Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1800/51  Short in Driver Side Squib Circuit  B1801/51  Open in Driver Side Squib Circuit  B1802/51  Short to GND in Driver Side Squib Circuit  B1803/51  Short to B+ in Driver Side Squib Circuit  


DESCRIPTION

The driver side squib circuit consists of the center airbag sensor, the spiral cable and the steering pad.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the driver side squib circuit.


DTC No. DTC Detection Condition Trouble Area
B1800/51 Center airbag sensor receives a line short signal 5 times in the driver side squib circuit during primary check.
·

Instrument panel wire

·

Spiral cable

·

Steering pad (driver side squib)

·

Center airbag sensor


B1801/51 Center airbag sensor receives an open signal in the driver side squib circuit for 2 seconds.
·

Instrument panel wire

·

Spiral cable

·

Steering pad (driver side squib)

·

Center airbag sensor


B1802/51 Center airbag sensor receives a short to ground signal in the driver side squib circuit for 0.5 seconds.
·

Instrument panel wire

·

Spiral cable

·

Steering pad (driver side squib)

·

Center airbag sensor


B1803/51 Center airbag sensor receives a short to B+ signal in the driver side squib circuit for 0.5 seconds.
·

Instrument panel wire

·

Spiral cable

·

Steering pad (driver side squib)

·

Center airbag sensor



WIRING DIAGRAM

C140804E05
0.531,3.573 1.75,3.938 1.219,0.365 10 false Steering Pad (Driver Side Squib) 1.813,3.594 2.625,3.792 0.813,0.198 10 false Spiral Cable 1.281,2.156 1.521,2.323 0.24,0.167 10 false D+ 5.365,2.25 5.604,2.417 0.24,0.167 10 false D+ 2.198,2.167 2.438,2.333 0.24,0.167 10 false D+ 2.5,2.271 2.802,2.438 0.302,0.167 10 false G11 2.594,2.031 2.75,2.198 0.156,0.167 10 false 1 1.635,2.281 1.792,2.448 0.156,0.167 10 false i1 1.646,2.073 1.802,2.24 0.156,0.167 10 false 2 2.5,3.063 2.802,3.229 0.302,0.167 10 false G11 2.583,2.865 2.74,3.031 0.156,0.167 10 false 2 5,2.26 5.302,2.427 0.302,0.167 10 false G19 5.094,2.052 5.25,2.219 0.156,0.167 10 false 5 5,3.052 5.302,3.219 0.302,0.167 10 false G19 5.094,2.865 5.25,3.031 0.156,0.167 10 false 6 1.646,3.073 1.802,3.24 0.156,0.167 10 false i1 1.646,2.885 1.802,3.052 0.156,0.167 10 false 1 5.365,3.052 5.604,3.219 0.24,0.167 10 false D- 2.208,2.979 2.448,3.146 0.24,0.167 10 false D- 1.281,2.958 1.521,3.125 0.24,0.167 10 false D- 5.229,4.094 6.615,4.302 1.385,0.208 10 false Center Airbag Sensor

CAUTION / NOTICE / HINT

HINT:
·

Perform the simulation method by selecting the "Check Mode" (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting the "Check Mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).



PROCEDURE

1.CHECK STEERING PAD (DRIVER SIDE SQUIB)
a.

Turn the ignition switch off.

C364209E02
4.344,0.635 4.76,0.885 0.417,0.25 0.938,1.74 0.802,1.74 0.802,1.74 0.708,1.115 false 5.698,0.76 6,0.76 false 4.292,2.406 4.5,2.042 true 4.729,2.427 4.583,2.208 true 0.813,1.198 1.125,1.396 0.313,0.198 10 false F 0.979,1.198 1.292,1.396 0.313,0.198 10 false E 1.135,1.417 2.01,1.677 0.875,0.26 10 false Spiral Cable 0.979,1.656 2.104,1.948 1.125,0.292 10 false Driver Side Squib 1.906,1.188 2.219,1.385 0.313,0.198 10 false D 2.031,1.188 2.344,1.385 0.313,0.198 10 false C 2.323,1.729 3.448,2.156 1.125,0.427 10 false Center Airbag Sensor 4.938,0.104 6.073,0.365 1.135,0.26 10 false Connector E 6.052,0.677 6.417,0.875 0.365,0.198 10 false SST 4.49,0.677 4.802,0.875 0.313,0.198 10 false i1 4.302,1.573 4.813,1.813 0.51,0.24 10 false DLC3 4.125,2.427 4.438,2.625 0.313,0.198 10 false CG 4.688,2.469 5,2.667 0.313,0.198 10 false TC 5.854,2.458 6.479,2.688 0.625,0.229 10 false DTC 51


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the steering pad.


d.

