Home › Steering › POWER STEERING › POWER STEERING SYSTEM › 2013.04–2014.09
RM24M0E _55 Steering _059561 POWER STEERING _0291895 POWER STEERING SYSTEM C

POWER STEERING  POWER STEERING SYSTEM  C1551  IG Power Supply Voltage Malfunction  


DESCRIPTION

The power steering ECU distinguishes the ignition switch status as on (IG) or off through the IG power source circuit.

DTC No. DTC Detection Condition Trouble Area
C1551 IG power source circuit malfunction inside ECU
·

RH ECU-IG fuse

·

IG power source circuit

·

Power steering ECU



WIRING DIAGRAM

C137252E04
0.083,0.781 1.281,0.979 1.198,0.198 10 false from RH-IG Relay 1 2.5,0.969 3.781,1.115 1.281,0.146 10 false RH ECU-IG 4.698,0.781 4.875,0.927 0.177,0.146 10 false IG 4.688,1.885 5.125,2.031 0.438,0.146 10 false PGND 4.792,3.104 6.104,3.271 1.313,0.167 10 false Power Steering ECU 4.302,0.792 4.615,0.969 0.313,0.177 10 false G91 4.313,1.896 4.625,2.094 0.313,0.198 10 false A21 4.385,1.688 4.51,1.854 0.125,0.167 10 false 2 4.385,0.583 4.542,0.75 0.156,0.167 10 false 6

CAUTION / NOTICE / HINT

NOTICE:

If the steering column or power steering ECU has been replaced, perform the rotation angle sensor initialization and torque sensor zero point calibration (see page Steering>POWER STEERING>POWER STEERING SYSTEM>CALIBRATION).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (IG POWER SUPPLY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and press the intelligent tester main switch ON.


c.

Select the item "IG power supply" in the Data List and read the value displayed on the intelligent tester.

Power steering ECU
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG power supply IG power supply:
Min.: 0 V
Max.: 20.1531 V
10 to 14 V Ignition switch on (IG)



NG

2.INSPECT FUSE (RH ECU-IG)

OK

CHECK INTERMITTENT PROBLEMS

2.INSPECT FUSE (RH ECU-IG)
a.

Remove the RH ECU-IG fuse from the instrument panel junction block RH.


b.

Measure the resistance of the fuse.

Standard resistance:

Below 1 Ω




OK

3.CHECK WIRE HARNESS (BATTERY - POWER STEERING ECU)

NG

REPLACE FUSE

3.CHECK WIRE HARNESS (BATTERY - POWER STEERING ECU)
a.
C366251E01
1.917,0.667 2.333,0.917 0.417,0.25 2.417,0.667 2.833,0.917 0.417,0.25 2.021,2.771 2.563,2.354 false 1.75,2.323 2.135,2.219 false 0.146,0.125 1.677,0.365 1.531,0.24 10 false Wire Harness Side: 1.333,2.25 1.896,2.49 0.563,0.24 10 false 6 (IG) 1.385,2.708 2.083,2.958 0.698,0.25 10 false 2 (PGND) 1.979,0.698 2.406,0.969 0.427,0.271 10 false G91 2.5,0.698 3.021,0.927 0.521,0.229 10 false A21

Disconnect the A21 and G91 connectors.


b.

Measure the voltage and resistance of the wire harness side connectors.

Standard voltage:
Tester Connection Condition Specified Condition
G91-6 (IG) - Body ground Ignition switch on (IG) 10 to 14 V


Standard resistance:
Tester Connection Specified Condition
A21-2 (PGND) - Body ground Below 1 Ω




OK

REPLACE POWER STEERING ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR