Home › Drivetrain › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM › from 2016.05
RM24M0E _52 Drivetrain _059557 TIRE AND WHEEL _0291871 TIRE PRESSURE WARNING SYSTEM D

TIRE AND WHEEL  TIRE PRESSURE WARNING SYSTEM  INITIALIZATION  


NOTICE:
·

Initialization can be confirmed through the tire pressure warning light.

·

The order in which the data is received is random.

·

If the signals from all the tire pressure warning valve and transmitters are received, initialization is completed.

·

Initialization is completed when the Data List "ID Tire Inflation Pressure" display shows the correct pressures (See page Drivetrain>TIRE AND WHEEL>TIRE PRESSURE WARNING SYSTEM>DATA LIST / ACTIVE TEST).

·

Initialization is normally completed within a few minutes.

·

It may take a few minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2124/24 (C2125/25: w/ Full Size Spare Tire) (See page Drivetrain>TIRE AND WHEEL>TIRE PRESSURE WARNING SYSTEM>C2121/21).

·

If initialization has not been completed successfully, DTC C2177/77 is stored after a vehicle speed of 40 km/h (25 mph) or more continues for 20 minutes or more.

·

During test mode (sensor check mode), the system will not change to initialization mode even if the tire pressure warning reset switch is pushed.

·
C217594E05
0.154,0.084 0.828,0.370 0.674,0.286 10 *a 1.964,1.792 2.481,1.971 0.517,0.179 10 TC 1.202,1.792 1.552,1.971 0.350,0.179 10 CG 1.805,1.424 2.049,1.764 false 1.571,1.024 1.366,1.761 false

Initialization can be terminated by connecting terminals 13 (TC) and 4 (CG) of the DLC3.



Text in Illustration
*a Front view of DLC3

BEFORE INITIALIZATION


a.

Make sure that the tires are cool.


b.

Set the tire pressure to the specified value (See page Drivetrain>TIRE AND WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION).



INITIALIZATION PROCEDURE


a.

Turn the engine switch on (IG).


b.
C358260E01
1.829,0.039 1.985,0.221 0.156,0.181 10 *1 0.485,0.039 0.641,0.221 0.156,0.181 10 *2 0.154,3.275 0.310,3.456 0.156,0.181 10 *a 2.16,3.349 2.315,3.531 0.156,0.181 10 *b 0.579,3.67 0.735,3.851 0.156,0.181 10 *c 0.584,3.899 0.740,4.081 0.156,0.181 10 *d 1.922,4.263 2.078,4.444 0.156,0.181 10 *b

Press and hold the tire pressure warning reset switch for 3 seconds or more so that the tire pressure warning light blinks 3 times.

Text in Illustration
*1 Tire Pressure Warning Light
*2 Tire Pressure Warning Reset Switch
*a Tire Pressure Warning Light Output Pattern
*b 1 sec.
*c ON
*d OFF


c.

Turn the engine switch off.


d.

Connect the GTS to the DLC3.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


g.

Check that initialization has been completed.


h.

Confirm that the tire pressure data of all tires is displayed on the GTS screen.