Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM L

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  PRECAUTION  


NOTICE FOR INITIALIZATION


NOTICE:

When disconnecting the cable from the negative (-) battery terminal, initialize the following systems after the cable is reconnected.

System Name See procedure
Power Slide Door System (Click here)
Power Back Door System
Parking Assist Monitor System
Lighting System



IGNITION SWITCH EXPRESSIONS


HINT:

The type of ignition switch used on this model differs according to the specifications of the vehicle. The expressions listed in the table below are used in this section.

Expression Ignition Switch (position) Engine Switch (condition)
Ignition Switch off LOCK Off
Ignition Switch on (IG) ON On
Ignition Switch on (ACC) ACC On (ACC)
Engine Start START Start



CAUTION:
·

The vehicle is equipped with a Supplemental Restraint System (SRS), which consists of a steering pad, front passenger airbag, curtain shield airbag, front seat side airbag, driver side knee airbag, seat belt pretensioner, center airbag sensor, front airbag sensor, side airbag sensor, rear airbag sensor, and floor side airbag sensor. Failure to carry out service procedures in the correct sequence could cause SRS parts to unexpectedly deploy and possibly lead to serious injuries. Furthermore, if a mistake is made when service SRS parts, they may fail to operate when required. Before performing servicing (including installation / removal, inspection and replacement of parts), be sure to read the following precautions.

·

Before starting work, wait at least 90 seconds after the ignition switch is turned off and after the cable of the negative (-) battery terminal is disconnected. (SRS parts are equipped with a backup power source. If work is started within 90 seconds of turning the ignition switch off and disconnecting the cable from the negative (-) battery terminal, SRS parts may deploy.)

·

Do not expose SRS parts directly to hot air or flames.



NOTICE:
·

Malfunction symptoms of SRS parts are difficult to confirm. DTCs are the most important source of information when troubleshooting. During troubleshooting, always confirm DTCs before disconnecting the cable from the negative (-) battery terminal.

·

For minor collisions where SRS parts do not deploy, always inspect the SRS parts.

·

Before repair work, remove airbag sensors as necessary if any kind of impact is likely to occur to an airbag sensor during the operation.

·

Never use SRS parts from another vehicle. When replacing SRS parts, replace them with new ones.

·

Never disassemble or attempt to repair SRS parts.

·

If an SRS part has been dropped, or if there are any cracks, dents or other defects in the case, bracket or connector, replace the SRS part with a new one.

·

Use an ohmmeter/voltmeter with high impedance (10 kΩ/V minimum) for troubleshooting the electrical circuits.

·

Information labels are attached to the periphery of SRS parts. Follow the cautions and instructions on the labels.

·

After work on SRS parts is completed, perform the SRS warning light check (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).

·

When the cable is disconnected from the negative (-) battery terminal, the memory settings of each system will be cleared. Because of this, be sure to write down the settings of each system before starting work. When work is finished, reset the settings of each system as before. Never use a backup power supply from outside the vehicle to avoid erasing the memory in a system.

·

When disconnecting the cable from the negative (-) battery terminal, initialize the following system(s) after the cable is reconnected.



HINT:

In the airbag system, the center airbag sensor, front airbag sensor LH and RH, side airbag sensor LH and RH (for front side and rear side), rear airbag sensor LH and RH, center floor airbag sensor, rear floor airbag sensor are collectively referred to as the airbag sensors.


HANDLING PRECAUTIONS FOR AIRBAG SENSORS


a.

Before starting the following operations, wait for at least 90 seconds after disconnecting the negative (-) terminal cable from the battery:

i.

Replacement of the airbag sensors


ii.

Adjustment of the front/rear doors of the vehicle equipped with the side airbags and curtain shield airbags (fitting adjustment)



b.

When connecting or disconnecting the airbag sensor connectors, ensure that each sensor is installed in the vehicle.


c.

Do not use the airbag sensors which have been dropped during the operation or transportation.


d.

Do not disassemble the airbag sensors.



INSPECTION PROCEDURE FOR VEHICLE INVOLVED IN ACCIDENT


a.

When the airbag has not deployed, confirm the DTCs by checking the SRS warning light. If there is any malfunction in the SRS airbag system, perform troubleshooting.


b.

When any of the airbags have deployed, replace the airbag sensors and check the installation condition.



SRS CONNECTOR


a.

SRS connectors are located as shown in the following illustration.

C135331E05
4.885,5.979 6.302,6.177 1.417,0.198 10 false Center Airbag Sensor 0.354,1.323 1.875,1.469 1.521,0.146 10 false Front Airbag Sensor LH 0.333,2.094 1.906,2.448 1.573,0.354 10 false Driver Side Knee Airbag (Driver Side Squib)*1 0.323,3.656 2.625,4.01 2.302,0.354 10 false Front Passenger Airbag (Front Passenger Side Squib) 0.333,4.49 1.896,4.688 1.563,0.198 10 false Front Airbag Sensor RH 0.354,5.24 0.75,5.396 0.396,0.156 10 false DLC3 0.333,6.063 1.375,6.219 1.042,0.156 10 false Main Body ECU 0.323,2.885 2.719,3.063 2.396,0.177 10 false Steering Pad (Driver Side Squib) 5.583,2.969 6.458,3.156 0.875,0.188 10 false to Other Side 4.865,4.969 4.969,5.156 0.104,0.188 10 false 1 4.875,4.813 4.979,5 0.104,0.188 10 false 2 5.656,4.823 5.76,5.01 0.104,0.188 10 false 4 6.271,4.823 6.375,5.01 0.104,0.188 10 false 4 5.656,4.958 5.76,5.146 0.104,0.188 10 false 3 6.271,4.958 6.375,5.146 0.104,0.188 10 false 3 3.469,2.844 4.281,3.042 0.813,0.198 10 false Spiral Cable 4.385,2.781 4.604,2.969 0.219,0.188 10 false 12 3.896,3.646 4.115,3.833 0.219,0.188 10 false 14 3.635,4.083 3.854,4.271 0.219,0.188 10 false 13 4.281,3.375 4.5,3.563 0.219,0.188 10 false 11 2.948,1.25 3.167,1.438 0.219,0.188 10 false 6 2.854,1.792 3.073,1.979 0.219,0.188 10 false 5 2.938,4.406 3.156,4.594 0.219,0.188 10 false 6 2.844,4.938 3.063,5.125 0.219,0.188 10 false 5 2.938,5.208 3.156,5.396 0.219,0.188 10 false 20 2.823,5.719 3.042,5.906 0.219,0.188 10 false 19 2.917,5.969 3.135,6.156 0.219,0.188 10 false 18 2.823,6.49 3.042,6.677 0.219,0.188 10 false 17 2.917,2.052 3.135,2.24 0.219,0.188 10 false 16 2.833,2.573 3.052,2.76 0.219,0.188 10 false 15 2.896,2.823 3.115,3.01 0.219,0.188 10 false 10 2.854,3.375 2.969,3.563 0.115,0.188 10 false 9 2.948,3.615 3.063,3.802 0.115,0.188 10 false 8 2.854,4.146 2.969,4.333 0.115,0.188 10 false 7 0.521,7.427 3.365,7.677 2.844,0.25 10 false *1: w/ Side Airbag and Curtain Shield Airbag

C135332E03
4.052,0.25 6.458,0.667 2.406,0.417 10 false Side Airbag Sensor LH*2 / RH*3, *1 4.031,7.135 6.323,7.573 2.292,0.438 10 false Side Airbag Sensor RH*2 / LH*3, *1 4.01,1.198 6.344,1.552 2.333,0.354 10 false Curtain Shield Airbag LH*2 / RH*3 (Driver Side Curtain Shield Squib)*1 3.99,6.104 6.927,6.458 2.938,0.354 10 false Curtain Shield Airbag RH*2 / LH*3 (Front Passenger Side Curtain Shield Squib)*1 4.01,2.167 6.344,2.521 2.333,0.354 10 false Front Seat Side Airbag LH*2 / RH*3 (Driver Side - Side Squib)*1 4.01,5.115 6.854,5.469 2.844,0.354 10 false Front Seat Side Airbag RH*2 / LH*3 (Front Passenger Side - Side Squib)*1 4.01,3.146 6.344,3.5 2.333,0.354 10 false Front Seat Outer Belt LH*2 / RH*3 (Driver Side Pretensioner Squib)*1 4.01,4.146 6.573,4.51 2.563,0.365 10 false Front Seat Outer Belt RH*2 / LH*3 (Front Passenger Side Pretensioner Squib)*1 0.219,7.698 2.99,7.938 2.771,0.24 10 false *1: w/ Side Airbag and Curtain Shield Airbag 0.823,6.729 2.24,6.917 1.417,0.188 10 false Center Airbag Sensor 0.708,6.135 0.896,6.323 0.188,0.188 10 false 1 1.542,6.135 1.729,6.323 0.188,0.188 10 false 3 2.281,6.125 2.469,6.313 0.188,0.188 10 false 3 1.552,5.958 1.74,6.146 0.188,0.188 10 false 4 2.281,5.958 2.469,6.146 0.188,0.188 10 false 4 0.719,5.958 0.906,6.146 0.188,0.188 10 false 2 0.344,4.021 1.219,4.177 0.875,0.156 10 false to Other Side 3.688,0.115 3.875,0.281 0.188,0.167 10 false 22 3.656,1.115 3.844,1.281 0.188,0.167 10 false 24 3.656,2.104 3.844,2.271 0.188,0.167 10 false 26 3.646,3.094 3.833,3.26 0.188,0.167 10 false 28 3.667,5.031 3.854,5.198 0.188,0.167 10 false 26 3.646,6.042 3.833,6.208 0.188,0.167 10 false 24 3.781,0.781 3.969,0.948 0.188,0.167 10 false 21 3.781,1.76 3.969,1.927 0.188,0.167 10 false 23 3.781,2.74 3.969,2.906 0.188,0.167 10 false 25 3.781,3.729 3.969,3.896 0.188,0.167 10 false 27 3.646,4.083 3.833,4.25 0.188,0.167 10 false 28 3.781,4.698 3.969,4.865 0.188,0.167 10 false 27 3.781,5.698 3.969,5.865 0.188,0.167 10 false 25 3.781,6.667 3.969,6.833 0.188,0.167 10 false 23 3.646,7.031 3.833,7.198 0.188,0.167 10 false 22 3.781,7.656 3.969,7.823 0.188,0.167 10 false 21 0.208,8.031 1,8.229 0.792,0.198 10 false *2: for LHD 0.198,8.365 1.01,8.573 0.813,0.208 10 false *3: for RHD

No. Item Application
(1) Terminal Twin-Lock Mechanism Connectors 2, 4, 6, 8, 12, 14, 16, 24, 26
(2) Activation Prevention Mechanism Connectors 2, 4, 7, 9, 11, 13, 25, 27
(3) Half Connection Prevention Mechanism Connectors 6, 8, 12, 13, 22, 26
(4) Connector Position Assurance Mechanism Connector 6
(5) Connector Lock Mechanism (1) Connectors 10, 24, 28
(6) Connector Lock Mechanism (2) Connectors 2, 4
(7) Improper Connection Prevention Lock Mechanism Connectors 1, 3


b.
H045308E08
1.384,0.571 2.017,0.775 0.634,0.205 10 Spacer 0.954,1.607 1.696,1.825 0.742,0.218 10 Housing 1.014,1.392 1.272,1.607 1.272,1.607 1.779,1.186 false 1.16,0.447 1.616,0.576 1.616,0.576 2.286,0.275 false

All connectors in the SRS except the seat position sensor connector and the occupant classification ECU connector are colored yellow to distinguish them from other connectors. Some connectors have special functions, and are specially designed for the SRS. These connectors use durable gold-plated terminals, and are placed in the locations shown on the previous page to ensure high reliability.

i.

Terminal twin-lock mechanism:

Each connector is a two-piece component consisting of a housing and a spacer. This design enables the terminal to be locked securely by two locking devices (the retainer and the lance) to prevent the terminals from becoming disconnected.


ii.

Activation prevention mechanism:

Each connector contains a short spring plate. When the connector is disconnected, the short spring plate creates a short circuit by automatically connecting the positive (+) and negative (-) terminals of the squib.

U186446E03
1.969,1.25 2.302,2.26 false 2.302,2.26 2.042,2.813 false 1.385,2.844 1.25,2.344 false 2.354,3.115 2.354,3.01 false 1.51,3.885 1.563,3.479 false 1.563,3.469 1.635,3.885 false 1.49,4.135 1.604,4.375 false 1.604,4.375 1.656,4.167 false 5.938,1.906 5.385,1.219 false 5.688,2.906 5.802,2.51 false 5,3.865 5,3.5 false 5.458,4.302 5.458,4 false 2.25,4.458 1.729,3.938 false 1.396,0.042 3.417,0.208 2.021,0.167 10 false When Connector is Connected 4.615,0.031 6.969,0.198 2.354,0.167 10 false When Connector is Disconnected 2.365,2.188 3.604,2.375 1.24,0.188 10 false Short Spring Plate 0.708,2.25 1.292,2.438 0.583,0.188 10 false Housing 2.125,3.156 2.708,3.344 0.583,0.188 10 false Housing 1.302,3.24 1.885,3.385 0.583,0.146 10 false Terminal 1.25,4.385 2.167,4.573 0.917,0.188 10 false Connectors 5.604,1.906 6.844,2.094 1.24,0.188 10 false Short Spring Plate 5.458,2.323 7.083,2.5 1.625,0.177 10 false Contacting Male Terminal 4.406,3.25 5.958,3.427 1.552,0.177 10 false Short Spring Plate ON 5.083,4.365 6.042,4.552 0.958,0.188 10 false Closed Circuit 5.667,4.115 6,4.271 0.333,0.156 8 false Squib 2.281,3.563 2.604,3.729 0.323,0.167 8 false Squib 2.094,4.448 3.323,4.677 1.229,0.229 10 false Short Spring Plate


iii.

Half connection prevention mechanism:

If the connector is not completely connected, the connector is disconnected by the spring operation so that no continuity exists.

H101827E15
3.25,0.635 3.448,0.125 false 3.073,0.5 2.917,0.135 false 2.354,0.708 2.219,0.125 false 1.26,0.813 0.969,0.531 false 1.792,0.719 0.969,0.115 false 5.792,0.604 6.135,0.115 false 0.167,0.406 1.031,0.615 0.865,0.208 10 false Locking Part 1.417,0.042 2.24,0.25 0.823,0.208 10 false Locking Arm 2.531,0.052 2.958,0.26 0.427,0.208 10 false Slider 3.479,0.042 3.969,0.25 0.49,0.208 10 false Spring 3.635,1.354 5.552,1.563 1.917,0.208 10 false Rebounded by Slider (Spring) 0.448,0.031 1.042,0.24 0.594,0.208 10 false Stopper 6.177,0.052 6.771,0.26 0.594,0.208 10 false Stopper


iv.

Connector position assurance mechanism:

The CPA (yellow part) slides, which completes the connector engagement, only when the housing lock (white part) is completely engaged.

H101954E11
2.573,0.792 2.083,0.146 false 2.198,1.469 2.042,1.552 false 0.438,0.083 2.271,0.271 1.833,0.188 10 false Housing Lock (White Part) 0.885,1.49 2.125,1.656 1.24,0.167 10 false CPA (Yellow Part)


v.

Connector lock mechanism (1):

Locking the connector lock button connects the connector.

H101828E29
2.177,1.271 1.76,1.271 false 2.24,0.792 1.771,0.792 false 2.74,0.385 3.104,0.385 false 1.448,0.698 1.844,0.875 0.396,0.177 10 false Claw 1.292,1.188 1.875,1.365 0.583,0.177 10 false Groove 3.146,0.313 3.969,0.49 0.823,0.177 10 false Lock Button


vi.

Connector lock mechanism (2):

Both the primary lock with holder lances and the secondary lock with a retainer prevent the connectors from becoming disconnected.

C364462E01
0.865,1.854 1.229,1.49 true 4.448,1.479 4.969,1.667 false 1.365,3.542 1.781,3.198 true 3.938,3.052 4.188,2.802 false 6,2.865 6.167,2.375 false 5.542,2.688 5.813,2.802 false 0.552,1.854 1.323,2.052 0.771,0.198 10 false Lance 0.792,3.458 1.563,3.656 0.771,0.198 10 false Retainer 5.01,1.604 5.781,1.802 0.771,0.198 10 false Holder 5.083,2.563 5.854,2.76 0.771,0.198 10 false Holder 3.604,3.063 4.375,3.26 0.771,0.198 10 false Retainer 5.906,2.188 6.677,2.385 0.771,0.198 10 false Retainer


vii.

Improper connection prevention lock mechanism:

When connecting the holder, the lever is pushed into the end by rotating around the A axis to lock the holder securely.

U135234E05
1.26,1.115 1.26,0.75 false 5.385,0.865 5.021,0.375 false 5.344,1.354 4.49,1.354 false 1.219,0.594 1.385,0.792 0.167,0.198 10 false A 3.49,1.969 3.656,2.167 0.167,0.198 10 false 2 1.729,1.865 1.896,2.063 0.167,0.198 10 false 1 4.906,0.208 5.073,0.406 0.167,0.198 10 false A 4.104,1.26 4.531,1.458 0.427,0.198 10 false Lever




DISCONNECTION OF CONNECTORS FOR STEERING PAD, FRONT PASSENGER AIRBAG ASSEMBLY (SQUIB SIDE), DRIVER SIDE KNEE AIRBAG ASSEMBLY, CURTAIN SHIELD AIRBAG ASSEMBLY AND FRONT SEAT OUTER BELT ASSEMBLY


HINT:

Tape up the screwdriver tip before use.


a.

Release the lock button (yellow part) of the connector using a screwdriver.


b.

Insert the screwdriver tip between the connector and the base, and then raise the connector.

H101832E07
2.118,0.161 3.061,0.548 0.943,0.387 10 Lock Button (Yellow Part) 0.726,0.383 1.007,0.615 0.281,0.231 10 (a) 3.865,0.383 4.099,0.618 0.235,0.235 10 (b) 5.98,0.161 6.923,0.548 0.943,0.387 10 Lock Button (Yellow Part) 2.118,0.385 1.648,0.961 false 5.98,0.338 5.387,0.827 false



CONNECTION OF CONNECTORS FOR STEERING PAD, FRONT PASSENGER AIRBAG ASSEMBLY (SQUIB SIDE), DRIVER SIDE KNEE AIRBAG ASSEMBLY, CURTAIN SHIELD AIRBAG ASSEMBLY AND FRONT SEAT OUTER BELT ASSEMBLY


a.

Connect the connector.


b.

Push the lock button (yellow part) of the connector down securely. (When locking, a click sound can be heard.)

H101833E06
4.919,1.143 5.861,1.543 0.941,0.400 10 Lock Button (Yellow Part) 4.508,1.692 4.857,1.305 false



DISCONNECTION OF CONNECTORS FOR FRONT PASSENGER AIRBAG ASSEMBLY (INSTRUMENT PANEL WIRE SIDE)


a.

Place a finger on the slider, slide the slider to release the lock, and then disconnect the connector.

