Home › Engine / Hybrid System › 2GR-FE LUBRICATION › OIL PUMP › from 2016.05
RM24M0E _51 Engine / Hybrid System _059553 2GR-FE LUBRICATION _0291858 OIL PUMP A

2GR-FE LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 11301C 1.INSTALL TIMING CHAIN CASE OIL SEAL

a.
A125109E10
1.052,1.333 0.51,1.458 0.51,1.458 0.99,1.479 false 0.208,1.385 0.51,1.563 0.302,0.177 10 false SST

Using SST, tap in a new oil seal until its surface is flush with the timing chain case edge.

SST
09223-22010  
09506-35010  

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap on the oil seal at an angle.

·

Make sure that the oil seal edge does not stick out of the timing chain case.




Hide 11302 2.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

a.

Apply seal packing in a continuous line to the engine unit as shown in the following illustration.

A132228E19
4.813,2.208 5.01,2.406 0.198,0.198 5.156,1.635 5.354,1.833 0.198,0.198 4.115,1.333 4.021,1.49 false 5.271,0.969 5.271,0.344 false 4.656,2.177 4.844,2.302 4.844,2.302 4.74,2.469 false 5.25,1.5 5.26,1.656 5.26,1.656 5.427,1.583 false 6.521,1.135 6.521,1.385 false 3.906,1.531 4.042,1.708 0.135,0.177 10 false C 5.219,0.135 5.354,0.313 0.135,0.177 10 false C 4.865,2.229 5,2.406 0.135,0.177 10 false C 5.208,1.656 5.344,1.833 0.135,0.177 10 false C 6.479,1.417 6.615,1.594 0.135,0.177 10 false C 0.625,2.896 1.583,3.135 0.958,0.24 10 false : Seal Packing 3.854,3.833 5.75,4.177 1.896,0.344 10 false 3.0 mm (0.118 in.) or more

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal diameter:

3.0 mm (0.118 in.)


NOTICE:
·

Be sure to clean and degrease the contact surfaces, especially the surfaces indicated by C in the illustration.

·

When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.

·

Install the chain cover within 3 minutes.

·

Do not start the engine for at least 2 hours after installing.




b.

Apply seal packing in a continuous line to the timing chain cover as shown in the following illustration.

A134901E22
2.5,1.792 3.156,1.969 3.156,1.969 3.333,1.375 false 4,1.365 4.229,1.469 false 0.896,4.854 1.135,4.479 1.135,4.479 1.365,4.479 false 5.958,4.875 5.844,4.479 5.844,4.479 5.604,4.479 false 3.24,4.896 3.01,5.24 3.01,5.24 2.854,5.24 false 3.802,4.896 4.146,5.229 4.146,5.229 4.344,5.229 false 3.948,2.063 4.021,2.927 4.021,2.927 3.823,2.604 false 2.385,1.177 1.552,0.521 1.552,0.521 2.781,0.917 false 0.594,5.781 1.677,5.927 1.083,0.146 10 false Dashed line area 0.552,5.906 5.948,6.094 5.396,0.188 10 false (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent) 0.594,6.271 1.885,6.417 1.292,0.146 10 false Continuous line area 0.594,6.823 3.156,7 2.563,0.177 10 false Alternate long and short dashed line area 0.594,7.302 1.74,7.479 1.146,0.177 10 false Diagonal line area 1.396,4.313 2.115,4.688 0.719,0.375 10 false 5.0 mm (0.197 in.) 4.396,5.031 5.615,5.385 1.219,0.354 10 false 2.0 to 3.0 mm (0.079 to 0.118 in.) 1.667,5.052 2.906,5.427 1.24,0.375 10 false 3.0 to 4.0 mm (0.118 to 0.158 in.) 4.448,4.302 5.698,4.677 1.25,0.375 10 false 1.0 to 2.0 mm (0.039 to 0.079 in.) 3.365,2.927 4.396,3.698 1.031,0.771 10 true Be sure to apply seal packing 0.51,0.333 1.542,0.76 1.031,0.427 10 false Be sure to apply seal packing 4.25,1.302 4.906,1.948 0.656,0.646 10 true 20 mm (0.787 in.) 2.938,1.979 3.604,2.635 0.667,0.656 10 true 20 mm (0.787 in.) 0.573,7.479 6,7.667 5.427,0.188 10 false (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent) 0.594,6.417 5.958,6.604 5.365,0.188 10 false (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent) 0.573,7.021 6.073,7.208 5.5,0.188 10 false (Seal packing: Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent)

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent


NOTICE:
·

When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.

·

Install the chain cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

·

Do not start the engine for at least 2 hours after installing it.



Apply seal packing as follows:
Area Seal Packing Diameter Application Position from Inside Seal Line
Continuous Line Area 4.5 mm (0.177 in.) or more 3.0 to 4.0 mm (0.118 to 0.158 in.)
Alternate Long and Short Dashed Line Area 3.5 mm (0.138 in.) or more 2.0 to 3.0 mm (0.079 to 0.118 in.)
Dashed Line Area 3.5 mm (0.138 in.) or more 3.0 to 4.0 mm (0.118 to 0.158 in.)
Diagonal Line Area 6.0 mm (0.236 in.) or more 5.0 mm (0.197 in.)



c.
U145312

Install a new gasket.


d.
A132229E02
1.031,1.381 1.650,1.653 0.619,0.272 8 Drive Rotor Spline 2.801,1.365 3.290,1.704 0.489,0.339 10 Crankshaft 0.76,1.752 1.003,1.462 false 2.418,1.639 2.793,1.511 false

Align the oil pump's drive rotor spline and the crankshaft as shown in the illustration. Install the spline and chain cover to the crankshaft.


e.

Type X:

i.

Temporarily tighten the timing chain cover with the 23 bolts and 2 nuts.

A128019E10
4.354,1.479 4.052,1.479 false 3.75,0.958 3.75,0.688 false 5.229,0.479 5.396,0.323 5.396,0.323 5.552,0.51 false 6.885,0.958 6.885,0.667 false 6.188,1.427 6.448,1.427 false 6.313,1.729 6.552,1.729 false 4.667,2.229 4.49,2.229 false 5.094,1.438 5.094,1.302 false 0.115,1.271 0.271,1.417 0.156,0.146 10 false C 0.271,1.354 0.427,1.5 0.156,0.146 10 false C 0.406,1.49 0.563,1.635 0.156,0.146 10 false C 0.802,2.156 0.958,2.302 0.156,0.146 10 false C 3.115,1.229 3.271,1.375 0.156,0.146 10 false C 3.49,0.917 3.646,1.063 0.156,0.146 10 false B 1.802,0.135 1.958,0.281 0.156,0.146 10 false C 1.625,0.531 1.781,0.677 0.156,0.146 10 false C 1.135,0.531 1.292,0.677 0.156,0.146 10 false C 1.25,0.76 1.406,0.906 0.156,0.146 10 false C 1.313,0.958 1.469,1.104 0.156,0.146 10 false C 1.698,0.344 1.854,0.49 0.156,0.146 10 false A 0.521,1.646 0.677,1.792 0.156,0.146 10 false B 0.792,1.99 0.948,2.135 0.156,0.146 10 false B 1.385,1.906 1.542,2.052 0.156,0.146 10 false B 1.365,1.5 1.521,1.646 0.156,0.146 10 true B 1.135,1.417 1.292,1.563 0.156,0.146 10 true B 1.417,1.135 1.573,1.281 0.156,0.146 10 false B 1.958,1.625 2.115,1.771 0.156,0.146 10 true B 2.438,1.948 2.594,2.094 0.156,0.146 10 false B 2.208,1.125 2.365,1.271 0.156,0.146 10 true B 2.938,1.51 3.094,1.656 0.156,0.146 10 false B 2.979,1.344 3.135,1.49 0.156,0.146 10 false B 0.656,2.333 0.917,2.49 0.26,0.156 10 false Nut 2.604,2.313 2.865,2.469 0.26,0.156 10 false Nut 3.615,1.427 4.063,1.573 0.448,0.146 10 false Area 1 3.469,0.458 3.917,0.604 0.448,0.146 10 false Area 4 5.177,0.031 5.625,0.177 0.448,0.146 10 false Area 4 6.688,0.396 7.135,0.542 0.448,0.146 10 false Area 4 6.479,1.365 6.927,1.51 0.448,0.146 10 false Area 1 6.552,1.656 7,1.802 0.448,0.146 10 false Area 3 4.052,2.115 4.5,2.26 0.448,0.146 10 false Area 3 4.771,1.021 5.219,1.167 0.448,0.146 10 false Area 2

Bolt length
Item Length
Bolt A 40 mm (1.57 in.)
Bolt B 55 mm (2.17 in.)
Bolt C 25 mm (0.98 in.)

NOTICE:

Make sure that there is no oil on the bolt threads.




f.

Type Y:

i.

Temporarily tighten the timing chain cover with the 23 bolts and 2 nuts.

A128019E10
4.354,1.479 4.052,1.479 false 3.75,0.958 3.75,0.688 false 5.229,0.479 5.396,0.323 5.396,0.323 5.552,0.51 false 6.885,0.958 6.885,0.667 false 6.188,1.427 6.448,1.427 false 6.313,1.729 6.552,1.729 false 4.667,2.229 4.49,2.229 false 5.094,1.438 5.094,1.302 false 0.115,1.271 0.271,1.417 0.156,0.146 10 false C 0.271,1.354 0.427,1.5 0.156,0.146 10 false C 0.406,1.49 0.563,1.635 0.156,0.146 10 false C 0.802,2.156 0.958,2.302 0.156,0.146 10 false C 3.115,1.229 3.271,1.375 0.156,0.146 10 false C 3.49,0.917 3.646,1.063 0.156,0.146 10 false B 1.802,0.135 1.958,0.281 0.156,0.146 10 false C 1.625,0.531 1.781,0.677 0.156,0.146 10 false C 1.135,0.531 1.292,0.677 0.156,0.146 10 false C 1.25,0.76 1.406,0.906 0.156,0.146 10 false C 1.313,0.958 1.469,1.104 0.156,0.146 10 false C 1.698,0.344 1.854,0.49 0.156,0.146 10 false A 0.521,1.646 0.677,1.792 0.156,0.146 10 false B 0.792,1.99 0.948,2.135 0.156,0.146 10 false B 1.385,1.906 1.542,2.052 0.156,0.146 10 false B 1.365,1.5 1.521,1.646 0.156,0.146 10 true B 1.135,1.417 1.292,1.563 0.156,0.146 10 true B 1.417,1.135 1.573,1.281 0.156,0.146 10 false B 1.958,1.625 2.115,1.771 0.156,0.146 10 true B 2.438,1.948 2.594,2.094 0.156,0.146 10 false B 2.208,1.125 2.365,1.271 0.156,0.146 10 true B 2.938,1.51 3.094,1.656 0.156,0.146 10 false B 2.979,1.344 3.135,1.49 0.156,0.146 10 false B 0.656,2.333 0.917,2.49 0.26,0.156 10 false Nut 2.604,2.313 2.865,2.469 0.26,0.156 10 false Nut 3.615,1.427 4.063,1.573 0.448,0.146 10 false Area 1 3.469,0.458 3.917,0.604 0.448,0.146 10 false Area 4 5.177,0.031 5.625,0.177 0.448,0.146 10 false Area 4 6.688,0.396 7.135,0.542 0.448,0.146 10 false Area 4 6.479,1.365 6.927,1.51 0.448,0.146 10 false Area 1 6.552,1.656 7,1.802 0.448,0.146 10 false Area 3 4.052,2.115 4.5,2.26 0.448,0.146 10 false Area 3 4.771,1.021 5.219,1.167 0.448,0.146 10 false Area 2

Bolt length
Item Length
Bolt A 40 mm (1.57 in.)
Bolt B 55 mm (2.17 in.)
Bolt C 28 mm (1.102 in.)

NOTICE:

Make sure that there is no oil on the bolt threads.




g.

Fully tighten the bolts in: Area 1 and Area 2.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


h.

Fully tighten the bolts and nuts in: Area 3.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:

Tighten the bolts and nuts from top to bottom as shown in the illustration.



i.

Fully tighten the bolts in: Area 4.

Torque:
Bolt A : 43 N*m (438 kgf*cm, 32 ft.*lbf)
Except bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:

Tighten the bolts from bottom to top as shown in the illustration.



Hide 11201 7.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 1)

Hide 11201 8.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 2)

Hide 13.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE