.885,2.698 0.271,0.24 10 false *a 2.344,2.479 2.615,2.719 0.271,0.24 10 false *a 2.917,2.896 3.188,3.135 0.271,0.24 10 false *2 1.229,2.917 1.5,3.156 0.271,0.24 10 false *2 1.281,3.708 1.552,3.948 0.271,0.24 10 false *3 2.99,3.781 3.26,4.021 0.271,0.24 10 false *3

There are 2 types of No. 1 valve rocker arm sub-assemblies, inner compression springs and valve spring retainers. The 2 types are not interchangeable.

Text in Illustration
*A Type A
*B Type B
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Spring Retainer
*3 Inner Compression Spring
*a Valve Spring Retainer Diameter
*b No. 1 Valve Rocker Arm Sub-assembly Roller Width

Type No. 1 Valve Rocker Arm Sub-assembly Roller Width Valve Spring Retainer Diameter Inner Compression Spring Shape
A 10.7 mm (0.421 in.) 23.4 mm (0.921 in.) Straight
B 8.0 mm (0.315 in.) 18.9 mm (0.744 in.) Taper



PROCEDURE

Hide 15620 1.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.

Remove the oil filler cap sub-assembly and oil filler cap gasket.


Hide 19100P 2.REMOVE SPARK PLUG

a.

Remove the 6 spark plugs.


Hide 12101A 3.REMOVE OIL PAN DRAIN PLUG

a.
A129654

Remove the oil pan drain plug and oil pan drain plug gasket.


Hide 12204 4.REMOVE VENTILATION VALVE SUB-ASSEMBLY

a.
A129655

Remove the ventilation valve sub-assembly.


Hide 5.REMOVE CAMSHAFT POSITION SENSOR

a.
A306456E02
0.12,0.042 0.716,0.223 0.595,0.181 10 Bank 1: 0.135,2.351 0.773,2.532 0.638,0.181 10 Bank 2:

Remove the 4 bolts and 4 camshaft position sensors.


Hide 11101J 6.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

a.
A306457E02
0.163,0.125 0.905,0.307 0.741,0.181 10 Bank 1: 0.163,2.325 0.920,2.507 0.757,0.181 10 Bank 2:

Remove the 4 bolts and 4 camshaft timing oil control valve assemblies.


Hide 11401G 7.REMOVE CRANKSHAFT POSITION SENSOR

a.
A129663

Remove the bolt and crankshaft position sensor.


Hide 15771 8.REMOVE NO. 1 OIL PIPE

a.
A395366E01
0.76,0.896 1.719,1.125 0.958,0.229 10 true Oil Pipe Union 1.885,1.708 2.896,2 1.01,0.292 10 true Oil Pipe Union

Remove the 2 oil pipe unions, 3 gaskets and No. 1 oil pipe.


b.

Remove the oil control valve filter LH.


Hide 15771M 9.REMOVE OIL PIPE

a.
A134878E03
0.906,0.708 1.927,1.052 1.021,0.344 10 true Oil Pipe Union 1.438,1.833 2.458,2.146 1.021,0.313 10 true Oil Pipe Union

Remove the bolt.


b.

Remove the 2 oil pipe unions, 3 gaskets and oil pipe.


c.

Remove the oil control valve filter RH.


Hide 11415 10.REMOVE TAPER SCREW PLUG

HINT:

Perform this operation only when a taper screw plug is installed.


a.
A292824

Remove the taper screw plug from the cylinder block sub-assembly.


Hide 11415 11.REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

a.

for Bank 1:

i.
A305214E01
0.183,0 0.702,0.188 0.519,0.188 10 Bank 1: 0.183,1.682 0.702,1.870 0.519,0.188 10 Bank 2:

Remove the cylinder block water drain cock sub-assembly from the cylinder block sub-assembly.


ii.

Remove the cylinder block water drain cock plug from the cylinder block water drain cock sub-assembly.



b.

for Bank 2:

HINT:

Perform this operation only when a cylinder block water drain cock sub-assembly is installed.


i.

Remove the cylinder block water drain cock sub-assembly from the cylinder block sub-assembly.


ii.

Remove the cylinder block water drain cock plug from the cylinder block water drain cock sub-assembly.



Hide 13471 13.REMOVE CRANKSHAFT PULLEY

a.
U188289E01
2.459,1.771 2.768,1.922 0.309,0.151 10 SST 1.142,2.969 1.450,3.120 0.309,0.151 10 Turn 2.792,2.338 3.100,2.490 0.309,0.151 10 Hold 1.173,1.882 2.414,1.858 2.414,1.858 1.606,2.441 false 1.596,3.118 1.604,3.187 false

Using SST, loosen the crankshaft pulley bolt.

SST
09213-70011  (09213-70020)
09330-00021  


b.
U188290E01
0.68,1.422 0.988,1.573 0.309,0.151 10 SST 2.665,2.824 2.973,2.976 0.309,0.151 10 Turn 0.126,2.113 0.435,2.264 0.309,0.151 10 Hold 1.264,2.078 1.142,1.513 1.142,1.513 1.04,1.513 false 1.309,3.003 1.261,2.949 false

Using SST, remove the crankshaft pulley bolt and crankshaft pulley.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05021)


Hide 12315 14.REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET LH

a.
A160590

Remove the 6 bolts and No. 1 front engine mounting bracket LH.


b.

Using an E8 "TORX" socket wrench, remove the 2 stud bolts.


