Home › Brake › BRAKE › FRONT BRAKE(for 17 inch Front Disc Brake) › from 2016.05
RM24M0E _54 Brake _059558 BRAKE _0291884 FRONT BRAKE(for 17 inch Front Disc Brake) A

BRAKE  FRONT BRAKE(for 17 inch Front Disc Brake)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43512 1.INSTALL FRONT DISC

a.
C356424E01
1.967,1.14 2.35,0.757 2.35,0.757 2.428,0.757 false 1.985,1.188 2.35,0.757 false 2.461,0.662 2.723,0.862 0.262,0.200 10 *a

Align the matchmarks of the front disc and front axle hub sub-assembly, and install the front disc.

Text in Illustration
*a Matchmark

NOTICE:

When replacing the front disc with a new one, select the installation position where the front disc has minimal runout.



Hide 47722 2.INSTALL FRONT DISC BRAKE CYLINDER MOUNTING

a.

Install the front disc brake cylinder mounting to the steering knuckle with the 2 bolts.

Torque:
107 N*m (1089 kgf*cm, 79 ft.*lbf)


Hide 47775 3.INSTALL FRONT DISC BRAKE BUSHING DUST BOOT

a.
C356407

Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new front disc brake bushing dust boots.

Text in Illustration
V100155

Lithium Soap Base Glycol Grease

HINT:

Apply more than 0.3 g (0.01 oz) of lithium soap base glycol grease to each front disc brake bushing dust boot.



b.
C356426

Install the 2 front disc brake bushing dust boots to the front disc brake cylinder mounting.


Hide 47715A 4.INSTALL FRONT NO. 1 DISC BRAKE CYLINDER SLIDE PIN

a.
C190886

Apply a light layer of lithium soap base glycol grease to the contact surface of the front No. 1 disc brake cylinder slide pin.

Text in Illustration
V100155

Lithium Soap Base Glycol Grease


b.
C356427

Install the front No. 1 disc brake cylinder slide pin to the front disc brake cylinder mounting.


c.

Push the front No. 1 disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.


Hide 47769 5.INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSHING

a.
C356408

Apply a light layer of lithium soap base glycol grease to the contact surface of the front No. 2 disc brake cylinder slide pin.

Text in Illustration
V100155

Lithium Soap Base Glycol Grease


b.

Install a new front disc brake cylinder slide bushing to the front No. 2 disc brake cylinder slide pin.


Hide 47715D 6.INSTALL FRONT NO. 2 DISC BRAKE CYLINDER SLIDE PIN

a.
C190883

Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surface of the front No. 2 disc brake cylinder slide pin.

Text in Illustration
V100155

Lithium Soap Base Glycol Grease


b.
C356428

Install the front No. 2 disc brake cylinder slide pin to the front disc brake cylinder mounting.


c.

Push the front No. 2 disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.


Hide 47716 7.INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE

a.
C356429E02
2.365,0.719 2.656,0.719 false 1.135,0.719 0.854,0.719 false 2.385,3.906 2.604,3.906 false 1.135,3.906 0.885,3.906 false 0.708,3.823 1.063,4.094 0.354,0.271 10 false *1 2.635,3.823 2.99,4.094 0.354,0.271 10 false *2 2.688,0.635 3.042,0.906 0.354,0.271 10 false *3 0.667,0.625 1.021,0.896 0.354,0.271 10 false *4

Install the 4 front disc brake pad support plates to the front disc brake cylinder mounting as shown in the illustration.

Text in Illustration
*1 Front No. 1 Disc Brake Pad Support Plate
*2 Front No. 2 Disc Brake Pad Support Plate
*3 Front No. 3 Disc Brake Pad Support Plate
*4 Front No. 4 Disc Brake Pad Support Plate

NOTICE:

Be sure to install each front disc brake pad support plate in the correct position and direction.


HINT:

The front disc brake pad support plate (lower) has a convex part.



Hide 47771 8.INSTALL PAD WEAR INDICATOR PLATE

a.
C204552

Install the front disc brake pad wear indicator plate to each front disc brake pad.

NOTICE:

Install the pad wear indicator plates in the correct positions and directions.



Hide 04945 9.INSTALL FRONT ANTI-SQUEAL SHIM

NOTICE:
·

When replacing worn front disc brake pads, the front disc brake anti-squeal shims and front disc brake pad wear indicator plates must be replaced together with the front disc brake pads.

·

Install the front disc brake pad wear indicator plates in the correct position and direction.

·

Install the front disc brake anti-squeal shims in the correct position and direction.

·

Do not apply disc brake grease to the lining surface of the brake pad.



a.
C170051

Apply disc brake grease to the inside of each front disc brake anti-squeal shim as shown in the illustration.

Text in Illustration
V100155

Disc Brake Grease


b.
C201769

Install the 2 front anti-squeal shims to the front disc brake pads.


Hide 04465 10.INSTALL FRONT DISC BRAKE PAD

a.

Install the 2 front disc brake pads to the front disc brake cylinder mounting.

NOTICE:
·

Keep the friction surfaces of the front disc brake pads and front disc free from oil and grease.

·

Install the front disc brake pad so that the pad wear indicator plate is mounted on the upper side of the vehicle.




b.
C169222

Install the 2 anti-squeal springs to the front disc brake pads.

NOTICE:
·

When replacing the front disc brake pads with new ones, make sure to replace the anti-squeal springs at the same time.

·

Be sure to install the anti-squeal springs into the front disc brake pad installation holes as far as they will go.




Hide 47750 11.INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY

a.

Hold each front disc brake cylinder slide pin and install the front disc brake cylinder assembly to the front disc brake cylinder mounting with the 2 bolts.

Torque:
34 N*m (350 kgf*cm, 25 ft.*lbf)

NOTICE:
·

Install the front disc brake cylinder assembly while holding both of the front disc brake pads because the anti-squeal springs may fall off the front disc brake pads.

·

Be sure that the anti-squeal springs are installed to the front disc brake pads.




Hide 47313A 12.CONNECT FRONT FLEXIBLE HOSE

a.

Connect the front flexible hose to the front disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the front flexible hose lock securely into the lock hole in the front disc brake cylinder assembly.



Hide 13.BLEED BRAKE LINE

Hide 14.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)