Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1815/54  Short in Front Passenger Side Squib 2nd Step Circuit  B1816/54  Open in Front Passenger Side Squib 2nd Step Circuit  B1817/54  Short to GND in Front Passenger Side Squib 2nd Step Circuit  B1818/54  Short to B+ in Front Passenger Side Squib 2nd Step Circuit  


DESCRIPTION

The front passenger side squib 2nd step circuit consists of the center airbag sensor and the front passenger airbag.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the front passenger side squib 2nd step circuit.

DTC No. DTC Detection Condition Trouble Area
B1815/54 Center airbag sensor receives a line short signal 5 times in the front passenger side squib 2nd step circuit during primary check.
·

Instrument panel wire

·

Instrument panel wire assembly

·

Front passenger airbag (Front passenger side squib 2nd step)

·

Center airbag sensor


B1816/54 Center airbag sensor receives an open signal in the front passenger side squib 2nd step circuit for 2 seconds.
·

Instrument panel wire

·

Instrument panel wire assembly

·

Front passenger airbag (Front passenger side squib 2nd step)

·

Center airbag sensor


B1817/54 Center airbag sensor receives a short to ground signal in the front passenger side squib 2nd step circuit for 0.5 seconds.
·

Instrument panel wire

·

Instrument panel wire assembly

·

Front passenger airbag (Front passenger side squib 2nd step)

·

Center airbag sensor


B1818/54 Center airbag sensor receives a short to B+ signal in the front passenger side squib 2nd step circuit for 0.5 seconds.
·

Instrument panel wire

·

Instrument panel wire assembly

·

Front passenger airbag (Front passenger side squib 2nd step)

·

Center airbag sensor



WIRING DIAGRAM

C368093E02
5.188,4.135 6.563,4.406 1.375,0.271 10 false Center Airbag Sensor 0.719,3.573 2.646,3.948 1.927,0.375 10 false Front Passenger Side Squib 2.125,2.156 2.615,2.417 0.49,0.26 10 false P2+ 2.573,2.073 3.063,2.333 0.49,0.26 10 false 2 2.563,2.833 3.052,3.094 0.49,0.26 10 false 1 2.521,2.26 3.01,2.521 0.49,0.26 10 false V2 3.719,2.26 4.208,2.521 0.49,0.26 10 false GV1 4.99,2.25 5.479,2.51 0.49,0.26 10 false G19 5.063,2.052 5.552,2.313 0.49,0.26 10 false 1 5.083,2.854 5.573,3.115 0.49,0.26 10 false 2 2.156,2.958 2.646,3.219 0.49,0.26 10 false P2- 5.375,2.25 5.865,2.51 0.49,0.26 10 false P2+ 5.354,3.052 5.844,3.313 0.49,0.26 10 false P2- 2.531,3.052 3.021,3.313 0.49,0.26 10 false V2 3.823,2.854 4.313,3.115 0.49,0.26 10 false 4 3.802,2.063 4.292,2.323 0.49,0.26 10 false 3 3.719,3.052 4.208,3.313 0.49,0.26 10 false GV1 4.99,3.052 5.479,3.313 0.49,0.26 10 false G19

CAUTION / NOTICE / HINT

HINT:
·

Perform the simulation method by selecting the "Check Mode" (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting the "Check Mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).



PROCEDURE

1.CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB 2ND STEP)
C364211E02
4.333,0.583 4.75,0.833 0.417,0.25 0.813,1.427 0.813,0.958 false 5.625,0.979 5.917,0.979 false 5.417,1.198 5.677,1.438 false 4.188,2.51 4.406,2.135 true 4.635,2.49 4.49,2.313 true 4.75,0.323 5.219,0.563 false 5.875,0.323 5.323,0.573 false 0.885,0.635 1.198,0.833 0.313,0.198 10 false F 1.052,0.635 1.365,0.833 0.313,0.198 10 false E 1.365,0.635 1.677,0.833 0.313,0.198 10 false D 1.479,0.635 1.792,0.833 0.313,0.198 10 false C 0.208,1.448 1.552,1.844 1.344,0.396 10 false Front Passenger Side Squib 2nd Step 1.76,1.583 2.885,1.99 1.125,0.406 10 false Center Airbag Sensor 4.448,0.615 4.76,0.813 0.313,0.198 10 false V2 4.906,0.104 5.896,0.365 0.99,0.26 10 false Connector E 5.958,0.896 6.344,1.115 0.385,0.219 10 false SST 5.76,1.396 6.667,1.625 0.906,0.229 10 false Color: Black 5.74,1.75 6.323,1.979 0.583,0.229 10 false DTC 54 4.271,1.719 4.719,1.927 0.448,0.208 10 false DLC3 4.073,2.521 4.385,2.719 0.313,0.198 10 false CG 4.583,2.521 4.896,2.719 0.313,0.198 10 false TC 4.438,0.229 4.75,0.427 0.313,0.198 10 false P2+ 5.938,0.25 6.25,0.448 0.313,0.198 10 false P2-

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the front passenger airbag.


d.