Hide 16323 15.REMOVE WATER INLET HOUSING

a.
A129673

Remove the 2 nuts, water inlet and thermostat.


b.

Remove the gasket.


c.

Remove the 2 stud bolts.


d.

Slide the clip and disconnect the No. 1 water by-pass hose.


e.
A134879E17
0.885,1.333 1.167,1.729 0.281,0.396 10 true Nut

Remove the drain cock plug.


f.

Remove the drain cock assembly.


g.

Remove the 2 bolts, nut, and water inlet housing.


h.
A129675

Remove the 2 O-rings.


Hide 16331 16.REMOVE WATER OUTLET

a.
A129676E15
0.708,1.521 0.948,1.927 0.24,0.406 10 true Nut 2.625,1.5 2.938,1.875 0.313,0.375 10 true Nut 2.521,0.427 2.823,0.781 0.302,0.354 10 true Nut 0.76,0.427 1.042,0.771 0.281,0.344 10 true Nut

Remove the 2 bolts, 4 nuts and water outlet.


b.
A129677

Remove the 2 gaskets and O-ring.


Hide 11201 17.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 1)

a.
A129679

Remove the 12 bolts, seal washer, cylinder head cover sub-assembly and cylinder head cover gasket.


b.
A129699

Remove the 3 gaskets.


Hide 11202 18.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 2)

a.
A383795E02
2.604,0.927 2.927,1.052 false 1.833,0.823 2.604,1.125 0.771,0.302 10 true Baffle Plate

Remove the 12 bolts, seal washer, cylinder head cover sub-assembly and cylinder head cover gasket.

NOTICE:

The baffle plate is located on the back of the portion shown in the illustration. Do not damage the baffle plate when removing the cylinder head cover sub-assembly.



b.
A129705

Remove the 3 gaskets.


Hide 12102A 19.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

a.
A129680E11
0.271,1.667 0.521,1.833 0.25,0.167 10 false Nut 2.458,0.469 2.74,0.802 0.281,0.333 10 true Nut

Remove the 16 bolts and 2 nuts.


b.
A120816

Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.

NOTICE:

Be careful not to damage the contact surfaces of the oil pans.



c.

Using an E6 "TORX" socket wrench, remove the 2 stud bolts.


Hide 15104 20.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A129681

Remove the bolt, 2 nuts, oil strainer sub-assembly and gasket.


b.

Using an E6 "TORX" socket wrench, remove the 2 stud bolts.


Hide 12101 21.REMOVE OIL PAN SUB-ASSEMBLY

a.
A160594E05
0.188,1.417 0.458,1.573 0.271,0.156 10 false Nut 2.146,2.5 2.438,2.844 0.292,0.344 10 true Nut

Remove the 16 bolts and 2 nuts.

HINT:

Be sure to clean the bolts and stud bolts, and check the threads for cracks or other damage.



b.
A129683E12
0.625,0.677 1.521,0.229 false 0.688,2.792 1.615,3.073 1.615,3.073 2.74,2.521 true 1.573,0.135 2.635,0.448 1.063,0.313 10 false Protective Tape 1.25,3.052 2.26,3.396 1.01,0.344 10 true Protective Tape

Remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block sub-assembly with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and oil pan sub-assembly.


HINT:

Tape the screwdriver tip before use.



c.
A129684

Remove the 2 O-rings.


d.

Using an E8 "TORX" socket wrench, remove the 2 stud bolts.

A387461E01
0.144,0.161 6.979,2.44 6.835,2.278 0.144,2.492 6.979,4.77 6.835,2.278 0.185,0.204 0.451,0.437 0.266,0.234 12 *A 0.199,2.534 0.465,2.768 0.266,0.234 12 *B 1.517,0.431 1.798,0.653 0.282,0.222 10 *a 5.342,0.225 5.659,0.496 0.316,0.272 10 *b 2.986,2.581 3.302,2.853 0.316,0.272 10 *b

Text in Illustration
*A Type A *B Type B
*a Timing Chain Cover Sub-assembly Side *b Cylinder Block Sub-assembly Bottom Side


Hide 12121 22.REMOVE NO.1 OIL PAN BAFFLE PLATE

a.
A129685

Remove the 7 bolts and No. 1 oil pan baffle plate.


Hide 11381 23.REMOVE ENGINE REAR OIL SEAL RETAINER

a.
A129686

Remove the 6 bolts.


b.
A129687E08
1.021,0.5 1.313,0.781 0.292,0.281 10 true Pry

Using a screwdriver, pry out the engine rear oil seal retainer.

NOTICE:

Be careful not to damage the engine rear oil seal retainer.


HINT:

Tape the screwdriver tip before use.



Hide 11381A 24.REMOVE ENGINE REAR OIL SEAL

a.
A131834E02
0.111,0.051 0.729,0.508 0.618,0.457 10 Wooden Block 2.652,1.296 2.652,0.253 2.652,0.253 0.806,0.253 false 1.08,1.33 1.08,0.253 false

Place the engine rear oil seal retainer on wooden blocks.

NOTICE:

Be careful not to damage the engine rear oil seal retainer.



b.

Using a screwdriver and a hammer, tap out the engine rear oil seal.

HINT:

Tape the screwdriver tip before use.



Hide 16100 25.REMOVE WATER PUMP ASSEMBLY

a.
A129688

Remove the 16 bolts, water pump assembly and water pump gasket.


Hide 11302 26.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A129689E04
2.51,1.74 2.938,1.969 0.427,0.229 10 false Nut 0.656,1.917 1.083,2.146 0.427,0.229 10 false Nut

Remove the 15 bolts and 2 nuts shown in the illustration.


b.
A129690E14
0.5,3.969 1.344,4.292 1.344,4.292 2.938,3.979 false 1.969,0.552 0.74,2.052 0.74,2.052 0.729,1.125 false 2.406,0.938 0.729,2.073 false 0.135,2.094 1.135,2.427 1,0.333 10 true Protective Tape 1.052,4.313 2.052,4.646 1,0.333 10 false Protective Tape

Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head sub-assembly or cylinder block sub-assembly with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly, cylinder block sub-assembly and timing chain cover sub-assembly.


HINT:

Tape the screwdriver tip before use.



c.

Remove the 4 bolts, chain cover plate and chain cover plate gasket.


d.
U113567

Remove the gasket.


Hide 11301C 27.REMOVE TIMING CHAIN CASE OIL SEAL

a.
U188266E02
1.938,1.271 1.521,1.5 1.521,1.5 1.396,1.5 false 0.25,0.031 1.24,0.406 0.99,0.375 10 true Protective Tape 0.448,1.396 1.375,1.75 0.927,0.354 10 true Wooden Block

Using a screwdriver, pry out the timing chain case oil seal.

HINT:

Tape the screwdriver tip before use.



Hide 28.SET NO. 1 CYLINDER TO TDC / COMPRESSION

a.

Temporarily tighten the pulley set bolt.


b.
A129691E11
0.646,0.604 0.646,1.417 0.646,1.417 1.604,0.927 false 0.438,0.177 1.292,0.083 false 2.406,1.438 2.615,1.646 false 0.104,1.417 0.969,1.792 0.865,0.375 10 true Timing Marks 1.323,0.021 2.083,0.365 0.76,0.344 10 true Center Line 2.417,1.646 3.25,2.115 0.833,0.469 10 true Sensor Plate

Set the timing mark on the crank angle sensor plate to the RH block bore center line (TDC/compression).


c.

Check that the timing marks of the camshaft timing gear assemblies are aligned with those of the camshaft bearing cap as shown in the illustration.

A395028E01
0.656,0.667 1.333,1.417 1.333,1.417 1.927,0.74 false 0.656,1.042 1.333,1.417 1.333,1.417 1.938,1.167 false 5.396,1.979 6.083,2.333 6.083,2.333 6.542,1.833 false 5.406,1.5 6.083,2.333 6.083,2.333 6.552,1.542 false 0.958,1.458 1.927,1.698 0.969,0.24 10 false Timing Marks 5.729,2.365 6.698,2.604 0.969,0.24 10 false Timing Marks

If not, turn the crankshaft 1 revolution (360°) and align the timing marks as above.


Hide 13540 29.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A124589E25
1.063,1.104 1.448,1.76 1.448,1.76 2.656,1.177 false 2.688,1.729 2.875,1.729 false 1.146,0.875 0.958,0.135 0.958,0.135 0.854,0.135 false 2.802,0.885 2.646,0.135 2.646,0.135 2.521,0.135 false 0.208,0.042 0.833,0.438 0.625,0.396 10 true Plunger 1.875,0.042 2.49,0.354 0.615,0.313 10 true Plunger 0.958,1.76 1.875,2.063 0.917,0.302 10 true Stopper Plate 2.885,1.646 3.24,1.917 0.354,0.271 10 true Pin

Move the stopper plate upward to release the lock, and push the plunger deep into the No. 1 chain tensioner assembly.


b.

Move the stopper plate downward to set the lock, and insert a pin of 1.27 mm (0.05 in.) diameter into the stopper plate's hole.


c.
A095165

Remove the 2 bolts and No. 1 chain tensioner assembly.


Hide 13559 30.REMOVE CHAIN TENSIONER SLIPPER

a.

Remove the chain tensioner slipper.


Hide 13506 31.REMOVE CHAIN SUB-ASSEMBLY

a.
A134897E07
0.51,0.677 0.698,1.531 0.698,1.531 1.604,0.927 false 0.438,0.167 1.51,0.167 false 2.438,1.323 2.813,1.469 2.813,1.469 2.813,1.688 false 2.417,1.688 3.26,2.094 0.844,0.406 10 true Sensor Plate 0.156,1.531 1.073,1.896 0.917,0.365 10 true Timing Mark 1.531,0.073 2.354,0.458 0.823,0.385 10 true Center Line 0.167,0.229 0.417,0.427 0.25,0.198 10 true 10°

Turn the crankshaft counterclockwise 10° to loosen the chain sub-assembly from the crankshaft timing sprocket.


b.

Remove the pulley set bolt.


c.
A134890

Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.


d.
A395918E01
0.135,0.115 0.708,0.333 0.573,0.219 12 false Bank 1:

Turn the camshaft timing gear assembly on bank 1 clockwise (approximately 60°) and set it as shown in the illustration. Be sure to loosen the chain sub-assembly between the banks.


e.

Remove the chain sub-assembly.


Hide 13530 32.REMOVE IDLE SPROCKET ASSEMBLY

a.
A129695

Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, idle sprocket assembly and No. 1 idle gear shaft.


Hide 13561 33.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A129696

Remove the 2 bolts and No. 1 chain vibration damper.


Hide 13562 34.REMOVE NO. 2 CHAIN VIBRATION DAMPER

a.

Remove the 2 No. 2 chain vibration dampers.


Hide 13521 35.REMOVE CRANKSHAFT TIMING SPROCKET

a.
A109720

Remove the crankshaft timing sprocket from the crankshaft.


b.

Remove the 2 keys from the crankshaft.


Hide 36.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

a.
A120651E21
1.667,2.573 1.906,2.885 1.906,2.885 2.031,2.885 false 1.333,2.646 1.844,3.135 1.844,3.135 1.969,3.135 false 2.406,1.208 2.76,1.51 0.354,0.302 10 true Push 2.052,2.802 2.292,2.948 0.24,0.146 10 false Pin 2,3.073 2.521,3.219 0.521,0.146 10 false Plunger

While raising the No. 2 chain tensioner assembly, insert a pin of 1.0 mm (0.039 in.) diameter into the hole to secure the No. 2 chain tensioner assembly.


b.
A120652E01
2.621,0.632 2.935,0.778 0.313,0.146 10 Turn 0.461,0.4 0.774,0.546 0.313,0.146 10 Hold

Hold the hexagonal portion of the camshaft with a wrench, and remove the 2 bolts and camshaft timing gear assembly and camshaft timing exhaust gear assembly RH.

NOTICE:
·

Be careful not to damage the cylinder head sub-assembly with the wrench.

·

Do not disassemble the camshaft timing gear assembly and camshaft timing exhaust gear assembly RH.




c.

Remove the No. 2 chain sub-assembly.


Hide 13550 37.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A109721

Remove the bolt and No. 2 chain tensioner assembly.


Hide 38.REMOVE CAMSHAFT BEARING CAP (for Bank 1)

a.
A129700E19
1.115,2.531 1.625,3.042 1.625,3.042 2.51,2.563 false 1.313,2.198 2.021,2.385 0.708,0.188 10 false Front View 1.292,3.083 1.958,3.271 0.667,0.188 10 false Knock Pin 2.99,2.271 3.24,2.458 0.25,0.188 10 false 45°

Check that the camshafts are positioned as shown in the illustration.


b.
A129701E16
0.625,1.771 0.76,1.927 0.135,0.156 10 true 1 2.854,1.74 2.99,1.896 0.135,0.156 10 true 3 2.854,0.125 2.99,0.281 0.135,0.156 10 true 4 1.396,1.771 1.531,1.927 0.135,0.156 10 true 5 1.365,0.156 1.5,0.313 0.135,0.156 10 true 6 2.156,1.771 2.292,1.927 0.135,0.156 10 true 7 2.146,0.156 2.281,0.313 0.135,0.156 10 true 8 0.646,0.177 0.781,0.333 0.135,0.156 10 true 2

Uniformly loosen and remove the 8 bearing cap bolts in the sequence shown in the illustration.


c.
A129702E08
0.146,1.729 0.281,1.885 0.135,0.156 10 false 5 0.156,1.063 0.292,1.219 0.135,0.156 10 true 6 0.104,0.542 0.24,0.698 0.135,0.156 10 false 4 3.198,0.635 3.344,0.813 0.146,0.177 10 true 1 2.521,0.688 2.698,0.844 0.177,0.156 10 true 10 2.531,1.177 2.708,1.344 0.177,0.167 10 true 12 2.552,1.833 2.76,2.01 0.208,0.177 10 true 11 3.24,1.125 3.375,1.281 0.135,0.156 10 false 3 3.281,1.667 3.417,1.823 0.135,0.156 10 false 2 0.958,0.521 1.094,0.677 0.135,0.156 10 true 7 0.948,1.083 1.083,1.24 0.135,0.156 10 true 9 0.927,1.74 1.073,1.917 0.146,0.177 10 true 8

Uniformly loosen and remove the 12 bearing cap bolts in the sequence shown in the illustration.

NOTICE:

Uniformly loosen the bolts while keeping the camshaft level.



d.

Remove the 5 camshaft bearing caps.


Hide 13511 39.REMOVE CAMSHAFT

a.

Remove the camshaft.


Hide 13512 40.REMOVE NO. 2 CAMSHAFT

a.

Remove the No. 2 camshaft.


Hide 11103C 41.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH

a.
A129703E01
0.106,3.437 1.123,3.620 1.017,0.184 10 Protective Tape 2.043,3.717 3.060,3.901 1.017,0.184 10 Protective Tape 0.637,2.233 0.637,3.414 0.637,3.414 1.581,2.839 false 2.433,2.922 2.433,3.717 2.433,3.717 3.208,2.644 false

Remove the camshaft housing sub-assembly RH by prying between the cylinder head sub-assembly RH and camshaft housing sub-assembly RH with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly and camshaft housing sub-assembly RH.


HINT:

Tape the screwdriver tip before use.



Hide 42.REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

a.
A120657E20
1.802,2.125 1.5,2.51 1.5,2.51 1.375,2.51 false 2,2.25 1.563,2.896 1.563,2.896 1.438,2.896 false 1.094,2.427 1.323,2.573 0.229,0.146 10 false Pin 2.177,0.427 2.552,0.698 0.375,0.271 10 true Push 0.813,2.781 1.323,3.021 0.51,0.24 10 false Plunger

While pushing down the No. 3 chain tensioner assembly, insert a pin of 1.0 mm (0.039 in.) diameter into the hole to secure the No. 3 chain tensioner assembly.


b.
A120658E01
1.029,0.639 1.338,0.783 0.309,0.144 10 Turn 2.952,0.529 3.262,0.673 0.309,0.144 10 Hold

Hold the hexagonal portion of the camshaft with a wrench, and remove the 2 bolts and camshaft timing gear assembly and camshaft timing exhaust gear assembly LH.

NOTICE:
·

Be careful not to damage the cylinder head sub-assembly with the wrench.

·

Do not disassemble the camshaft timing gear assembly and camshaft timing exhaust gear assembly LH.




c.

Remove the No. 2 chain sub-assembly.


Hide 13560A 43.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

a.
A109722

Remove the bolt and No. 3 chain tensioner assembly.


Hide 44.REMOVE CAMSHAFT BEARING CAP (for Bank 2)

a.
A129706E01
1.293,2.156 1.982,2.312 0.689,0.156 10 Front View 1.345,3.055 1.992,3.211 0.647,0.156 10 Knock Pin 1.074,2.535 1.664,3.055 1.664,3.055 2.319,2.527 false

Check that the camshafts are positioned as shown in the illustration.


b.
A134891E18
3.208,1.292 3.365,1.5 0.156,0.208 10 true 1 3.188,0.573 3.344,0.771 0.156,0.198 10 true 2 0.042,1.271 0.146,1.469 0.104,0.198 10 true 3 0.063,0.531 0.177,0.729 0.115,0.198 10 true 4 2.49,1.271 2.625,1.448 0.135,0.177 10 true 5 2.5,0.604 2.677,0.813 0.177,0.208 10 true 6 0.958,1.313 1.094,1.49 0.135,0.177 10 true 7 0.948,0.583 1.083,0.792 0.135,0.208 10 true 8

Uniformly loosen and remove the 8 bearing cap bolts in the sequence shown in the illustration.


c.
A129708E08
0.115,0.24 0.25,0.396 0.135,0.156 10 false 5 2.448,0.396 2.635,0.573 0.188,0.177 10 true 8 2.406,0.958 2.542,1.115 0.135,0.156 10 true 4 2.51,1.583 2.677,1.76 0.167,0.177 10 true 9 3.198,1.698 3.333,1.854 0.135,0.156 10 false 3 3.26,1.333 3.396,1.49 0.135,0.156 10 true 1 3.26,0.542 3.396,0.698 0.135,0.156 10 false 2 0.115,0.979 0.25,1.135 0.135,0.156 10 false 7 0.115,1.729 0.25,1.885 0.135,0.156 10 false 6 0.958,0.5 1.167,0.688 0.208,0.188 10 true 11 0.958,1.052 1.188,1.24 0.229,0.188 10 true 13 0.958,1.688 1.188,1.896 0.229,0.208 10 true 12 1.698,1.052 1.896,1.24 0.198,0.188 10 true 10

Uniformly loosen and remove the 13 bearing cap bolts in the sequence shown in the illustration.

NOTICE:

Uniformly loosen the bolts while keeping the camshaft level.



d.

Remove the 5 camshaft bearing caps.


Hide 13053 45.REMOVE NO. 3 CAMSHAFT

a.

Remove the No. 3 camshaft.


Hide 13054 46.REMOVE NO. 4 CAMSHAFT

a.

Remove the No. 4 camshaft.


Hide 11104A 47.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

a.
A129709E01
0.133,4.07 1.136,4.226 1.003,0.156 10 Protective Tape 2.551,3.446 3.214,3.764 0.663,0.318 10 Protective Tape 0.624,2.901 0.624,4.036 0.624,4.036 1.889,3.667 false 2.923,2.753 2.923,3.475 false

Remove the camshaft housing sub-assembly LH by prying between the cylinder head sub-assembly LH and camshaft housing sub-assembly LH with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly and camshaft housing sub-assembly LH.


HINT:

Tape the screwdriver tip before use.



Hide 13801 48.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Remove the 24 No. 1 valve rocker arm sub-assemblies.

HINT:

Arrange the removed parts in the correct order.



Hide 13750 49.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.

Remove the 24 valve lash adjuster assemblies from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in the correct order.



Hide 11101 50.REMOVE CYLINDER HEAD SUB-ASSEMBLY RH

a.
A129712E14
2.854,0.104 2.99,0.26 0.135,0.156 10 true 3 2.073,0.115 2.208,0.271 0.135,0.156 10 true 5 1.313,0.115 1.448,0.271 0.135,0.156 10 true 7 0.552,0.115 0.688,0.271 0.135,0.156 10 true 2 2.896,1.677 3.031,1.833 0.135,0.156 10 true 1 2.073,1.688 2.208,1.844 0.135,0.156 10 true 8 1.313,1.688 1.448,1.844 0.135,0.156 10 true 6 0.479,1.688 0.615,1.844 0.135,0.156 10 true 4

Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

NOTICE:
·

Be careful not to drop the plate washers into the cylinder head sub-assembly RH.

·

Warpage or cracking of the cylinder head sub-assembly RH could result from removing the bolts in an incorrect order.



HINT:

Arrange the removed parts in the correct order.



b.

Remove the cylinder head sub-assembly RH and cylinder head gasket.


