Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM
RM24M0E _55 Steering _059560 STEERING COLUMN _0291889 STEERING LOCK SYSTEM J

STEERING COLUMN  STEERING LOCK SYSTEM  Steering Lock Motor Drive Power Circuit  


DESCRIPTION

The main body ECU supplies the power to activate the motor of the steering lock actuator.

The diagnosis information of the steering lock ECU is transmitted to the tester via the certification ECU as the steering lock ECU is not connected to the CAN communication system.

WIRING DIAGRAM

C136914E03
6.302,1.917 6.677,3.313 false 0.656,2.781 1.698,2.99 1.042,0.208 10 false Main Body ECU 1.396,0.885 1.823,1.031 0.427,0.146 10 false SLR+ 4.458,0.885 4.76,1.052 0.302,0.167 10 false IGE 4.458,0.51 4.688,0.729 0.229,0.219 10 false B 4.458,1.469 4.906,1.625 0.448,0.156 10 false SGND 4.479,1.979 4.823,2.125 0.344,0.146 10 false GND 4.25,2.708 5.729,3.26 1.479,0.552 10 false G32 5.823,3.375 7.094,3.542 1.271,0.167 10 false Steering Lock Motor 2.542,0.531 3.333,0.698 0.792,0.167 10 false from Battery 4.229,1.844 4.427,2.042 0.198,0.198 10 false 1 4.229,1.302 4.406,1.479 0.177,0.177 10 false 2 4.24,0.76 4.448,0.979 0.208,0.219 10 false 3 4.229,0.396 4.438,0.604 0.208,0.208 10 false 7 1.896,0.708 2.115,0.854 0.219,0.146 10 false 19 1.854,0.885 2.156,1.063 0.302,0.177 10 false G57 1.885,1.969 2.104,2.115 0.219,0.146 10 false 4A 1.948,1.792 2.052,1.938 0.104,0.146 10 false 3 1.365,1.969 1.802,2.146 0.438,0.177 10 false GND2 4.25,2.885 5.729,3.438 1.479,0.552 10 false Steering Lock Actuator (Steering Lock ECU)

CAUTION / NOTICE / HINT

HINT:

When the ignition switch is off, the main body ECU may occasionally go into a non-active state called sleep mode. Therefore, before proceeding with the inspection, it is necessary to perform the following step to wake up the ECU:

Before starting the inspection, with the ignition switch off, open the driver door. Then (with the ignition switch still off) open and close any door several times at 1.5 second intervals.


NOTICE:

If the steering lock actuator (steering lock ECU) is replaced, with the ignition switch off and the shift lever on P, open and close the driver side door to record the current lock position into the steering lock ECU. If this is not performed, the engine may not start.


PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Check the problem symptom of the steering lock system.

Result
Condition Proceed to
Steering lock cannot be released A
Steering cannot be locked B



A

2.READ VALUE USING INTELLIGENT TESTER (CERTIFICATION ECU)

B

6.CHECK STEERING LOCK ACTUATOR (IGE VOLTAGE)
2.READ VALUE USING INTELLIGENT TESTER (CERTIFICATION ECU)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and press the intelligent tester main switch ON.


c.

Select the item "Lock/Unlock Receive" in the Data List within 10 seconds of starting the engine and read the value displayed on the intelligent tester.

Certification ECU
Item Measurement Item / Range (Display) Normal Condition Diagnostic Note
Lock/Unlock Receive Steering lock command reception record / YES or NO YES: Steering lock/unlock signal received
NO: Steering lock/unlock signal not received
-

OK:

YES is displayed on the tester screen.


Result:
Result Proceed to
OK A
NG (2AZ-FE for smart entry and start system) B
NG (for 2GR-FE for smart entry and start system) C
NG (2AZ-FE for push-button start) D
NG (2GR-FE for push-button start) E




A

3.CHECK WIRE HARNESS (STEERING LOCK ACTUATOR - BATTERY AND BODY GROUND)

B

C

D

E

3.CHECK WIRE HARNESS (STEERING LOCK ACTUATOR - BATTERY AND BODY GROUND)
a.

Disconnect the G32 steering lock actuator connector.


U188961E01
0.102,0.069 1.389,0.266 1.288,0.198 10 Wire Harness Side: 1.619,1.783 2.081,1.939 0.461,0.156 10 SGND 0.485,1.68 0.835,1.836 0.350,0.156 10 GND 1.109,1.282 0.731,1.66 false 1.389,1.292 1.883,1.752 false 0.335,1.096 0.643,1.328 0.309,0.232 10 G32 2.874,0.838 3.106,1.112 0.232,0.274 12 B 2.344,1.193 2.805,0.958 false

b.

