Home › Engine / Hybrid System › 2AZ-FE COOLING › COOLING FAN RELAY
RM24M0E _51 Engine / Hybrid System _059552 2AZ-FE COOLING _0291852 COOLING FAN RELAY G

2AZ-FE COOLING  COOLING FAN RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


Hide 82662B 2.REMOVE ENGINE ROOM NO. 2 RELAY BLOCK COVER

Hide 85927 3.INSPECT NO. 1 FAN RELAY (Marking: FAN NO. 1)

B426341E04
2.625,0.708 2.969,0.708 false 2.031,0.708 1.698,0.708 false 2.458,1.135 2.948,1.135 false 2.448,1.625 2.938,1.625 false 0.24,0.76 0.458,0.979 0.219,0.219 10 false 3 0.229,1.323 0.448,1.542 0.219,0.219 10 false 1 1.198,0.76 1.417,0.979 0.219,0.219 10 false 5 1.177,1.313 1.396,1.531 0.219,0.219 10 false 2 1.448,0.635 1.667,0.854 0.219,0.219 10 false 1 3.01,1.031 3.229,1.25 0.219,0.219 10 false 5 3,1.521 3.219,1.74 0.219,0.219 10 false 3 3.052,0.594 3.271,0.813 0.219,0.219 10 false 2

a.

Remove the relay from the engine room No. 2 relay block.


b.

Measure the resistance of the relay.

Standard resistance:
Tester Connection Specified Condition
3 - 5 10 Ω or higher
3 - 5 Below 1 Ω
(when battery voltage is applied to terminals 1 and 2)


If the result is not as specified, replace the relay.



c.

Install the relay.


Hide 85927A 4.INSPECT NO. 2 FAN RELAY (Marking: FAN NO. 2)

A087121E52
2.333,0.604 2.333,0.292 false 2.5,1.125 2.969,1.125 false 2.5,1.625 2.969,1.625 false 2.021,0.604 1.844,0.292 false 2.615,0.604 2.792,0.292 false 0.313,1.396 0.51,1.604 0.198,0.208 10 false 1 1.813,0.083 2.01,0.292 0.198,0.208 10 false 1 1.313,1.396 1.51,1.604 0.198,0.208 10 false 2 2.76,0.083 2.958,0.292 0.198,0.208 10 false 2 0.313,0.844 0.51,1.052 0.198,0.208 10 false 3 3.031,1.531 3.229,1.74 0.198,0.208 10 false 3 0.938,0.365 1.135,0.573 0.198,0.208 10 false 4 2.302,0.083 2.5,0.292 0.198,0.208 10 false 4 1.313,0.844 1.51,1.052 0.198,0.208 10 false 5 3.021,1.021 3.219,1.229 0.198,0.208 10 false 5

a.

Remove the relay from the engine room No. 2 relay block.


b.

Measure the resistance of the relay.

Standard resistance:
Tester Connection Specified Condition
3 - 4 Below 1 Ω
3 - 5 10 Ω or higher
3 - 4 10 Ω or higher
(when battery voltage is applied to terminals 1 and 2)
3 - 5 Below 1 Ω
(when battery voltage is applied to terminals 1 and 2)


If the result is not as specified, replace the relay.



c.

Install the relay.


Hide 85927B 5.INSPECT NO. 3 FAN RELAY (Marking: FAN NO. 3)

B426341E04
2.625,0.708 2.969,0.708 false 2.031,0.708 1.698,0.708 false 2.458,1.135 2.948,1.135 false 2.448,1.625 2.938,1.625 false 0.24,0.76 0.458,0.979 0.219,0.219 10 false 3 0.229,1.323 0.448,1.542 0.219,0.219 10 false 1 1.198,0.76 1.417,0.979 0.219,0.219 10 false 5 1.177,1.313 1.396,1.531 0.219,0.219 10 false 2 1.448,0.635 1.667,0.854 0.219,0.219 10 false 1 3.01,1.031 3.229,1.25 0.219,0.219 10 false 5 3,1.521 3.219,1.74 0.219,0.219 10 false 3 3.052,0.594 3.271,0.813 0.219,0.219 10 false 2

a.

Remove the relay from the engine room No. 2 relay block.


b.

Measure the resistance of the relay.

Standard resistance:
Tester Connection Specified Condition
3 - 5 10 Ω or higher
3 - 5 Below 1 Ω
(when battery voltage is applied to terminals 1 and 2)


If the result is not as specified, replace the relay.



c.

Install the relay.


Hide 82662B 6.INSTALL ENGINE ROOM NO. 2 RELAY BLOCK COVER

Hide 8.PERFORM INITIALIZATION

a.

Perform initialization (see page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

NOTICE:

Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.