Connect SST (resistance 2.1 Ω) to the connector E.


CAUTION:

Never connect a tester to the front passenger airbag (front passenger side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting them.

·

Insert straight SST into the terminals of the connector.



SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 60 seconds.


f.

Turn the ignition switch on (IG), and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


j.

Check the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1815, B1816, B1817, B1818 or 54 is not output.


HINT:

DTCs other than DTC B1815, B1816, B1817, B1818 and 54 may be output at this time, but they are not related to this check.




NG

2.CHECK CONNECTOR

OK

REPLACE FRONT PASSENGER AIRBAG ASSEMBLY

2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from the instrument panel wire.


d.

Check that the instrument panel wire connectors (on the front passenger side airbag) are not damaged.

OK:

Lock button is not disengaged, and claw of lock is not deformed or damaged.




OK

3.CHECK INSTRUMENT PANEL WIRE

NG

4.CHECK INSTRUMENT PANEL WIRE ASSEMBLY
3.CHECK INSTRUMENT PANEL WIRE
C368100E01
0.396,0.667 0.396,0.104 0.396,0.104 0.531,0.104 false 0.875,2.219 1.146,2.052 false 1.594,2.271 1.292,2.052 false 0.583,0.031 2.99,0.313 2.406,0.281 10 false Front Passenger Side Squib 2nd Step 0.542,0.865 0.854,1.063 0.313,0.198 10 false F 0.771,0.865 1.083,1.063 0.313,0.198 10 false E 1.135,0.865 1.448,1.063 0.313,0.198 10 false D 1.271,0.865 1.583,1.063 0.313,0.198 10 false C 1.625,0.865 1.938,1.063 0.313,0.198 10 false B 1.865,0.854 2.177,1.052 0.313,0.198 10 false A 2.063,0.479 2.927,0.854 0.865,0.375 10 false Center Airbag Sensor 1.146,1.375 1.458,1.573 0.313,0.198 10 false V2 0.573,2.177 0.885,2.375 0.313,0.198 10 false P2+ 1.604,2.26 1.917,2.458 0.313,0.198 10 false P2-

a.

Disconnect the connector from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch on (IG).


d.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
V2-2 (P2+) - Body ground Below 1 V
V2-1 (P2-) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
V2-2 (P2+) - V2-1 (P2-) Below 1 Ω
V2-2 (P2+) - Body ground 1 MΩ or higher
V2-1 (P2-) - Body ground



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
V2-2 (P2+) - V2-1 (P2-) 1 MΩ or higher




NG

4.CHECK INSTRUMENT PANEL WIRE ASSEMBLY

OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

4.CHECK INSTRUMENT PANEL WIRE ASSEMBLY
a.
C368096E01
1.521,1.063 1.521,0.323 1.521,0.323 1.677,0.323 false 0.917,1.073 0.917,0.917 0.917,0.917 0.083,0.917 false 0.083,0.917 0.083,0.167 0.083,0.167 0.25,0.167 false 0.344,1.625 0.344,1.198 false 0.688,3.24 0.979,3.24 false 2.052,3.927 2.365,3.604 false 2.823,3.875 2.5,3.604 false 1.135,3.24 1.427,3.24 false 0.302,0.073 1.365,0.49 1.063,0.417 10 false Instrument Panel Wire Assembly 0.49,1.292 0.802,1.49 0.313,0.198 10 false F 0.698,1.292 1.01,1.49 0.313,0.198 10 false E 1.083,1.292 1.396,1.49 0.313,0.198 10 false D 1.292,1.292 1.604,1.49 0.313,0.198 10 false C 1.677,1.292 1.99,1.49 0.313,0.198 10 false B 1.927,1.302 2.24,1.5 0.313,0.198 10 false A 2.083,0.906 2.948,1.313 0.865,0.406 10 false Center Airbag Sensor 1.729,0.229 3.177,0.51 1.448,0.281 10 false Instrument Panel Wire 0.125,1.656 1.219,2.083 1.094,0.427 10 false Passenger Squib 2nd Step 0.969,2.594 1.281,2.792 0.313,0.198 10 false V2 2.167,2.792 2.479,2.99 0.313,0.198 10 false GV1 0.365,3.146 0.677,3.344 0.313,0.198 10 false P2+ 1.49,3.156 1.802,3.354 0.313,0.198 10 false P2- 1.885,3.927 2.198,4.125 0.313,0.198 10 false P2+ 2.75,3.896 3.063,4.094 0.313,0.198 10 false P2-

Disconnect the instrument panel wire assembly connector from the instrument panel wire.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch on (IG).


d.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
V2-2 (P2+) - Body ground Below 1 V
V2-1 (P2-) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
V2-2 (P2+) - GV1-3 Below 1 Ω
V2-1 (P2-) - GV1-4
V2-2 (P2+) - V2-1 (P2-)
V2-2 (P2+) - Body ground 1 MΩ or higher
V2-1 (P2-) - Body ground




OK

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

NG

REPAIR OR REPLACE INSTRUMENT PANEL WIRE ASSEMBLY