Measure the resistance and voltage of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
G32-1 (GND) - Body ground Below 1 Ω
G32-2 (SGND) - Body ground Below 1 Ω

Standard voltage:
Tester Connection Specified Condition
G32-7 (B) - Body ground 10 to 14 V




OK

4.CHECK STEERING LOCK ACTUATOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK STEERING LOCK ACTUATOR
U188606E02
1.896,1.5 0.573,2.469 false 2.208,1.51 2.781,2.469 false 0.333,2.458 0.906,2.688 0.573,0.229 10 false IGE 2.604,2.5 3.063,2.74 0.458,0.24 10 false SGND 1.51,0.344 1.792,0.615 0.281,0.271 10 false G32

a.

Immediately after turning the ignition switch on (IG), inspect the voltage between terminals G32-3 (IGE) and G32-2 (SGND) of the steering lock actuator.

Result
Result Proceed to
Measurement is 10 to 14 V, and measurement never becomes 1 V or less A
Immediately after turning ignition switch on (IG), condition that measurement is 1 V or less occurs B



A

5.CHECK WIRE HARNESS (STEERING LOCK ACTUATOR - MAIN BODY ECU)

B

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

5.CHECK WIRE HARNESS (STEERING LOCK ACTUATOR - MAIN BODY ECU)
a.

Disconnect the G57 main body ECU connector.


U188602E02
1.5,3.646 0.594,3.896 false 1.188,1.896 0.75,1.917 false 0.115,0.094 1.51,0.365 1.396,0.271 10 false Wire Harness Side: 1.198,2.208 2.354,2.448 1.156,0.24 10 false Main Body ECU 1.542,2.823 2.063,3.083 0.521,0.26 10 false G32 1.583,0.604 2.104,0.865 0.521,0.26 10 false G57 1,4.167 2.49,4.448 1.49,0.281 10 false Steering Lock Actuator 0.281,1.844 0.74,2.083 0.458,0.24 10 false SLR+ 0.302,3.844 0.958,4.115 0.656,0.271 10 false IGE

b.

Disconnect the G32 steering lock actuator connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G32-3 (IGE) - G57-19 (SLR+) Below 1 Ω
G32-3 (IGE) or G57-19 (SLR+) - Body ground 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK STEERING LOCK ACTUATOR (IGE VOLTAGE)
a.

Shift the shift lever to the P position.


U188604E02
1.896,1.5 0.573,2.469 false 2.198,1.51 2.771,2.469 false 0.313,2.448 0.885,2.677 0.573,0.229 10 false IGE 2.625,2.5 3.083,2.74 0.458,0.24 10 false SGND 1.542,0.365 1.823,0.635 0.281,0.271 10 false G32

b.

Engine switch off position.


c.

Open the driver side door.


d.

Measure the voltage of the steering lock actuator.

Standard voltage:
Tester Connection Condition Specified Condition
G32-3 (IGE) - G32-2 (SGND) When steering lock motor is activating Below 1 V
When steering lock motor is stopped 10 to 14 V




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

7.CHECK WIRE HARNESS (STEERING LOCK ACTUATOR - MAIN BODY ECU)
7.CHECK WIRE HARNESS (STEERING LOCK ACTUATOR - MAIN BODY ECU)
a.

Disconnect the G57 main body ECU connector.


U188602E02
1.5,3.646 0.594,3.896 false 1.188,1.896 0.75,1.917 false 0.115,0.094 1.51,0.365 1.396,0.271 10 false Wire Harness Side: 1.198,2.208 2.354,2.448 1.156,0.24 10 false Main Body ECU 1.542,2.823 2.063,3.083 0.521,0.26 10 false G32 1.583,0.604 2.104,0.865 0.521,0.26 10 false G57 1,4.167 2.49,4.448 1.49,0.281 10 false Steering Lock Actuator 0.281,1.844 0.74,2.083 0.458,0.24 10 false SLR+ 0.302,3.844 0.958,4.115 0.656,0.271 10 false IGE

b.

Disconnect the G32 steering lock actuator connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G32-3 (IGE) - G57-19 (SLR+) Below 1 Ω
G32-3 (IGE) or G57-19 (SLR+) - Body ground 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR