Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM
RM24M0E _55 Steering _059560 STEERING COLUMN _0291889 STEERING LOCK SYSTEM C

STEERING COLUMN  STEERING LOCK SYSTEM  B2782  Power Source Control ECU Malfunction  


DESCRIPTION

The steering lock ECU activates the steering lock motor by the power from the main body ECU through the IGE circuit. This prevents the steering from being locked while the vehicle is moving.

The diagnosis information of the steering lock ECU is transmitted to the tester via the certification ECU as the steering lock ECU is not connected to the CAN communication system.

DTC No. DTC Detection Condition Trouble Area
B2782 IGE power supply circuit malfunction
·

Steering lock actuator (Steering lock ECU)

·

Wire harness

·

Main body ECU



WIRING DIAGRAM

C139157E02
6.25,1.938 6.667,3.365 false 0.656,2.729 1.677,2.917 1.021,0.188 10 false Main Body ECU 1.396,0.885 1.771,1.042 0.375,0.156 10 false SLR+ 3.469,2.677 6.26,3.125 2.792,0.448 10 false G32 4.448,0.875 4.76,1.021 0.313,0.146 10 false IGE 4.448,1.427 4.927,1.594 0.479,0.167 10 false SGND 4.469,1.979 4.854,2.125 0.385,0.146 10 false GND 5.792,3.396 7.083,3.573 1.292,0.177 10 false Steering Lock Motor 1.906,0.698 2.094,0.844 0.188,0.146 10 false 19 4.208,0.729 4.417,0.938 0.208,0.208 10 false 3 4.208,1.333 4.479,1.552 0.271,0.219 10 false 2 4.208,1.823 4.417,2.031 0.208,0.208 10 false 1 1.844,0.885 2.146,1.052 0.302,0.167 10 false G57 1.885,1.969 2.135,2.115 0.25,0.146 10 false 4A 1.938,1.781 2.083,1.927 0.146,0.146 10 false 3 3.458,2.844 6.25,3.292 2.792,0.448 10 false Steering Lock Actuator (Steering Lock ECU)

CAUTION / NOTICE / HINT

HINT:

When the ignition switch is off, the main body ECU may occasionally go into a non-active state called sleep mode. Therefore, before proceeding with the inspection, it is necessary to perform the following step to wake up the ECU:

Before starting the inspection, with the ignition switch off, open the driver door. Then (with the ignition switch still off) open and close any door several times at 1.5 second intervals.


PROCEDURE

1.CHECK DTC (CERTIFICATION ECU)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and press the intelligent tester main switch ON.


c.

Read the DTCs of the certification ECU by following the prompts displayed on the intelligent tester.

OK:

DTC B2782 is output, but DTC B2785 (LIN bus line malfunction) is not output.




OK

2.CHECK STEERING LOCK ACTUATOR (IGE VOLTAGE)

NG

GO TO DTC CHART (B2785)

2.CHECK STEERING LOCK ACTUATOR (IGE VOLTAGE)
U188604E02
1.896,1.5 0.573,2.469 false 2.198,1.51 2.771,2.469 false 0.313,2.448 0.885,2.677 0.573,0.229 10 false IGE 2.625,2.5 3.083,2.74 0.458,0.24 10 false SGND 1.542,0.365 1.823,0.635 0.281,0.271 10 false G32

a.

Measure the voltage of the steering lock actuator.

Standard voltage:
Tester Connection Condition Specified Condition
G32-3 (IGE) - G32-2 (SGND) Turn ignition switch on (IG)
(When steering lock motor is activating)
Below 1 V
Ignition switch on (IG)
(When steering lock motor is stopped)
10 to 14 V


HINT:

When the steering lock is activated and the ignition switch is turned on (IG), the steering lock motor activates to release the steering lock. The motor operation occurs for 2 to 15 seconds.




NG

3.CHECK WIRE HARNESS (STEERING LOCK ACTUATOR - BODY GROUND)

OK

REPLACE STEERING LOCK ACTUATOR

3.CHECK WIRE HARNESS (STEERING LOCK ACTUATOR - BODY GROUND)
U188959E01
0.153,0.12 1.462,0.318 1.309,0.198 10 Wire Harness Side: 1.078,1.792 1.526,1.948 0.448,0.156 10 SGND 1.355,1.302 1.348,1.774 false 0.387,1.018 0.799,1.271 0.413,0.253 10 G32

a.

Disconnect the G32 steering lock actuator connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
G32-2 (SGND) - Body ground Below 1 Ω




OK

4.CHECK WIRE HARNESS (STEERING LOCK ACTUATOR - MAIN BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WIRE HARNESS (STEERING LOCK ACTUATOR - MAIN BODY ECU)
U188602E02
1.5,3.646 0.594,3.896 false 1.188,1.896 0.75,1.917 false 0.115,0.094 1.51,0.365 1.396,0.271 10 false Wire Harness Side: 1.198,2.208 2.354,2.448 1.156,0.24 10 false Main Body ECU 1.542,2.823 2.063,3.083 0.521,0.26 10 false G32 1.583,0.604 2.104,0.865 0.521,0.26 10 false G57 1,4.167 2.49,4.448 1.49,0.281 10 false Steering Lock Actuator 0.281,1.844 0.74,2.083 0.458,0.24 10 false SLR+ 0.302,3.844 0.958,4.115 0.656,0.271 10 false IGE

a.

Disconnect the G57 main body ECU connector.


b.

Disconnect the G32 steering lock actuator connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G32-3 (IGE) - G57-19 (SLR+) Below 1 Ω
G32-3 (IGE) or G57-19 (SLR+) - Body ground 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR