Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1805/52  Short in Front Passenger Side Squib Circuit  B1806/52  Open in Front Passenger Side Squib Circuit  B1807/52  Short to GND in Front Passenger Side Squib Circuit  B1808/52  Short to B+ in Front Passenger Side Squib Circuit  


DESCRIPTION

The front passenger side squib circuit consists of the center airbag sensor and the front passenger airbag.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the front passenger side squib circuit.

DTC No. DTC Detection Condition Trouble Area
B1805/52 Center airbag sensor receives a line short signal 5 times in the front passenger side squib circuit during primary check.
·

Instrument panel wire

·

Instrument panel wire assembly

·

Front passenger airbag (Front passenger side squib)

·

Center airbag sensor


B1806/52 Center airbag sensor receives an open circuit signal in the front passenger side squib circuit for 2 seconds.
·

Instrument panel wire

·

Instrument panel wire assembly

·

Front passenger airbag (Front passenger side squib)

·

Center airbag sensor


B1807/52 Center airbag sensor receives a short to ground signal in the front passenger side squib circuit for 0.5 seconds.
·

Instrument panel wire

·

Instrument panel wire assembly

·

Front passenger airbag (Front passenger side squib)

·

Center airbag sensor


B1808/52 Center airbag sensor receives a short to B+ signal in the front passenger side squib circuit for 0.5 seconds.
·

Instrument panel wire

·

Instrument panel wire assembly

·

Front passenger airbag (Front passenger side squib)

·

Center airbag sensor



WIRING DIAGRAM

C368093E01
5.188,4.135 6.563,4.406 1.375,0.271 10 false Center Airbag Sensor 0.875,3.573 2.354,4 1.479,0.427 10 false Front Passenger Airbag (Passenger Side Squib) 2.198,2.156 2.688,2.417 0.49,0.26 10 false P+ 2.573,2.073 3.063,2.333 0.49,0.26 10 false 2 2.563,2.833 3.052,3.094 0.49,0.26 10 false 1 2.521,2.26 3.01,2.521 0.49,0.26 10 false V1 3.698,2.26 4.188,2.521 0.49,0.26 10 false GV1 4.99,2.25 5.479,2.51 0.49,0.26 10 false G19 5.063,2.052 5.552,2.313 0.49,0.26 10 false 4 5.083,2.854 5.573,3.115 0.49,0.26 10 false 3 2.219,2.958 2.708,3.219 0.49,0.26 10 false P- 5.375,2.25 5.865,2.51 0.49,0.26 10 false P+ 5.354,3.042 5.844,3.302 0.49,0.26 10 false P- 2.531,3.052 3.021,3.313 0.49,0.26 10 false V1 3.823,2.854 4.313,3.115 0.49,0.26 10 false 2 3.802,2.063 4.292,2.323 0.49,0.26 10 false 1 3.719,3.052 4.208,3.313 0.49,0.26 10 false GV1 4.99,3.052 5.479,3.313 0.49,0.26 10 false G19

CAUTION / NOTICE / HINT

HINT:
·

Perform the simulation method by selecting the "Check Mode" (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting the "Check Mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).



PROCEDURE

1.CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)
a.

Turn the ignition switch off.

C364210E02
4.417,0.583 4.833,0.833 0.417,0.25 1.021,1.635 1.021,1.052 false 5.813,0.74 5.948,0.74 false 5.583,1.177 5.969,1.177 false 4.396,2.448 4.563,2.083 true 4.771,2.458 4.656,2.24 true 5.49,0.563 6.01,0.281 true 5.406,0.573 4.844,0.313 true 0.646,1.656 1.688,2.094 1.042,0.438 10 false Front Passenger Side Squib 1.104,0.708 1.302,0.938 0.198,0.229 10 false F 1.281,0.708 1.479,0.938 0.198,0.229 10 false E 1.573,0.698 1.771,0.927 0.198,0.229 10 false D 1.698,0.698 1.896,0.927 0.198,0.229 10 false C 1.979,1.667 3.083,2.094 1.104,0.427 10 false Center Airbag Sensor 5.094,0.083 6.406,0.354 1.313,0.271 10 false Connector E 4.531,0.615 4.833,0.854 0.302,0.24 10 false V1 5.99,0.667 6.365,0.917 0.375,0.25 10 false SST 6.021,1.094 6.948,1.323 0.927,0.229 10 false Color: Orange 4.406,1.708 4.979,1.938 0.573,0.229 10 false DLC3 5.927,1.688 6.688,1.938 0.76,0.25 10 false DTC 52 4.281,2.469 4.615,2.688 0.333,0.219 10 false CG 4.729,2.479 5.104,2.677 0.375,0.198 10 false TC 4.625,0.229 5,0.479 0.375,0.25 10 false P+ 6.073,0.208 6.448,0.458 0.375,0.25 10 false P-


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the front passenger airbag.


d.

Connect SST (resistance 2.1 Ω) to connector E.


CAUTION:

Never connect a tester to the front passenger airbag (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting them.

·

Insert straight SST into the terminals of the connector.



SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch on (IG), and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


j.

Check the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1805, B1806, B1807, B1808 or 52 is not output.


HINT:

DTCs other than DTC B1805, B1806, B1807, B1808 or 52 may be output at this time, but they are not related to this check.




NG

2.CHECK CONNECTOR

OK

REPLACE FRONT PASSENGER AIRBAG ASSEMBLY

2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from the instrument panel wire.


d.

Check that the instrument panel wire connectors (on the front passenger side airbag) are not damaged.

OK:

Lock button is not disengaged, and claw of lock is not deformed or damaged.




OK

3.CHECK INSTRUMENT PANEL WIRE

NG

4.CHECK INSTRUMENT PANEL WIRE ASSEMBLY
3.CHECK INSTRUMENT PANEL WIRE
a.
C368101E01
0.406,0.656 0.406,0.094 0.406,0.094 0.521,0.094 false 0.875,2.177 1.146,2.042 true 1.583,2.219 1.271,2.042 true 1.427,2.677 1.729,2.677 false 0.563,0.031 2.656,0.271 2.094,0.24 10 false Front Passenger Side Squib 0.542,0.865 0.813,1.104 0.271,0.24 10 false F 0.76,0.865 1.031,1.104 0.271,0.24 10 false E 1.125,0.865 1.396,1.104 0.271,0.24 10 false D 1.26,0.865 1.531,1.104 0.271,0.24 10 false C 1.615,0.875 1.885,1.115 0.271,0.24 10 false B 1.865,0.865 2.135,1.104 0.271,0.24 10 false A 0.667,2.156 0.938,2.396 0.271,0.24 10 false P+ 1.125,1.396 1.792,1.615 0.667,0.219 10 false V1 2.073,0.521 2.938,0.906 0.865,0.385 10 false Center Airbag Sensor 1.771,2.594 2.844,2.844 1.073,0.25 10 false Color: Orange 1.615,2.208 1.885,2.448 0.271,0.24 10 false P-

Disconnect the connector from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch on (IG).


d.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
V1-2 (P+) - Body ground Below 1 V
V1-1 (P-) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
V1-2 (P+) - V1-1 (P-) Below 1 Ω
V1-2 (P+) - Body ground 1 MΩ or higher
V1-1 (P-) - Body ground



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
V1-2 (P+) - V1-1 (P-) 1 MΩ or higher




NG

4.CHECK INSTRUMENT PANEL WIRE ASSEMBLY

OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

4.CHECK INSTRUMENT PANEL WIRE ASSEMBLY
a.
C368097E01
0.365,1.635 0.365,1.188 false 0.917,1.052 0.917,0.917 0.917,0.917 0.083,0.917 false 0.083,0.917 0.083,0.167 0.083,0.167 0.167,0.167 false 1.594,1.052 1.594,0.25 1.594,0.25 1.719,0.25 false 0.76,3.313 1.01,3.208 true 1.396,3.323 1.115,3.198 true 1.969,3.927 2.146,3.594 true 2.458,3.927 2.281,3.594 true 0.229,0.094 1.302,0.531 1.073,0.438 10 false Instrument Panel Wire Assembly 1.76,0.177 3.229,0.469 1.469,0.292 10 false Instrument Panel Wire 2.094,0.906 2.969,1.292 0.875,0.385 10 false Center Airbag Sensor 1.927,1.292 2.229,1.51 0.302,0.219 10 false A 1.677,1.281 1.979,1.5 0.302,0.219 10 false B 1.302,1.281 1.604,1.5 0.302,0.219 10 false C 1.083,1.281 1.385,1.5 0.302,0.219 10 false D 0.708,1.271 1.01,1.49 0.302,0.219 10 false E 0.479,1.271 0.781,1.49 0.302,0.219 10 false F 0.156,1.667 1.677,1.938 1.521,0.271 10 false Front Passenger Squib 0.969,2.49 1.531,2.719 0.563,0.229 10 false V1 2.167,2.719 2.729,2.948 0.563,0.229 10 false GV1 0.542,3.26 1.104,3.49 0.563,0.229 10 false P+ 1.448,3.313 2.01,3.542 0.563,0.229 10 false P- 1.823,3.938 2.385,4.167 0.563,0.229 10 false P+ 2.469,3.948 3.031,4.177 0.563,0.229 10 false P-

Disconnect the instrument panel wire assembly connector from the instrument panel wire.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch on (IG).


d.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
V1-2 (P+) - Body ground Below 1 V
V1-1 (P-) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
V1-1 (P-) - GV1-2 Below 1 Ω
V1-2 (P+) - GV1-1
V1-1 (P-) - V1-2 (P+) 1 MΩ or higher
V1-1 (P-) - Body ground
V1-2 (P+) - Body ground




OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

NG

REPAIR OR REPLACE INSTRUMENT PANEL WIRE ASSEMBLY