Home › Drivetrain › TIRE AND WHEEL › TIRE AND WHEEL SYSTEM › from 2016.05
RM24M0E _52 Drivetrain _059557 TIRE AND WHEEL _0291867 TIRE AND WHEEL SYSTEM G

TIRE AND WHEEL  TIRE AND WHEEL SYSTEM  INSPECTION  


PROCEDURE

Hide 1.INSPECT TIRES

a.

Check the tires for wear and proper inflation pressure.

Cold tire inflation pressure:
Tire size Front
kPa (kgf/cm2, psi)
Rear
kPa (kgf/cm2, psi)
205/65R16 95H 5 passengers or less 230 (2.3, 33)*1
280 (2.8, 41)*2
6 passengers or more 230 (2.3, 33)*1
280 (2.8, 41)*2
250 (2.5, 36)*1
280 (2.8, 41)*2
215/55R17 94V 5 passengers or less 240 (2.4, 35)*1
280 (2.8, 41)*2
6 passengers or more 240 (2.4, 35)*1
280 (2.8, 41)*2
250 (2.5, 36)*1
280 (2.8, 41)*2


*1: For driving under 160 km/h (100 mph)

*2: For driving at 160 km/h (100 mph) or over

i.

Perform initialization (w/ Tire Pressure Warning System:) (See page Drivetrain>TIRE AND WHEEL>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION).


ii.

Tire pressure adjustment method when warm (w/ Tire Pressure Warning System:).

1.

Turn the engine switch off.

2.

Connect the GTS to the DLC3.

3.

Turn the engine switch on (IG).

4.

Turn the GTS on.

5.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

6.

Adjust the tire pressure so that the displayed value is equal to the set pressure.

7.

Perform initialization and check that initialization completes (See page Drivetrain>TIRE AND WHEEL>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION).

8.

Check and record the value of the Data List item "Temperature in Tire". (Ts)

9.

Check and record the ambient temperature during tire pressure adjustment. (Tm)

10.

Readjust the tire pressure according to the difference between the tire internal temperature (Ts) and the ambient temperature (Tm). (P)

HINT:

Tire internal temperature: Ts, Ambient temperature: Tm, Tire pressure readjustment value: P

P = (Specified Pressure) + (Ts - Tm)


11.

Check the pressure adjustment value with the Data List item "Tire Inflation Pressure".


NOTICE:

for ECE-R64 Type:

If the tire pressure is decreased approximately 20 kPa (0.2 kgf/cm2, 2.9 psi) or more in order to adjust the tire pressure, even if the adjusted tire pressure is 80% or more than the tire pressure set during system initialization, the tire pressure warning light may illuminate if the tire pressure drops below 80% of the tire pressure set when the tires are warmed. In this case, perform initialization again.




b.
C137874

Using a dial indicator, check the runout of the tires.

Maximum Tire Runout:

1.4 mm (0.0551 in.)


HINT:

Measure the runout with the wheel assembly removed from the vehicle.



Hide 2. ROTATE TIRES

a.
C142114E03
2.701,0.435 2.811,0.595 0.110,0.160 10 A 2.701,1.447 2.811,1.607 0.110,0.160 10 B

If the spare tire uses a different type of wheel from the other tires, rotate the tires as shown by (A) in the illustration. If the spare tire has the same type of wheel as the other tires, rotate the tires, including the spare tire, as shown by (B) in the illustration.

Text in Illustration
V100135

Front


b.

w/ Tire Pressure Warning System:



Hide 3.INSPECT WHEEL BALANCE

a.

Inspect and adjust the off-the-car balance.

i.

Steel wheel:

Maximum Wheel Imbalance:

8.0 g (0.0176 lb)



ii.
C144018E24
2.063,3.646 2.354,3.885 0.292,0.24 10 false *a

Others (Non-steel wheel):

Text in Illustration
*a 25 mm (0.984 in.)

Maximum Wheel Imbalance:

8.0 g (0.0176 lb)


NOTICE:
·

Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.

·

Do not touch the adhesive surface of the balance weight.

·

Adhere a stick-on type balance weight to the flat surface*a shown in the illustration.

·

Push the balance weight with your finger to securely adhere it to the desired position.

·

Do not reuse balance weights.



HINT:
·

Use clip-on type balance weights for the inner side, and stick-on type balance weights for the outer side.

·

If the tires vibrate even after the off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.





Hide 4.INSPECT FRONT AXLE HUB

Hide 5.INSPECT REAR AXLE HUB