Connect SST (resistance 2.1 Ω) to connector E.


CAUTION:

Never connect a tester to the steering pad (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting them.

·

Insert straight SST into the terminals of the connector.



SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch on (IG), and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


j.

Check the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1800, B1801, B1802, B1803 or 51 is not output.


HINT:

DTCs other than DTC B1800, B1801, B1802, B1803 or 51 may be output at this time, but they are not related to this check.




NG

2.CHECK CONNECTOR

OK

REPLACE STEERING PAD

2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from the spiral cable.


d.

Check that the spiral cable connectors (on the steering pad side) are not damaged.

OK:

Lock button is not disengaged, and claw of lock is not deformed or damaged.




OK

3.CHECK DRIVER SIDE SQUIB CIRCUIT

NG

REPLACE SPIRAL CABLE

3.CHECK DRIVER SIDE SQUIB CIRCUIT
a.
C114805E05
0.198,0.938 0.354,0.208 0.354,0.208 0.479,0.208 false 1.25,3.135 1.635,3 true 0.771,3 1.125,3.135 true 1.396,3.656 1.531,3.656 false 0.521,0.104 1.667,0.323 1.146,0.219 10 false Driver Side Squib 0.656,1.448 1.469,1.625 0.813,0.177 10 false Spiral Cable 2.344,1.823 3.219,2.156 0.875,0.333 10 false Center Airbag Sensor 0.76,2.469 1.677,2.625 0.917,0.156 10 false Connector E 1.656,2.906 1.896,3.063 0.24,0.156 10 false D+ 0.531,2.917 0.74,3.073 0.208,0.156 10 false D- 1.552,3.573 2.5,3.76 0.948,0.188 10 false Color: Orange 0.271,1.146 0.396,1.292 0.125,0.146 10 false F 0.49,1.135 0.615,1.281 0.125,0.146 10 false E 1.635,1.125 1.771,1.271 0.135,0.146 10 false D 1.781,1.125 1.917,1.281 0.135,0.156 10 false C 2.104,1.125 2.24,1.281 0.135,0.156 10 false B 2.469,0.896 2.604,1.052 0.135,0.156 10 false A

Disconnect the connector from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch on (IG).


d.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
i1-1 (D+) - Body ground Below 1 V
i1-2 (D-) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
i1-1 (D+) - i1-2 (D-) Below 1 Ω
i1-1 (D+) - Body ground 1 MΩ or higher
i1-2 (D-) - Body ground



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
i1-1 (D+) - i1-2 (D-) 1 MΩ or higher




NG

4.CHECK INSTRUMENT PANEL WIRE

OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

4.CHECK INSTRUMENT PANEL WIRE
a.
U188955E02
0.198,1.115 0.271,2.021 0.271,2.021 0.396,2.021 false 1.969,3.667 2.354,3.667 true 2.271,3.323 1.802,3.677 true 1.833,0.188 1.948,0.188 1.948,0.188 2.021,0.99 false 0.438,1.906 1.583,2.125 1.146,0.219 10 false Driver Side Squib 0.083,0.104 1.51,0.26 1.427,0.156 10 false Instrument Panel Wire 0.625,1.5 1.438,1.677 0.813,0.177 10 false Spiral Cable 2.281,1.823 3.177,2.156 0.896,0.333 10 false Center Airbag Sensor 1.25,2.719 2.167,2.875 0.917,0.156 10 false Connector C 0.74,3.542 1.042,3.698 0.302,0.156 10 false G11 2.365,3.583 2.604,3.74 0.24,0.156 10 false D+ 2.302,3.229 2.51,3.385 0.208,0.156 10 false D- 0.292,1.208 0.417,1.354 0.125,0.146 10 false F 0.5,1.208 0.625,1.354 0.125,0.146 10 false E 1.573,1.208 1.708,1.354 0.135,0.146 10 false D 1.781,1.208 1.917,1.365 0.135,0.156 10 false C 2.125,1.208 2.26,1.365 0.135,0.156 10 false B 2.479,0.969 2.615,1.125 0.135,0.156 10 false A

Restore the released activation prevention mechanism of connector B to its original position.


b.

Disconnect the instrument panel wire connector from the spiral cable.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch on (IG).


e.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
G11-1 (D+) - Body ground Below 1 V
G11-2 (D-) - Body ground



f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


h.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
G11-1 (D+) - G11-2 (D-) Below 1 Ω
G11-1 (D+) - Body ground 1 MΩ or higher
G11-2 (D-) - Body ground



i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


j.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
G11-1 (D+) - G11-2 (D-) 1 MΩ or higher




OK

REPLACE SPIRAL CABLE

NG

REPAIR OR REPLACE INSTRUMENT PANEL WIRE