H101836E23
0.813,0.906 1.479,1.271 false 2.802,0.865 3.385,1.25 false 2.438,0.771 2.854,0.979 0.417,0.208 10 false Slider 0.427,0.813 0.844,1.021 0.417,0.208 10 false Slider 4.667,2.25 6.375,2.458 1.708,0.208 10 false Disconnection complete



CONNECTION OF CONNECTOR FOR FRONT PASSENGER AIRBAG ASSEMBLY (INSTRUMENT PANEL WIRE SIDE)


a.

Connect the connector as shown in the illustration. (When locking, make sure that the slider returns to its original position and a click sound can be heard.)

HINT:

When connecting, the slider sides. Do not touch the slider while connecting, as this may result in an insecure fit.


H101837E09
1.844,1.115 2.51,1.333 false 5.083,1.156 5.677,1.542 false 4.698,1.063 5.115,1.271 0.417,0.208 10 false Slider 1.448,1.031 1.865,1.24 0.417,0.208 10 false Slider 4.74,2.656 6.156,2.865 1.417,0.208 10 false Connection complete



DISCONNECTION OF CONNECTORS FOR FRONT SEAT SIDE AIRBAG ASSEMBLY


a.

Place a finger on the slider, slide the slider to release the lock, and then disconnect the connector.

H101834E04
1.271,1.052 1.885,1.344 false 2.854,1.031 3.469,1.333 false 4.448,2.271 6.208,2.458 1.76,0.188 10 false Disconnection complete 2.458,0.938 2.906,1.125 0.448,0.188 10 false Slider 0.885,0.958 1.333,1.146 0.448,0.188 10 false Slider



CONNECTION OF CONNECTORS FOR FRONT SEAT SIDE AIRBAG ASSEMBLY


a.

Connect the connector as shown in the illustration. (When locking, make sure that the slider returns to its original position and a click sound can be heard.)

HINT:

When connecting, the slider slides. Do not touch the slider while connecting, as this may result in an insecure fit.


H101835E04
1.896,1.188 2.563,1.396 false 5,1.177 5.594,1.573 false 4.625,1.073 5.042,1.281 0.417,0.208 10 false Slider 1.521,1.094 1.938,1.302 0.417,0.208 10 false Slider 4.667,2.677 6.083,2.885 1.417,0.208 10 false Connection complete



DISCONNECTION OF CONNECTOR FOR CENTER AIRBAG SENSOR ASSEMBLY


a.

Pull the lever by pushing part A as shown in the illustration and disconnect the holder (with connectors).

H100822E16
1.125,1.615 1.417,1.323 true 5.344,1.49 4.854,0.698 false 1.448,1.198 1.604,1.375 0.156,0.177 10 false A 3.333,0.615 4.854,0.792 1.521,0.177 10 false Holder (with connectors) 4.438,2.479 6.146,2.656 1.708,0.177 10 false Disconnection is complete

HINT:

Perform the following procedures when replacing the holder.



b.

Remove the holder.

i.

Using a screwdriver, unlock the retainer.

H100823E01
2.471,1.005 3.147,1.187 0.676,0.181 10 Retainer 2.179,1.479 2.428,1.089 false


ii.

Release the fitting lances and remove the holder.

H100824E08
1.425,2.136 1.890,2.317 0.465,0.181 10 Lances 1.405,1.821 1.609,2.136 1.609,2.136 0.981,1.821 false 2.133,1.825 1.615,2.144 false



c.
H100825

Install the holder.

i.

Install the connectors into the holder. (When locking, a click sound can be heard.)

HINT:

The retainer is locked when the holder is connected.





CONNECTION OF CONNECTOR FOR CENTER AIRBAG SENSOR ASSEMBLY


a.

Firmly insert the holder (with connectors) into the center airbag sensor until it cannot be pushed any further.


b.

Push the lever to connect the holder (with connectors). (When locking, a click sound can be heard.)