Hide 11102 51.REMOVE CYLINDER HEAD SUB-ASSEMBLY LH

a.
A129710E01
0.141,0.77 0.275,0.926 0.133,0.156 10 2 0.073,1.389 0.206,1.545 0.133,0.156 10 1

Uniformly loosen and remove the 2 cylinder head set bolts in the sequence shown in the illustration.


b.
A129711E13
0.771,0.323 0.906,0.479 0.135,0.156 10 true 1 1.469,0.323 1.604,0.479 0.135,0.156 10 true 8 2.177,0.333 2.313,0.49 0.135,0.156 10 true 6 2.906,0.323 3.042,0.479 0.135,0.156 10 true 4 0.729,1.833 0.865,1.99 0.135,0.156 10 true 3 1.469,1.833 1.604,1.99 0.135,0.156 10 true 5 2.208,1.823 2.344,1.979 0.135,0.156 10 true 7 2.938,1.813 3.073,1.969 0.135,0.156 10 true 2

Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

NOTICE:
·

Be careful not to drop the plate washers into the cylinder head sub-assembly LH.

·

Warpage or cracking of the cylinder head sub-assembly LH could result from removing the bolts in an incorrect order.



HINT:

Arrange the removed parts in the correct order.



c.

Remove the cylinder head sub-assembly LH and No. 2 cylinder head gasket.


Hide 16322 52.REMOVE WATER INLET PIPE

a.

Slide the clip and disconnect the No. 1 water by-pass hose.


b.
A160595

Remove the 2 bolts and water inlet pipe.


Hide 13716 53.REMOVE VALVE STEM CAP

a.

Remove the 24 valve stem caps from the cylinder head sub-assemblies.

HINT:

Arrange the removed parts in the correct order.



Hide 13711 54.REMOVE INTAKE VALVE

HINT:
A336090E02
0.052,0.063 1.698,4.5 1.646,4.438 1.781,0.063 3.385,4.5 1.604,4.438 1.146,2.094 1.146,2.354 false 2.854,2.083 2.854,2.344 false 2.604,2.979 2.885,2.979 false 0.896,3.01 1.167,3.01 false 0.958,3.802 1.229,3.802 false 2.656,3.885 2.927,3.885 false 0.104,0.083 0.5,0.333 0.396,0.25 12 false *A 1.833,0.083 2.229,0.333 0.396,0.25 12 false *B 1.396,0.885 1.667,1.125 0.271,0.24 10 false *b 3.125,0.875 3.344,1.115 0.219,0.24 10 false *b 1.042,2.354 1.313,2.594 0.271,0.24 10 false *1 2.771,2.354 3.042,2.594 0.271,0.24 10 false *1 0.615,2.458 0.885,2.698 0.271,0.24 10 false *a 2.344,2.479 2.615,2.719 0.271,0.24 10 false *a 2.917,2.896 3.188,3.135 0.271,0.24 10 false *2 1.229,2.917 1.5,3.156 0.271,0.24 10 false *2 1.281,3.708 1.552,3.948 0.271,0.24 10 false *3 2.99,3.781 3.26,4.021 0.271,0.24 10 false *3

Type A and Type B can be distinguished by the shape of the inner compression spring.

Text in Illustration
*A Type A
*B Type B
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Spring Retainer
*3 Inner Compression Spring
*a Valve Spring Retainer Diameter
*b No. 1 Valve Rocker Arm Sub-assembly Roller Width

Type No. 1 Valve Rocker Arm Sub-assembly Roller Width Valve Spring Retainer Diameter Inner Compression Spring Shape
A 10.7 mm (0.421 in.) 23.4 mm (0.921 in.) Straight
B 8.0 mm (0.315 in.) 18.9 mm (0.744 in.) Taper


a.

Type A:

i.
A129714E01
1.7,0.262 2.011,0.418 0.311,0.156 10 SST 1.397,0.644 1.678,0.335 false

Using SST, compress the inner compression spring and remove the valve spring retainer locks.

SST
09202-70020  (09202-00010)



b.

Type B:

i.
A333600E02
1.323,0.406 1.49,0.26 1.49,0.26 1.688,0.26 false 1.75,0.177 2.156,0.479 0.406,0.302 10 false SST

Using SST, compress the inner compression spring and remove the valve spring retainer locks.

SST
09202-70020  
09202-00020  



c.

Remove the valve spring retainer, inner compression spring and intake valve.

HINT:

Arrange the removed parts in the correct order.



Hide 13715 55.REMOVE EXHAUST VALVE

HINT:
A336090E02
0.052,0.063 1.698,4.5 1.646,4.438 1.781,0.063 3.385,4.5 1.604,4.438 1.146,2.094 1.146,2.354 false 2.854,2.083 2.854,2.344 false 2.604,2.979 2.885,2.979 false 0.896,3.01 1.167,3.01 false 0.958,3.802 1.229,3.802 false 2.656,3.885 2.927,3.885 false 0.104,0.083 0.5,0.333 0.396,0.25 12 false *A 1.833,0.083 2.229,0.333 0.396,0.25 12 false *B 1.396,0.885 1.667,1.125 0.271,0.24 10 false *b 3.125,0.875 3.344,1.115 0.219,0.24 10 false *b 1.042,2.354 1.313,2.594 0.271,0.24 10 false *1 2.771,2.354 3.042,2.594 0.271,0.24 10 false *1 0.615,2.458 0.885,2.698 0.271,0.24 10 false *a 2.344,2.479 2.615,2.719 0.271,0.24 10 false *a 2.917,2.896 3.188,3.135 0.271,0.24 10 false *2 1.229,2.917 1.5,3.156 0.271,0.24 10 false *2 1.281,3.708 1.552,3.948 0.271,0.24 10 false *3 2.99,3.781 3.26,4.021 0.271,0.24 10 false *3

Type A and Type B can be distinguished by the shape of the inner compression spring.

Text in Illustration
*A Type A
*B Type B
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Spring Retainer
*3 Inner Compression Spring
*a Valve Spring Retainer Diameter
*b No. 1 Valve Rocker Arm Sub-assembly Roller Width

Type No. 1 Valve Rocker Arm Sub-assembly Roller Width Valve Spring Retainer Diameter Inner Compression Spring Shape
A 10.7 mm (0.421 in.) 23.4 mm (0.921 in.) Straight
B 8.0 mm (0.315 in.) 18.9 mm (0.744 in.) Taper


a.

Type A:

i.
A129715E01
1.619,0.279 1.930,0.435 0.311,0.156 10 SST 2,0.358 2.29,0.645 false

Using SST, compress the inner compression spring and remove the valve spring retainer locks.

SST
09202-70020  (09202-00010)



b.

Type B:

i.
A333601E01
2.304,0.485 2.126,0.247 2.126,0.247 1.953,0.247 false 1.588,0.162 2.036,0.395 0.448,0.232 10 SST

Using SST, compress the inner compression spring and remove the valve spring retainer locks.

SST
09202-70020  
09202-00020  



c.

Remove the valve spring retainer, inner compression spring and exhaust valve.

HINT:

Arrange the removed parts in the correct order.



Hide 56.REMOVE VALVE STEM OIL SEAL

a.
A384416

Using needle-nose pliers, remove the 24 valve stem oil seals.


Hide 13734 57.REMOVE VALVE SPRING SEAT

a.
A384417

Using compressed air and a magnet hand, remove the 24 valve spring seats by blowing air onto them.


Hide 11117E 58.REMOVE NO. 1 STRAIGHT SCREW PLUG

a.
A129718E19
0.042,0.063 0.688,0.406 0.646,0.344 10 true Bank 1: 0.042,2.458 0.698,2.813 0.656,0.354 10 true Bank 2:

Using a 10 mm hexagon wrench, remove the 4 No. 1 straight screw plugs and 4 gaskets.

NOTICE:

If water leaks from a No. 1 straight screw plug or the plug is corroded, replace it.



Hide 11117F 59.REMOVE NO. 2 STRAIGHT SCREW PLUG

a.
A306458E01
0.148,0 0.840,0.181 0.692,0.181 10 Bank 1: 0.139,2.138 0.901,2.486 0.762,0.348 10 Bank 2:

Using a 14 mm hexagon wrench, remove the 2 No. 2 straight screw plugs and 2 gaskets.

NOTICE:

If water leaks from a No. 2 straight screw plug or the plug is corroded, replace it.



Hide 60.REMOVE RING PIN

NOTICE:

It is not necessary to remove the ring pin unless it is being replaced.


Hide 61.REMOVE STUD BOLT

NOTICE:

If the stud bolt is deformed or the threads are damaged, replace it.


Hide 62.REMOVE STRAIGHT PIN

NOTICE:

If the straight pin is deformed replace it.


Hide 11122 63.REMOVE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.


c.
A121839E02
2.146,0.004 2.474,0.167 0.329,0.163 10 SST 0.694,1.436 1.023,1.599 0.329,0.163 10 SST 1.713,0.723 2.009,0.089 2.009,0.089 2.124,0.089 false 1.739,1.179 0.917,1.319 0.917,1.319 0.917,1.411 false

Using SST and a hammer, tap out the intake valve guide bushes.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


Hide 11126 64.REMOVE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head sub-assembly on wooden blocks.


c.
A120709E02
1.245,0.049 1.549,0.189 0.304,0.141 10 SST 2.978,1.414 3.298,1.575 0.320,0.161 10 SST 2.148,0.557 1.813,0.126 1.813,0.126 1.624,0.126 false 2.109,1.133 2.819,1.511 2.819,1.511 2.941,1.511 false

Using SST and a hammer, tap out the exhaust valve guide bushes.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


Hide 65.REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Check that the matchmarks on the connecting rod sub-assembly and connecting rod cap are aligned.

HINT:

The matchmarks on the connecting rod sub-assembly and connecting rod caps are provided to ensure correct reassembly.



b.
A383470E03
0.458,0.469 1.604,0.802 1.146,0.333 10 false Engine Front

Remove the 2 connecting rod cap bolts.


c.
A129761

Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and connecting rod bearing by wiggling the connecting rod cap back and forth.

HINT:

Keep the connecting rod bearing inserted in the connecting rod cap.



d.
A129720E03
2.021,0.688 1.5,0.167 false 0.531,0.042 1.469,0.49 0.938,0.448 10 true Ridge Reamer

Using a ridge reamer, remove all the carbon from the top of the cylinder.


e.

Push the piston, connecting rod sub-assembly and connecting rod bearing through the top of the cylinder block sub-assembly.

HINT:
·

Keep the connecting rod bearing, connecting rod sub-assembly and connecting rod cap together.

·

Arrange the pistons and connecting rod sub-assemblies in the correct order.




Hide 13041 66.REMOVE CONNECTING ROD BEARING

HINT:

Arrange the removed parts in the correct order.


Hide 13411 67.REMOVE CRANKSHAFT

a.
U113571E06
1.5,0.146 1.594,0.302 0.094,0.156 10 false 5 1.177,0.344 1.292,0.542 0.115,0.198 10 true 8 0.792,0.531 0.885,0.688 0.094,0.156 10 false 7 0.208,0.958 0.302,1.115 0.094,0.156 10 false 6 2.042,1.896 2.198,2.083 0.156,0.188 10 true 1 2.438,1.563 2.583,1.76 0.146,0.198 10 true 4 2.844,1.271 2.969,1.448 0.125,0.177 10 true 3 3.271,1.094 3.365,1.25 0.094,0.156 10 false 2

Uniformly loosen and remove the 8 crankshaft bearing cap bolts and seal washers in several steps and in the sequence shown in the illustration.


b.
A134892E11
0.385,1.521 0.521,1.74 0.135,0.219 10 true 1 0.344,0.219 0.531,0.385 0.188,0.167 10 true 2 3.01,1.521 3.167,1.729 0.156,0.208 10 false 3 3.042,0.281 3.208,0.448 0.167,0.167 10 false 4 1,1.49 1.156,1.698 0.156,0.208 10 true 5 1.01,0.26 1.167,0.427 0.156,0.167 10 true 6 2.375,1.521 2.542,1.667 0.167,0.146 10 true 7 2.365,0.271 2.531,0.438 0.167,0.167 10 true 8 0.302,1.021 0.469,1.229 0.167,0.208 10 true 9 0.24,0.688 0.448,0.896 0.208,0.208 10 false 10 3.042,1.021 3.344,1.24 0.302,0.219 10 false 11 3.052,0.698 3.25,0.906 0.198,0.208 10 false 12 0.896,1.021 1.094,1.229 0.198,0.208 10 true 13 0.885,0.698 1.115,0.906 0.229,0.208 10 true 14 2.385,1.01 2.615,1.198 0.229,0.188 10 true 15 2.385,0.698 2.604,0.875 0.219,0.177 10 true 16

Uniformly loosen the 16 crankshaft bearing cap bolts in several steps and in the sequence shown in the illustration.


c.
A122567E14
1.854,1.438 2.615,2.323 false 0.083,4.104 1.021,4.302 0.938,0.198 10 false Joint Surface 2.031,2.375 3.094,2.573 1.063,0.198 10 false Protective Tape 1.854,2.896 2.781,3.135 0.927,0.24 10 false Bearing Cap 0.292,2.75 0.854,3.74 0.563,0.99 10 false Cylinder Block Sub-assembly

Using a screwdriver, pry out the main crankshaft bearing caps. Remove the 4 crankshaft bearing caps and lower crankshaft bearings.

NOTICE:
·

Push up on the cap little by little, from the right and left side alternately so that the cap can be removed.

·

Be careful not to damage the joint surfaces of the cylinder block sub-assembly and the main crankshaft bearing cap.



HINT:

Tape the screwdriver tip before use.



d.

Remove the crankshaft.


Hide 11711 68.REMOVE CRANKSHAFT BEARING

a.

Remove the upper crankshaft bearing and lower crankshaft bearing.

HINT:

Arrange the removed parts in the correct order.



Hide 11011 69.REMOVE UPPER CRANKSHAFT THRUST WASHER

a.
A109726

Remove the 2 upper crankshaft thrust washers from the cylinder block sub-assembly.


Hide 13011 70.REMOVE PISTON RING SET

a.
A129724E01
0.093,0.318 0.840,0.717 0.746,0.399 10 Piston Ring Expander 1.016,0.454 1.503,0.454 false

Using a piston ring expander, remove the No. 1 compression ring and No. 2 compression ring.


b.

Remove the oil ring expander and side rail upper and side rail lower by hand.

HINT:

Arrange the removed parts in the correct order.



Hide 13101 71.REMOVE PISTON SUB-ASSEMBLY WITH PIN

a.
A129725

Check the fitting condition between the piston sub-assembly with pin.

i.

Try to move the piston back and forth on the piston pin.

If any movement is felt, replace the piston sub-assembly with pin as a set.



b.
A129726

Disconnect the connecting rod sub-assembly from the piston.

i.

Using a screwdriver, pry out the 2 snap rings from the piston.


ii.
A109729E02
0.14,0.025 1.329,0.205 1.189,0.180 10 80°C (176°F)

Gradually heat each piston to approximately 80°C (176°F).


iii.
A129728

Using a brass bar and plastic hammer, lightly tap out the piston pin and remove the connecting rod sub-assembly.

HINT:
·

The piston sub-assembly with pin are a matched set.

·

Arrange the pistons, piston pins, piston rings connecting rod sub-assemblies and connecting rod bearings in the correct order.





c.
A129729

Using a gasket scraper, remove any carbon from the piston top.


d.
A129730

Using a groove cleaning tool or broken ring, clean the piston ring grooves.


e.
A129731

Using solvent and a brush, thoroughly clean the piston.

NOTICE:

Do not use a wire brush.



Hide 15708 72.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A120734

Using a 5 mm hexagon wrench, remove the 3 bolts and 3 No. 1 oil nozzle sub-assemblies.


b.

Check the 3 No. 1 oil nozzle sub-assemblies for damage or clogging.

If necessary, replace the No. 1 oil nozzle sub-assembly.


Hide 73.CLEAN CYLINDER BLOCK SUB-ASSEMBLY