Home › Brake › BRAKE › FRONT BRAKE(for 16 inch Front Disc Brake)
RM24M0E _54 Brake _059558 BRAKE _0291877 FRONT BRAKE(for 16 inch Front Disc Brake) A

BRAKE  FRONT BRAKE(for 16 inch Front Disc Brake)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the LH side and RH side.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 43512 1.INSTALL FRONT DISC

a.
C133404E01
2.557,0.162 3.289,0.318 0.732,0.156 10 Matchmark 1.741,1.021 2.488,0.299 2.488,0.299 1.758,1.159 false

Align the matchmarks and install the disc.

HINT:

When replacing the disc with a new one, select the installation position where the disc has the minimum runout.



Hide 47547B 3.TEMPORARILY TIGHTEN FRONT DISC BRAKE BLEEDER PLUG

a.

Install the bleeder plug to the cylinder.

HINT:

The bleeder plug will be tightened to a torque specification in the "BLEED AIR FROM BRAKE LINE" procedures.



b.

Install the bleeder plug cap.


Hide 4.INSTALL PISTON SEAL

a.

Apply lithium soap base glycol grease to a new seal.


b.

Install the seal to the cylinder.

NOTICE:

Securely install the piston seal into the groove of the disc brake cylinder.



Hide 47731 5.INSTALL FRONT DISC BRAKE PISTON

a.
C136944E02
0.771,1.031 0.938,0.385 0.938,0.385 1.177,0.385 false 0.76,2.083 0.865,2.354 0.865,2.354 1.021,2.354 false 1.25,0.302 2.167,0.5 0.917,0.198 10 false Cylinder Boot 1.094,2.281 1.573,2.469 0.479,0.188 10 false Piston 0.656,2.938 2.802,3.104 2.146,0.167 10 false Lithium Soap Base Glycol Grease

Apply lithium soap base glycol grease to the piston and a new cylinder boot.


b.

Install the boot to the piston.


c.

Install the piston (with boot) to the cylinder.

NOTICE:

Do not forcibly install the piston to the cylinder.



Hide 6.INSTALL CYLINDER BOOT

a.
C136945E02
0.615,1.906 0.49,2.188 false 1.052,1.927 1.313,2.521 false 0.75,1.292 0.958,0.521 0.958,0.521 1.156,0.521 false 0.167,2.24 0.802,2.427 0.635,0.188 10 false Cylinder 1.104,2.552 1.573,2.729 0.469,0.177 10 false Piston 1.24,0.438 2.167,0.604 0.927,0.167 10 false Cylinder Boot

Install the cylinder boot to the cylinder.

NOTICE:

Securely install the cylinder boot into the groove of the disc brake cylinder.



Hide 47775 7.INSTALL FRONT DISC BRAKE BUSH DUST BOOT

a.
C136946E01
0.563,2.875 2.726,3.059 2.163,0.184 10 Lithium Soap Base Glycol Grease

Apply lithium soap base glycol grease to 2 new boots.


b.

Install the 2 boots to the mounting.


Hide 47715A 8.INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN

a.
C136947E02
1.573,0.708 1.229,0.708 1.229,0.708 1.031,0.885 false 1.594,1.729 1.198,1.729 1.198,1.729 1,1.917 false 2.604,2.354 2.375,2.354 false 0.302,0.906 1.51,1.115 1.208,0.208 10 false Slide Pin (Upper) 0.323,1.948 1.531,2.156 1.208,0.208 10 false Slide Pin (Lower) 1.667,2.281 2.417,2.458 0.75,0.177 10 false Slide Bush 0.542,2.938 2.75,3.115 2.208,0.177 10 false Lithium Soap Base Glycol Grease

Apply lithium soap base glycol grease to the pins and a new bush as shown in the illustration.


b.

Install the bush to the pin (lower).


c.
C136938

Install the 2 pins (upper and lower) to the mounting.


Hide 47722 9.INSTALL FRONT DISC BRAKE CYLINDER MOUNTING LH

a.
C136937

Install the cylinder mounting with the 2 bolts.

Torque:
98 N*m (999 kgf*cm, 72 ft.*lbf)


Hide 47716 10.INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE

a.

Install the 2 plates to the mounting, following the identification tags or marks.

NOTICE:

Install the 2 plates in the correct positions and direction.



Hide 47771 11.INSTALL NO. 1 PAD WEAR INDICATOR PLATE

a.

Install the indicator plate to the upper side of the inner pad.


Hide 04945 12.INSTALL ANTI-SQUEAL SHIM KIT FRONT

a.
i.
U189059E02
0.688,0.625 0.688,0.156 0.688,0.156 0.979,0.156 false 0.938,1.698 0.938,2.104 false 1.906,2.635 2.198,2.635 2.198,2.635 2.375,2.469 false 1.042,0.073 2.979,0.292 1.938,0.219 10 false No. 2 Anti-squeal Shim (Inner) 1.177,0.458 3.094,0.677 1.917,0.219 10 false No. 2 Anti-squeal Shim (Outer) 0.104,2.125 1.573,2.313 1.469,0.188 10 false No. 1 Anti-squeal Shim 0.417,2.542 1.896,2.729 1.479,0.188 10 false No. 1 Anti-squeal Shim 0.677,2.906 1.927,3.104 1.25,0.198 10 false Disc Brake Grease

Apply disc brake grease to both sides of each No. 1 shim.


ii.

Install the No. 1 and No. 2 shims to each pad.

NOTICE:
·

When replacing a worn pad, the shims must be replaced together with the pads.

·

Install the shims in the correct positions and direction as shown in the illustration.





Hide 04465 13.INSTALL FRONT DISC BRAKE PAD

a.

Install the 2 disc brake pads to the mounting.

NOTICE:

There should be no oil or grease on the friction surface of the pads and disc.