Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1860/64  Short in Driver Side Knee Airbag Squib Circuit  B1861/64  Open in Driver Side Knee Airbag Squib Circuit  B1862/64  Short to GND in Driver Side Knee Airbag Squib Circuit  B1863/64  Short to B+ in Driver Side Knee Airbag Squib Circuit  


DESCRIPTION

The driver side knee airbag squib circuit consists of the center airbag sensor and the driver side knee airbag.

This circuit signals the SRS to deploy when deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the driver side knee airbag squib circuit.

DTC No. DTC Detection Condition Trouble Area
B1860/64 Center airbag sensor detects line short signal 5 times in driver side knee airbag squib circuit during primary check.
·

Instrument panel wire

·

Driver side knee airbag (Driver side knee airbag squib)

·

Center airbag sensor


B1861/64 Center airbag sensor detects open signal in driver side knee airbag squib circuit for 2 seconds.
·

Instrument panel wire

·

Driver side knee airbag (Driver side knee airbag squib)

·

Center airbag sensor


B1862/64 Center airbag sensor detects short to ground signal in driver side knee airbag squib circuit for 0.5 seconds.
·

Instrument panel wire

·

Driver side knee airbag (Driver side knee airbag squib)

·

Center airbag sensor


B1863/64 Center airbag sensor detects short to B+ signal in driver side knee airbag squib circuit for 0.5 seconds.
·

Instrument panel wire

·

Driver side knee airbag (Driver side knee airbag squib)

·

Center airbag sensor



WIRING DIAGRAM

H101119E56
5.208,4.052 6.583,4.406 1.375,0.354 10 false G19 5.396,2.219 5.802,2.427 0.406,0.208 10 false DK+ 5.198,2.156 5.354,2.365 0.156,0.208 10 false 9 5.135,2.948 5.323,3.156 0.188,0.208 10 false 10 2.49,2.156 2.646,2.365 0.156,0.208 10 false 1 2.49,2.948 2.677,3.156 0.188,0.208 10 false 2 5.396,3.021 5.771,3.229 0.375,0.208 10 false DK- 2.115,2.125 2.573,2.333 0.458,0.208 10 false DK+ 2.125,2.927 2.5,3.135 0.375,0.208 10 false DK- 0.615,3.521 2.531,3.917 1.917,0.396 10 false G14 0.625,3.677 2.542,4.073 1.917,0.396 10 false Driver Side Knee Airbag Squib 5.208,4.219 6.583,4.573 1.375,0.354 10 false Center Airbag Sensor

CAUTION / NOTICE / HINT

HINT:
·

Perform the simulation method by selecting Check Mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting Check Mode (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).



PROCEDURE

1.CHECK DRIVER SIDE KNEE AIRBAG ASSEMBLY (DRIVER SIDE KNEE AIRBAG SQUIB)
a.

Turn the ignition switch off.

C364212E02
4.333,0.417 4.75,0.667 0.417,0.25 0.865,1.219 0.865,0.719 false 4.292,2.51 4.448,2.177 true 4.635,2.521 4.542,2.344 true 0.927,0.365 1.24,0.563 0.313,0.198 10 false D 1.115,0.365 1.427,0.563 0.313,0.198 10 false C 0.24,1.24 1.281,1.635 1.042,0.396 10 false Driver Side Knee Airbag Squib 1.458,1.344 2.333,1.813 0.875,0.469 10 false Center Airbag Sensor 5.01,0.104 6.01,0.333 1,0.229 10 false Connector C 4.406,0.448 4.719,0.646 0.313,0.198 10 false G14 4.292,1.823 4.792,2.031 0.5,0.208 10 false DLC3 4.125,2.531 4.438,2.729 0.313,0.198 10 false CG 4.583,2.542 4.896,2.74 0.313,0.198 10 false TC 5.708,1.781 6.313,2.01 0.604,0.229 10 false DTC 64


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the driver side knee airbag.


d.

Connect SST (resistance 2.1 Ω) to connector C.


CAUTION:

Never connect a tester to the driver side knee airbag (driver side knee airbag squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting them.

·

Insert SST straight into the terminals of the connector.



SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch on (IG), and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


j.

Check the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1860, B1861, B1862, B1863 and 64 are not output.


HINT:

DTCs other than DTC B1860, B1861, B1862, B1863 and 64 may be output at this time, but they are not related to this check.




NG

2.CHECK CONNECTOR

OK

REPLACE DRIVER SIDE KNEE AIRBAG ASSEMBLY

2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the instrument panel wire connector (on the driver side knee airbag side) is not damaged.

OK:

Lock button is not disengaged, and claw of lock is not deformed or damaged.




OK

3.CHECK INSTRUMENT PANEL WIRE (DRIVER SIDE KNEE AIRBAG SQUIB CIRCUIT)

NG

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

3.CHECK INSTRUMENT PANEL WIRE (DRIVER SIDE KNEE AIRBAG SQUIB CIRCUIT)
U189119E02
1.323,0.677 1.323,0.156 1.323,0.156 1.417,0.156 false 0.75,0.813 0.75,1.542 false 1,3.448 1.615,3.229 true 2.385,3.469 1.76,3.219 true 1.698,1.552 2.594,1.885 0.896,0.333 10 false Center Airbag Sensor 1.438,0.063 2.865,0.229 1.427,0.167 10 false Instrument Panel Wire 1.844,0.667 1.969,0.833 0.125,0.167 10 false A 1.479,0.406 1.604,0.573 0.125,0.167 10 false B 1.083,0.406 1.208,0.573 0.125,0.167 10 false C 0.865,0.406 0.99,0.573 0.125,0.167 10 false D 0.219,1.563 1.313,1.906 1.094,0.344 10 false Driver Side Knee Airbag Squib 1.219,2.656 2.042,2.823 0.823,0.167 10 false Connector C 0.823,3.052 1.135,3.219 0.313,0.167 10 false G14 0.823,3.469 1.177,3.635 0.354,0.167 10 false DK+ 2.271,3.5 2.625,3.667 0.354,0.167 10 false DK-

a.

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch on (IG).


d.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
G14-1 (DK+) - Body ground Below 1 V
G14-2 (DK-) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
G14-1 (DK+) - G14-2 (DK-) Below 1 Ω
G14-1 (DK+) - Body ground 1 MΩ or higher
G14-2 (DK-) - Body ground



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
G14-1 (DK+) - G14-2 (DK-) 1 MΩ or higher




OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

NG

REPAIR OR REPLACE INSTRUMENT PANEL WIRE