HINT:

The holder slides into the center airbag sensor when it is being connected. Do not hold the holder while connecting, as it may result in an insecure fit.


H100903E09
3.698,1.521 4.208,1.167 true 0.802,1.302 1.156,0.448 true 1.219,0.354 2.74,0.531 1.521,0.177 10 false Holder (with connectors) 4.271,1.073 4.635,1.25 0.365,0.177 10 false Lever 5.365,2.25 6.906,2.427 1.542,0.177 10 false Connection is complete



DISCONNECTION OF CONNECTORS FOR FRONT AIRBAG SENSOR


a.

Push down the housing lock (white part) and slide the CPA (yellow part). (At this time, the connector cannot be disconnected yet.)


b.

Push down the housing lock (white part) again and disconnect the connector.

HINT:

Do not push down part A shown in the illustration when disconnecting.


H101952E04
5.032,0.766 6.771,0.970 1.739,0.204 10 Housing Lock (White Part) 0.061,1.412 0.895,1.901 0.833,0.489 10 Connector lock is released 4.748,0.413 4.987,0.649 0.239,0.236 10 A 3.235,1.711 4.464,1.913 1.229,0.202 10 CPA (Yellow Part) 4.572,0.973 5.018,0.836 false 4.296,0.724 4.691,0.497 false 0.782,2.438 0.722,1.664 false 3.921,1.384 3.921,1.711 false


c.

After disconnecting the connector, check that the position of the housing lock (white part) is as shown in the illustration.

H101953



CONNECTION OF CONNECTORS FOR FRONT AIRBAG SENSOR


a.

Before connecting the connectors, check that the position of the housing lock (white part) is as shown in the illustration.

H101950


b.

Be sure to engage the connectors until they are locked. (When locking, make sure that a click sound can be heard.)

HINT:

When connecting them, the housing lock (white part) slides. Do not hold the housing lock (white part) and part A, as it may result in an insecure fit.


H101951E07
2.292,0.781 2.729,0.292 false 2.469,0.969 2.969,0.573 false 2.542,1.375 2.542,1.74 false 3.052,0.469 4.802,0.646 1.75,0.177 10 false Housing Lock (White Part) 2,1.75 3.156,1.958 1.156,0.208 10 false CPA (Yellow Part) 5.302,3.365 6.927,3.542 1.625,0.177 10 false Connection is complete 2.802,0.208 2.979,0.385 0.177,0.177 10 false A



DISCONNECTION OF CONNECTORS FOR SIDE AIRBAG SENSOR, REAR AIRBAG SENSOR, AND FLOOR AIRBAG SENSOR


a.
H100826E10
1.391,0.54 0.832,0.352 false 0.351,0.261 0.738,0.425 0.387,0.164 10 Outer

While holding both sides of the outer connector locking sleeve, slide the outer in the direction shown by the arrow.


b.

When the connector lock is released, the connectors are disconnected.

HINT:

Be sure to hold both outer flanks. Holding the top and bottom sides will make disconnection difficult.


H100827E16
2.677,0.677 2.292,0.229 false 0.635,0.146 2.292,0.323 1.656,0.177 10 false Connector lock is released 4.531,1.385 6.24,1.563 1.708,0.177 10 false Disconnection is complete



CONNECTION OF CONNECTORS FOR SIDE AIRBAG SENSOR, REAR AIRBAG SENSOR, AND FLOOR AIRBAG SENSOR


a.

Connect the connector as shown in the illustration (When locking, make sure that the outer returns to its original position and a click sound can be heard).

HINT:

When connecting, the outer slides. Do not hold the outer while connecting, as it may result in an insecure fit.


H100828E23
3.969,0.229 4.052,0.385 false 5.667,0.208 5.885,0.406 false 3.583,0.115 3.948,0.292 0.365,0.177 10 false Outer 5.281,0.115 5.646,0.292 0.365,0.177 10 false Outer 4.646,2.49 6.104,2.667 1.458,0.177 10 false Connection is complete