Home › Brake › BRAKE › BRAKE MASTER CYLINDER(for RHD) › from 2016.05
RM24M0E _54 Brake _059558 BRAKE _0291876 BRAKE MASTER CYLINDER(for RHD) A

BRAKE  BRAKE MASTER CYLINDER(for RHD)  INSTALLATION  


PROCEDURE

Hide 47201 1.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY

NOTICE:
·

The master cylinder and piston are designed so that the piston can easily fall out. Prevent this by making sure that the tip of the master cylinder points downward when handling the master cylinder.

·

Make sure foreign matter does not attach to the master cylinder's piston. If foreign matter attaches, clean it off with a cloth. Then apply lithium soap base glycol grease to the entire outer circumference contact surface area of the piston.



a.

Install a new O-ring to the master cylinder.


b.
C133372E02
2.156,1.02 2.312,1.169 0.156,0.149 10 A 1.831,1.215 1.987,1.364 0.156,0.149 10 A

Install the master cylinder to the booster with the 2 nuts (labeled A).

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


c.
C312988E02
1.75,2.708 2.021,2.938 0.271,0.229 10 false *a 0.917,1.365 1.063,1.542 0.146,0.177 10 false B 1.719,1.094 1.865,1.271 0.146,0.177 10 true B 0.865,0.344 1.01,0.521 0.146,0.177 10 false C

Using a union nut wrench, connect the 2 brake lines (labeled B) to the master cylinder.

Text in Illustration
*a Torque Wrench Fulcrum Length

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length for the torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 250 mm (9.84 in.)):

18 N*m (184 kgf*cm, 13 ft.*lbf)




d.

Connect the No. 1 reservoir tube (labeled C) to the master cylinder.


Hide 44781D 2.INSTALL RESERVOIR HOSE BRACKET

a.

Install the bracket with the nut.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


b.

Install the No. 1 reservoir tube to the clamps of the bracket.


Hide 47202 3.INSTALL BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

a.
C367594E01
2.823,0.292 3.135,0.49 0.313,0.198 10 false F 2.865,1.354 3.177,1.552 0.313,0.198 10 false A 2.823,1.885 3.135,2.083 0.313,0.198 10 false H 2.729,2.427 3.042,2.625 0.313,0.198 10 false D 2.865,3.708 3.177,3.906 0.313,0.198 10 false G 2.177,4.469 2.49,4.667 0.313,0.198 10 false C 1.354,4.365 1.667,4.563 0.313,0.198 10 false B 0.125,4.229 0.438,4.427 0.313,0.198 10 false E 0.208,2.563 0.521,2.76 0.313,0.198 10 false E 1.583,2.063 1.896,2.26 0.313,0.198 10 false G

Install the nut (labeled A) to the reservoir.


b.

Install the reservoir to the reservoir bracket (labeled B) with the bolt (labeled C).

Torque:
8.8 N*m (90 kgf*cm, 78 in.*lbf)


c.

Install the reservoir bracket (labeled D) to the reservoir with bracket with the 2 nuts (labeled E).

Torque:
8.8 N*m (90 kgf*cm, 78 in.*lbf)


d.

Connect the No. 1 reservoir tube (labeled F) to the reservoir.


e.

Install the reservoir with brackets with the 2 nuts (labeled G).

Torque:
8.8 N*m (90 kgf*cm, 78 in.*lbf)


f.

Connect the brake fluid level warning switch connector (labeled H) to the reservoir.


Hide 4.BLEED BRAKE SYSTEM